Use and Care Guide

THANK YOU
Round LED High Bay
to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Commercial Electric!
USE AND CARE GUIDE
ROUND LED HIGH BAY FIXTURE
Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday
SKU# 1000 000 000
Model# HLNHB270-NP09BM
2
Table of Contents
Safety Information
For your safety, always remember to:
□ Turn off the power supply at the fuse or circuit breaker box
before you install the xture.
□ Ground the xture to avoid potential electric shocks and to
ensure reliable starting.
□ Double-check all connections to be sure they are tight
and correct.
□ Wear rubber soled shoes and work on a sturdy wooden
ladder.
□ Account for small parts and destroy packing material,
as these may be hazardous to children.
This xture is designed for use in a circuit protected by a
fuse or circuit breaker. It is also designed to be installed
in accordance with local electrical codes. If you are unsure
about your wiring, consult a qualied electrician or local
electrical inspector, and check your local electrical code.
WARNING: RISK OF SHOCK. House electric
current can cause painful shock or serious
injury unless handled properly.
WARNING: THIS PRODUCT MUST BE
INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
WARNING: MIN 75°C SUPPLY CONDUCTORS.
CAUTION: Turn off the main power at the
circuit breaker before installing the xture, in
order to prevent possible shock.
NOTICE: All electrical connections must be in
accordance with local and National Electrical Code
(N.E.C.) standards. If you are unfamiliar with proper
electrical wiring connections obtain the services of a
qualied electrician.
Remove the xture and the mounting package from
the box and make sure that no parts are missing by
referencing the illustrations on the installation
instructions.
3
Pre-Installation
TOOLS REQUIRED
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Phillips
screwdriver
A
Electrical Ratings
Volts (V) Frequency (HZ) Watts (W) Current (mA) Color Temperature (K) Lumen (lm) Life (Hrs)
120-277 60 270 2300 5000 30000 60000
5
Installation (continued)
□ Install the hook(F)/boom adapter(E) with washer
and screw nut.
Need to use wrench to lock tight of screw nut.
6
□ Lock with screws. □
7
□ Hook: After hook in the ceiling, please lock
the hook with screw.
Boom adapter: Lock the boom with screw (J).
□
ceiling must at least 1.97 in.
5
Attaching the hook/boom adapter
to the Fixture
F+H+J
E+H+J
Figure 7
Hook(F)
Boom(E)
Figure 8
Figure 9
Figure 10
Figure 11
6
6
Purple
Gray
Purple
Gray
Figure 4 Rear cover
Figure 5
Figure 6
Note: The terminal could only accept solid wire or strand
wire with bundle copper end.
N (White)
Screws on terminal
G (Green)
L (Black)
a
knockout.
(Figure 3).
Connect the live, neutral and ground wires through tube
from power supply circuit to the terminal (L-Black,
G-Green, N-White), lock the wires by
screw driver (Figure 5).
(Figure 6).
0-10V dimmer connection: Connect the two 0-10V
dimming wires (Purple+ and gray-) through knockout
washer (C) as picture.
and connect with compatible 0-10V dimmer
See 0-10v dimming schematic on page 6.
Connect the electrical wires from the
power supply to the LED high bay
dimmer.
Figure 1
Bottom View
Figure 3
Figure 2
FCC compliance information is listed as below:
Responsible party: Leedarson America, Inc.
Responsible party address: 300 Technology Court SE Suite 100, Smyrna, GA 30082
Telephone number: [phone]
≥1.97 inch
≥1.97 inch
F+D
Features To Motion Sensor
Control the sensor by the on/off switch. Press the button"-" then the sensor on, press the button"o" then the sensor off.
□
Detection Range
Under the ideal mounting height of 24ft-35ft (suspension mount only), the detects motion up to 39ft.
□
How The Motion sensor Work
The sensor detects the motion by microwave.The xture light up when detects the motion, after the hold time the light off.
□
Hold Time
The time period the light will be ON after the last detection is 15 minites.
Figure 12
Table of Contents ............................. 2
Safety Information ............................ 2
Warranty ....................................
.............................
3
Electrical Ratings 3
Pre-Installation............................... 3
Tools Required.............................. 3
Hardware Included........................... 3
Installation ................................ 4-6
Warranty
LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase.
If it fails to do so, please contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.
FCC STATEMENT
-This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the
receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV
technician for help. Any changes or modications not expressly approved by the manufacture could void the user’s
authority to operate the equipment.
Part Description
cover
screw (M4X16)
Screw (M4X25)
Boom Adapter
Quantity
A 1
B 3
C 3
D 1
E 1
Part Description
Hook
Wave washer
Nut (3/4 "-14)
Screw bolt (M4X6)
Quantity
1
1
1
1
F
H
J
K
B
E
F
K
H
J
C
D
Wrench
1
2
3
4
Sensor Technical Data
5
Motion Sensor On/Off Setting
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1)this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device. Cet appareil est conforme avec Industrie Canada RSS exemptes de licence standard(s).
Son fonctionnement est soumis aux deux conditions suivantes:
(1) cet appareil ne peut pas provoquer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris celles pouvant causer un
mauvais fonctionnement de l'appareil. This Class B digital apparatus complies with Canadian ICES-005 Cet appareil numérique de la classe B
est conforme à la norme NMB-005 du Canada.
ISED STATEMENT
Detection area
120~277 VAC 50/60Hz
Electronic/magnetic ballast,120V, 50/60Hz, 3A;
Electronic/magnetic ballast,277V, 50/60Hz, 2A
<1W
10%/50%/75%/100%
5s/90s/5min/15min
2Lux/10Lux/50Lux/Disable
5.815GHz
<0.3mW
4-pole pluggable clamp te rminal(L,N,N, L’)for 1.5mm²
cable
Max.6m(ceiling mounted),Max.3m(wall mounted)
Max.14mx6m(ceiling mounted),Max.10m(wall mounted)
-20°C~+60°C
IP20
80.2X36.6X23mm
cULus listed,FCC
Operating voltage
Switching capacity
Standby power
Hold-time
Daylight threshold
Microwave frequency
Microwave power
Detection range
Operating termperature
IP rating
Certificate
Interfaces
Mounting height
Size
0-10V Dimming Schematic
WARNING: Refer to Local and National Electrical codes for correctly sizing wire gauge and making the proper electrical connections and
stems. If not
f local codes.
Gray
0-10 Volt Dimmer
(Supplied by others)
Lighting Fixture,
0-10v dimming LED
Driver
Lighting Fixture,
0-10v dimming LED
Driver
Gray
Purple
Purple
Ground-green
Ground-green
Ground-green
Neutral
N
white
Black
Gray
Purple
N
white
Black
Line Black
Red/White
Red
REMARK: Please reference the dimmers manufacturer wiring diagrams for correct wiring of 0-10 Volt Dimmer.
FCC ID:2AB2Q-NHB270NP09M