Selective Call Intercom SYSTEM USER’S GUIDE 1308001 REV. C 301 Fulling Mill Road, Suite G ©Copyright 2008 by On-Q/Legrand, Middletown, PA 17057 Inc All Rights Reserved. (800)-321-2343 www.onqlegrand.
TABLE OF CONTENTS A. Introduction 1 B. System Components Overview 2 C. User Interface Overview 3 1. How to Navigate the User Interface 4 2. Pop-up Style Message Screens 5 D. System Operation 6 1. How to Page or “ALL” Call 6 2. How to Reply to a Page 6 3. How to Selectively Call a Location 7 4. How to Reply to a Selective Call 8 5. How to Mute a Unit 8 6. How to Place a Unit in Monitor Mode 9 7. How to Temporarily Disable a Patio Unit 10 8. How to Initiate a Door Call 12 9.
A. Introduction The On-Q/Legrand Selective Call Intercom System (see Figure 1).is an advanced Cat 5 based intercom system consisting of 2-gang Room Units, Patio Units and Door Units connected with a single Cat 5 cable each to an Intercom Module in the enclosure. The Room Units contain an intuitive graphical user interface in the form of a liquid crystal display, similar to today’s cell phones. Communication may occur in a broadcast fashion if desired, or to specific units as selected on the LCD.
B. System Components Overview System Components The following components (in addition to a suitable power supply) are typically utilized to make up the Selective Call Intercom System (see Figure 2). Figure 2 SCI Module Room Unit Patio Unit • • • • Door Unit Video Door Unit Selective Call Intercom Module: This module is typically installed in the On-Q enclosure and is considered the System Command, Communication and Power Router of the system.
C.
1. How to Navigate the User Interface: ROOM1 ALL Press Arrow Buttons to move highlight to selection: ROOM2 PATIO1 DOOR1 SETTINGS Press TALK/SELECT Button to see selection sub-menu: SETTINGS Unit Names Reply Options A down-arrow in the lower-left corner means there are more sub-menu items. Room Options Door Options Patio Options Press down-arrow to see all items: At the end of the sub-menu items, you will see BACK at the bottom of the screen.
2. Pop-up Style Message Screens: ROOM1 ALL Press either Volume Control Button to see bar-graph style screen: ROOM2 Volume Volume PATIO1 DOOR1 SETTINGS Use buttons to control volume: Display changes back to normal after 2 seconds of inactivity. Press MUTE Button to place Unit in MUTE Mode: ROOM1 ALL Mute Mute is is ON. ON. ROOM2 PATIO1 No No other other units units DOOR1 can contact can contact SETTINGS you! you! MUTE button is backlit red While Unit is in MUTE Mode.
D. System Operation 1. How to Page or “ALL” Call ROOM1 ALL Press arrow buttons to highlight “ALL”. ROOM2 PATIO1 DOOR1 SETTINGS Press and Hold TALK/SELECT button and speak: All Units not in MUTE or MONITOR mode, or on a selective call with someone else will hear a tone when TALK/SELECT button is pressed and then hear you speak: (DOOR Units do not receive Pages).
3. How to Selectively Call a Location Press the arrow buttons to highlight the location you want to call. ROOM1 ALL Press and hold the TALK/SELECT button and speak. When you press the button, a tone will be heard at the receiving unit to tell them you are beginning to talk. ROOM2 PATIO1 DOOR1 SETTINGS When you release the button, a second tone is heard at the receiving unit to let them know you have finished speaking and their 10 seconds (default) hands-free reply time has started.
4. How to Reply to a Selective Call The receiver of a Selective Call will hear a tone when the sender presses TALK/SELECT and then the sender talking to them. The receiver of the Selective Call will see their display highlight the location of the sender. When the sender releases the TALK/SELECT Button, a second tone is heard. Receiver now has 10 seconds (default) of hands-free reply time.
6. How to place a Unit in Monitor Mode Press the MONITOR button: The MONITOR button backlight changes from white to red. The display changes for 2 seconds to show that Monitor is ON. This means the microphone in the Unit is turned on and all other non-muted and non-monitored Units will hear an sounds occurring in the monitored room. The display changes back to normal after 2 seconds. The Monitored Unit will not receive Pages or hear Door Unit door tones, but can receive Selective Calls.
7. How to Temporarily Disable a Patio Unit From any Room Unit, press the arrow buttons to highlight the SETTINGS selection. ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS Press the TALK/SELECT button. Press the arrow buttons to highlight Patio Options. SETTINGS Unit Names Reply Options Press the TALK/SELECT button. Room Options Door Options Patio Options Press the arrow buttons to highlight the Patio Unit that you wish to disable. PATIO OPTIONS Select Unit: PATIO1 Press the TALK/SELECT button.
This screen can also be used to control the default volume, chime volume, whether it can be reached by an All Call (Page), whether it can be placed in Monitor Mode and its default timeout before going into Sleep Mode. NOTE: You will need to turn this Patio Unit back ON (following the same steps) before you can utilize it at a later time. 301 Fulling Mill Road, Suite G ©Copyright 2008 by On-Q/Legrand, Middletown, PA 17057 Inc All Rights Reserved. (800)-321-2343 www.onqlegrand.
8. How to initiate a Door Call OFFICE ALL When a guest presses the Door Chime button on a Door Unit, all non-Muted non-Monitored Room Units that are not involved in another conversation will hear a door tone at their unit, and their unit will wake up if asleep and display a pop-up screen for 2 seconds to tell you that the Door Bell is ringing. Front Front Door Door ROOM2 PATIO1 Is Is Ringing. Ringing. DOOR1 SETTINGS The display then goes back to normal with the Door Unit highlighted.
