User's Manual

ManualsBrandsLee Technology Korea ManualsElectronicsPAGING TRANSMITTER

LTK-1100H

PAGER TRANSMITTER

(LT K-1100H)

User Manua l

w w w.lee tek.org

leet ek 20 01 @yahoo.co.kr

Lee Te chnology Kore a.Co.,Lt d(LEET EK)

#4 99-2 Sa ng3dong, Wonm i-gu,

Puchon-cit y, k yunggi-do, Korea

T:82-32-324-98 38 /9

F:82-32-324-9840

FCC ID :QBTLTK-1100H

Trade Name :PAGER TRANSMITTER

Model No. :LTK-1100H

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS :

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED

OPERATION.

Summary of content (9 pages)

PAGE 1
LT K -1 1 0 0 H PAGER T RAN SM I T T ER (LT K -1 1 0 0 H ) U se r M a nua l FCC ID :QBTLTK-1100H Trade Name :PAGER TRANSMITTER Model No. :LTK-1100H THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. w w w.le e t e k .org le e t e k 2 0 0 1 @ya hoo.c o.k r Le e Te chnology Kore a .Co.
PAGE 2
IMPORTANT SAFETY INFORMATION RF E X POSURE ST A T E ME NT Y our Pager T ransmitter contains a radio frequency transmitter. When the button is pushed the transmitter sends our RF signals. CA UT ION: T o comply with F CC RF exposure compliance requirements, a separation distance of at least 8 inches (20 cm) must be maintained between the antenna of this trasmitter and all persons, during normal operation.
PAGE 3
User manual SPECIFICATION z z z z z z z z z z z Pocsag Code Carrier frequency : 457.5750MHz +/- 200Hz Frequency Range: 450.0000 ~ 467.8750MHz FM modulation & FSK (frequency shift keying) Deviation: 4.5KHz FM Accuracy : +/-5% 4.275< 4.5 < 4.725 Date Rate: 1200BPS, 600Hz +/-5Hz Output power : 2W Message: Numeric: Max. 12 digits Address Range: 0001 to 1249 Dimension : W(185) X D(190) X H(51.5) Thank you for purchasing Our Products.
PAGE 4
You can use your transmitter with the 20 degree wedge attached or remove the wedge and lay the Transmitter flat. 2) WALL MOUNT To mount your Transmitter on a wall z Remove the plastic bracket (included) under the Transmitter unit by unlocking the 2 latches. z Place the plastic bracket against the wall and with the aid of a pencil, mark the position of the mounting holes. (Refer to figure below). Mount the Transmitter in a convenient location where a power outlet is available.
PAGE 5
To enter programming mode, press the “SETUP” button and enter the password “1379” followed by “ENTER”. If the password is accepted, the display will show “use * to scroll to menu options”. (Use the “∗ / Menu” key to scroll through the different menu options or press “CANCEL” to exit the system programming menu.) 1) Set the Current Time z z z z At the “Set Current Time” menu, set the hour then press “ENTER” key. Set the minutes and press “ENTER” key. Use the “# /Select” key to select AM or PM.
PAGE 6
the charger bases. z At the “Set Pager Alert” menu, press the “#/Select” key to scroll through the different alert options. z After making a selection, press the “ENTER” key 3 times. After sending the code, the coasters will now respond with your new selection. z Press “CANCEL” key to exit the system programming menu z Return all the coasters to the charger base or plug the power supply. The coasters are ready to receive the page with the new alert.
PAGE 7
• • Press “ENTER” key 3 times. After sending the signal, all the coasters will light up once to tell you that they received the new code. Press “CANCEL” key to exit the system programming menu. To test the coasters with Out of Range off, unplug the power supply that is connected to the transmitter. After 30 - 45 seconds, all the coasters should not play the melody since the Out of Range was turned off. If all or some of the coasters are playing the melody, repeat the procedure above.
PAGE 8
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ● Reorient or relocate the receiving antenna. ● Increase the separation between the equipment and receiver. ● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
PAGE 9
I need to send some transmitter in for repair - What do I do? Within warranty period / Covered by our Product-Care Program: Ship malfunctioning components to the following address: 3rd FL, #499-2 Sang 3-dong, Wonmi-gu, Puchon-city, Kyunggi-do, Korea Tel: 82-32-678-8605 Fax: 82-32-324-9840 1. Pack the components securely 2. Enclose a note with a brief description of the problem 3. Include a business card 4. Ship the equipment in a traceable manner for your protection. (ie UPS ). 5.