TableCall Transmitter Operation Manual FCC ID : QBTLTK-1600T TRADE NAME: TABLECALL TRANSMITTER MODEL NO.: LTK-1600T THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. LEE TECHNOLOGY KOREA CO., LTD.
FCC NOTICE WARNING : The antenna must be installed in a manner that ensures a minimum separation distance of 20 centimeters between the antenna and human beings.
TableCall TRANSMITTER 1. RECEIVER (PAGER) 1) SPEC z 7 Segments Display z Rechargeable Battery Included z 1 Button Switch z 5 LEDs z Vibe and LED Flashing Alert z Maximum 10 Table Number Can Be Stored. 2) PAGER SETUP 1. Insert your pager into the slot of its charger base. 2. The red LED on the top lights up and it indicates the pager is charged properly. 3. Whenever you remove a charged pager from its slot, red light will blink with vibration for 10 seconds. 4. “READY” is displayed on LCD.
corresponding waiter pager. (2) After transmitting is finished, green LED is blinking (3) When you press Cancel Button shortly, it transmits cancel data to corresponding waiter pager. 3) TO PAGE MANAGER (1) When you press Manager Button shortly, it transmits cancel table number data to corresponding manager pager. (2) After transmitting is finished, red LED is blinking (3) When you press Cancel Button shortly, it transmits cancel data to corresponding manager pager.
Troubleshooting Transmitter will not display anything a. Make sure there is power to the outlet a. Check all connections. If you try all this and the transmitter still won’t power up your power supply may be bad. If display is still blank, call us Before you call, try some of the following suggestion *Remember that the capability of your system will be affected by: Foil backed wallboard, Metal mesh, wire reinforced glass, metal sheeting, large mirrors, suspended ceilings, lift shafts etc.
● Consult the dealer or an experienced radio/TV technician for help. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device.
WARRANTY LEETEK warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the original date of consumer purchase. This warranty does not include damage to the product resulting from accident, misuse or improper electrical connection. Power supplies are warranted for 60 days. We recommend the use of a surge protector with all equipment.
TableCall Transmitter User Instruction Manual FCC ID : QBTLTK-1600T TRADE NAME: TABLECALL TRANSMITTER MODEL NO.: LTK-1600T THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. LEE TECHNOLOGY KOREA CO., LTD.
TableCall Transmitter 1. Equipment Setup Set up the Tablecall Transmitter on the table in Café, Restaurant and Beer house without any additional setting. 2. System Operation 1) TRANSMITTER (1) SPEC z 3 Buttons z 2 LEDs z Rechargeable (2) TO PAGE WAITER (a) When you press Waiter Button shortly, it transmits table number data to corresponding waiter pager.
Troubleshooting Transmitter will not display anything a. Make sure there is power to the outlet a. Check all connections. If you try all this and the transmitter still won’t power up your power supply may be bad. If display is still blank, call us Before you call, try some of the following suggestion *Remember that the capability of your system will be affected by: Foil backed wallboard, Metal mesh, wire reinforced glass, metal sheeting, large mirrors, suspended ceilings, lift shafts etc.
● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ● Consult the dealer or an experienced radio/TV technician for help. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted.
and licensed persons as defined by the FCC Rules and Regulations. Operation of altered equipment can result in fines, imprisonment, and /or confiscation of such equipment. WARRANTY LEETEK warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the original date of consumer purchase. This warranty does not include damage to the product resulting from accident, misuse or improper electrical connection. Power supplies are warranted for 60 days.