9. How to initiate a Door Release If an electronic door release has been installed and enabled (see P/N 1308003 Installer Manual for more information), the label “Release” appears below the Door label. To initiate a door release, use the Arrow buttons to highlight “Release” Office ALL Family Room Kids Room Front Door Release and press the TALK/SELECT button. All other Room Units will display a message that the Door is being Released OFFICE ALL Front Front Door Door ROOM2 PATIO1 Release Release Activated.
10. How to select a Door Chime Tone One of 20 different Door Tones may be associated with any Door Unit’s Door Chime button. ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS From any Room Unit, use the arrow buttons to highlight the Settings function and then press the TALK/SELECT button. From the Settings screen, use the arrow buttons to highlight Door Options and the press the TALK/SELECT button.
Door Tone Chime List # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Door Tone Name On-Q Sound On-Q Sound Alternate Westminster Long Westminster Short Two Note (Ding Dong) Two Note (Dong Ding) Jetson’s Doorbell Eastern Strings Calypso Party Für Elise Beethoven’s 5th Happy Birthday Pomp & Circumstance Wolf Howl Jingle Bells We Wish You a Merry Christmas Auld Lang Syne Oh Canada America the Beautiful On-Q Sound + Dog Table 1 301 Fulling Mill Road, Suite G ©Copyright 2008 by On-Q/Legrand, Middletown,
E. System Personalization The following section explains how to use any Selective Call Room Unit to personalize both global options and local settings of the Selective Call System using the Settings selection from the Room Unit Main Menu. 1. Choosing Unit Names ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS From any Room Unit in the house,. use the arrow buttons to highlight SETTINGS and press TALK/SELECT. From the SETTINGS screen, use the arrow buttons to highlight Unit Names and press TALK/SELECT.
When you have decided on a New Unit Name, press TALK/SELECT to lock in that Name. The New Unit Name shown now becomes that Unit’s name and all other Room Units interfaces are populated with the Unit’s New Name. Attic Baby’s Room Balcony Bar Basement Bath 1 Bath 2 Bath 3 Bedroom 1 Bedroom 2 Bedroom 3 Bedroom 4 Bonus Room Break Room Breakfast Rm Casita Closet Computer Rm Dad’s Room Deck Den Dining Room Dock Entertain.
2. Modifying Hands-Free Reply Time This is a global option which affects all Room and Patio Units. It determines the amount of time a receiving unit remains in hands free reply mode. From any Room Unit in the home, Use the arrow buttons to highlight SETTINGS and press the TALK/ SELECT button. ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS Use the arrow buttons to highlight Reply Options and press the TALK/SELECT button.
3. Room Options (Local Settings) These options must be configured from the Room Unit in which the option is to be applied. Use the arrow buttons to highlight SETTINGS and press the TALK/SELECT button. ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS Use the arrow buttons to highlight Room Options and press the TALK/SELECT button. SETTINGS Unit Names Reply Options Room Options Door Options Patio Options Use the arrow buttons to highlight a selection and press the TALK/SELECT button.
The Theme option allows you to select one of four different color pallets for that particular Room Unit’s display. ROOM1 ALL ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS ROOM2 PATIO1 DOOR1 SETTINGS Theme 1 Theme 2 301 Fulling Mill Road, Suite G ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS ROOM2 PATIO1 DOOR1 SETTINGS Theme 3 Theme 4 ©Copyright 2008 by On-Q/Legrand, Middletown, PA 17057 Inc All Rights Reserved. (800)-321-2343 www.onqlegrand.
4. Door Options (Local Settings) The Door Options are specific only to the selected Door Unit. Use the arrow buttons to highlight SETTINGS and press the TALK/SELECT button. ROOM1 ALL Use the arrow buttons to highlight Door Options and press the TALK/SELECT button. SETTINGS ROOM2 PATIO1 DOOR1 SETTINGS Unit Names Reply Options Room Options Door Options Patio Options Use the arrow buttons to highlight the Door Unit selection and press the TALK/SELECT button. The selection flashes.
The first setting “Chime:” determines which of the 20 optional door tones will be associated with the door button on that particular Door Unit (see Table 1 for a complete Door Chime Tone list). The Volume and Chime Volume options allow you to set the default volume levels for that particular Door Unit. 301 Fulling Mill Road, Suite G ©Copyright 2008 by On-Q/Legrand, Middletown, PA 17057 Inc All Rights Reserved. (800)-321-2343 www.onqlegrand.
5. Patio Options (Local Settings) The Patio Options are specific only to the selected Patio Unit. Use the arrow buttons to highlight SETTINGS and press the TALK/SELECT button. ROOM1 ALL ROOM2 PATIO1 DOOR1 SETTINGS Use the arrow buttons to highlight Patio Options and press the TALK/SELECT button. SETTINGS Unit Names Reply Options Room Options Door Options Patio Options Use the arrow buttons to highlight the Patio Unit selection and press the TALK/SELECT button. The selection flashes.
The “Volume:” option determines the default volume level at that particular Patio Unit. The “Chime Volume:” option determines the default volume level of Door Chimes played at that particular Patio Unit when someone pushes the doorbell button on a Door Unit. The “All Call:” option enables (YES) or disables (NO) the broadcast Page ability from that Patio Unit. The “Monitor:” option enables (YES) or disables (NO) the Monitor button on that particular Patio Unit.