P A G E R T R A N S MI T T E R U S E R I N S T R U C T I O N MA N U A L FCC ID :QBTLTK-1400A Trade Name : PAGER TRANSMITTER Model No. :LTK-1400A THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. L E E T E C H N OL OG IE S K OR E A C O., L T D .
FCC NOTICE WARNING : The antenna must be installed in a manner that ensures a minimum separation distance of 30 centimeters between the antenna and human beings.
T A BL E OF C ONT E NT S Ⅰ. P R E F A C E Ⅱ. T U R N T R A N S MI T T E R O N / O F F Ⅲ. S E N D A P A G E 1 . N U ME R I C ME S S A G E 2 . A L P H A ME S S A G E 3 . P R E - S E T ME S S A G E ( O N ) 4 . A L P H A ME S S A G E ( O N ) 5 . T R A N S MI T I N D I V I D U A L P A G E R N U MB E R 6 . E R R O R MO D E Ⅳ. S E T U P ME N U 1 . ME N U O P T I O N S 1 ) U S E R MO D E 2 ) MA S T E R MO D E 2 .
P A G E R T R A N S MI T T E R Ⅰ. PREFACE Pager transmitter, LTK-1400A is the desktop paging system capable of addressing more than 1000 pagers with Alpha message or Numeric message. It consists of a fully featured encoder with a large 4 line by 64 chara -cter LCD display. Ⅱ.TURNING THE TX ON/OFF * Plug the Pager Transmitter A/C Adaptor into the Pager Transmitter and then into a standard 110 outlet. * And the initial LCD screen is as below. INITIALIZING Reading Setup Alpha Transmitter ROM Ver.: V1.
(3) Input message in ENTER MESSAGE (Maximum available up to 128 characters) and then press ENTER. (4) Transmit message and return to initial screen. (Sending Message Please Wait) ※ To return to an initial screen(1/3) on the process, input CANCEL. 3. PRE-SET MESSAGE(ON) 1) To send the preset default message → Before this process, Make the Pre-Set Msg ON. (1) Input "1" in initial screen and then press ENTER. (2) Go to 1.NUMERIC TYPE using *(←) and #(→) Key and then press ENTER.
1) Set Default Msg:OFF in Menu Options * In initial screen(1/3), input "1" and push SEND then No Message is transmitted. 2) Set Default Msg:ON in Menu Options * In initial screen(1/3), input "1" and push SEND then Message which is set in Set Default Msg is transmitted. 6. ERROR MODE (1) In initial screen, input number which is over 1249 and then press ENTER. (2) "Extension Number Is Invalid" is displayed with transmit nothing and then return to initial screen.(1/3) Ⅳ. SETUP MENU 1.
※ If hour(1-12) or minute(00-59) is set by other number, it moves to default time. 2) SLEEP TIME SETUP (1) Go to 2.Sleep Time Setting using *(←) and #(→) Key and then press ENTER. (2) Select 1.ON or 2.OFF using *(←) and #(→) Key and then press ENTER. (3) Sleep Time is displayed and default Sleep Time is 12:00 AM. (4) Input hour(1-12) and then press ENTER. (5) Input minute(00-59) and then press ENTER. (6) Select AM/PM using *(←) and #(→) Key and then press ENTER. (7) The screen moves to Menu Options screen.
(2) Select one among "Set Pager Alert:" list using *(←) and #(→) Key, and then press ENTER. (3) "Are All Pagers Returned??" is displayed and then press ENTER. (4) "Unplug All Coasters" is displayed and then press ENTER. (5) "Message Sent Plug In Pager" is displayed and transmit message twice and then move to Menu Options. * Pager Alert Message LIST 1.Vibe Only (9292) 2.Vibe & Flash (9696) 4.Flash & Beep (9595) 3.Flash Only (9797) 5.
(1) Go to 8.Set Alpha Msg using *(←) and #(→) Key and then press ENTER. (2) Select 1.Alpha Msg:ON/OFF using *(←) and #(→) Key and then press ENTER. (3) Select 1.ON using *(←) and #(→) Key and then press ENTER. (4) Select 2.Alpha Msg(0-9) using *(←) and #(→) Key and then press ENTER. (5) Input number in Alpha Message(0-9): and then press ENTER. (6) Then input messages (maximum available up to 128 characters) and then press ENTER.
Troubleshooting Transmitter will not display anything a. Make sure there is power to the outlet a. Check all connections. If you try all this and the transmitter still wont power up your power supply may be bad. If display is still blank, call us Before you call, try some of the following suggestion *Remember that the capability of your system will be affected by: Foil backed wallboard, Metal mesh, wire reinforced glass, metal sheeting, large mirrors, suspended ceilings, lift shafts etc.
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. This device complies with Part 15 of the FCC Rules .
WARRANTY LeeTek warrants this product against any defects that are due to faulty material or workmanship for a one-year period after the original date of consumer purchase. This warranty does not include damage to the product resulting from accident, misuse or improper electrical connection. Power supplies are warranted for 60 days. We recommend the use of a surge protector with all equipment.
Hints and Tips Training is the key to success with a paging system. Orientating your entire staff and training your host staff on the use of the paging system is key to the success of the system. As a part of the general host training program, time must be set aside to teach new hires about the use and care of the paging system. Be certain staff members understand the importance of asking for the transmitter back after work.