Troubleshooting Guide

Note: To add each additional 52 function LED/RGB light set (up
to 8 total sets end-to-end) follow the above procedure.
PLEASE NOTE: Upon the completion of the end-to-end
connection of each additional 52 function LED/RGB light set; if
synchronization of the combined sets does not occur; simply
unplug the initial light set from the 120V power source (outlet),
and then re-plug back-in to the 120V power source (outlet) to
ensure that all sets connected (up to 8 sets) are matching in
color and are in timed function synchronization.
LED19
Fig 1
REMOTE CONTROL OPERATION
Included is the remote control that operates the color and
function of your LED/RGB light set (Fig 2).
A CR2025 Battery is included within the remote control. Before
operating the remote; remove the thin plastic film that has been
inserted - by slightly pulling downward away from the lower
portion of the remote control.
Fig 3
END-TO-END CONNECTION AND
SYNCHRONIZATION PROCEDURE
1. To add a 2nd 52 function LED/RGB light set to the initially
(plugged-in) 52 function LED/RGB light set by making the
“traditional” end-to-end plug connection – standard female
end from the initial (plugged-in) light set to that of the
standard male plug end from the second set (Fig 1).
The end-to-end connection and synchronization procedure is
now complete!
RGB LIGHTING TECHNOLOGY
This advanced LED/RGB technology allows for the user to
select their favorite color and function of lighting with a simply
push of a button!
There are 52 LED/RGB color & function lighting combinations
available. Please note; due to this LED/RGB technology there
are limitations to each color having an equal acquisition to all
listed functions on the remote control. (See chart below).
Each individual light set can operate separately by the use of
the remote control provided; with also having the capability of
allowing for the synchronization and end-to-end connection
of up to 8 sets.
Note; although each individual LED/RGB light set is provided
with a remote control; only 1 remote control will be required to
operate up to 8 connected light sets.
Select
Favorite
SELECT A FAVORITE:
• Press the “Select Favorite” button if you wish to store a favorite
color or function combination.
• You are able to record & store up to 5 of your “Favorites” – For
future viewing – by pressing the “Play Favorite” & “Cycle
Favorite” buttons located on your remote control.
• Note: The lights will flash BLUE 3 times – indicating a successful
recording of a “Favorite”.
Play
Favorite
PLAY YOUR FAVORITES:
• Press the “Play Favorite” button to view each of your selected
favorites.
• With every push of this button; you can view each previously
recorded “ Select Favorite” individually.
• Note: When pressing the button for the 6th time – Your 1st
recorded selection will be on display.
• Note: If no “Favorites” have yet been selected/recorded – by the
use of the “Select Favorite” button – The lights will flash PURPLE 3
times – indicating that no favorites have yet been
selected/recorded.
Cycle
Favorite
CYCLE YOUR FAVORITES:
• Press the “Cycle Favorite” button to have up to 5 of your
selected favorites cycle through a personalized demonstration
of ALL of your favorite color & function combinations!
• Note: If no “Favorites” have yet been selected/recorded – by the
use of the “Select Favorite” button – The lights will flash PURPLE 3
times – indicating that no favorites have yet been
selected/recorded.
SPECIAL FEATURES:
TIMER FEATURE:
• Press the “Timer” button; the lights will flash GREEN 3 times –
Indicating that the 6 hour “On” / 18 hour “Off” timer has now been
activated.
• Note: The lights will automatically resume back to the “On”
position – 24 hours from when it was initially activated.
• Press the “Timer” button again, the lights will flash RED 3
times – Indicating that the timer feature has now been deactivated.
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓ ✓
✓
1. Red
2. Blue
3. Green
4. Purple
5. Yellow
6. White
7. Multi
8. Teal
Total no. of functions
Steady Flash Firefly Fireworks Slow fade 2 Color
Variable
8 Color
Change
8 Color
Jump
8 8 8 8 8 8 1 1 1 1
Demo
✓
Cycle
Favorite
Color / Function
52 LIGHTING COMBINATIONS:
Fig 2
NOTE: Check the light set for any loose, unlit or damaged
bulbs. Although the light set will still operate, the bulbs must
be replaced promptly to ensure the performance and life
expectancy of the item.
NOTE: Replacement bulbs are provided; this is a specialty
LED/RGB bulb. Do not attempt to replace with a standard
LED or incandescent bulb. Should you require additional
bulbs please contact our customer service department at
1-888-831-6656.
NOTE: In order to determine which color replacement bulb
is needed; select “Steady” function and “Multi” (M) color on
your remote control; to determine which color is absent.
1. If the light set does not illuminate. Press the on/off button
on your remote control. If failure to light persists the battery
may need to be replaced. Insert a CR2025 battery; aligning
the appropriate ( +/- ) markings accordingly.
NOTE: By reducing your distance from the light set(s); you
may achieve better remote control reception.
If the light set fails to light due to a damaged or defective
remote control; a new remote control can be provided
through our customer service center.
2. If failure to light persists the fuse may need to be replaced.
This product employs an overload protection fuse. A blown
fuse indicates an overload or short-circuit situation. If the
fuse blows, unplug the product from the outlet. Also unplug
any additional strings that may be attached to the
product. Replace the fuse as per the following instructions
(follow product marking for proper fuse rating). If the
replacement fuse blows, a short-circuit may be present
and the product should be discarded.
(a) Before changing fuses, make sure that the set is
unplugged.
(b) Grasp plug and remove it from the receptacle or other
outlet device. Do not unplug by pulling on the cord.
(c) Slide open the fuse access cover of the plug towards
the blades (Fig 3).
(d) Remove fuses carefully.
(e) Risk of fire. Replace fuses only with 3 amp, 125 volt fuses
(provided with product).
(f) Close fuse cover. Make sure door is fully closed and the
fuses are completely covered.
(g) Risk of Fire. Do not replace the attached plug. Plug
contains a safety device (fuse) that should not be
removed.
3. A delayed response while switching between color
selections on the remote control. This is in no way a
malfunction of the light set, but is a normal operating
response due to the complexity of the technology.
All bulbs must independently receive their signal to alter to
the correct color selected. Some bulbs may receive their
signals quicker than others, hence a delayed receiver
response may occur. Again, this is innate of the technology
and a normal response.
TROUBLESHOOTING
15”
11.25”
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off andon, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver. —Connect the
—Consult the dealer or an experienced radio/TV technician for help.
equipment into an outlet on a circuit different from that to which the receiver is
connected.
NOTE 2: Any changes or modifications not expressly approved by the party
responsiblefor compliance could void the user’s authority to operate
the equipment.
FCC/IC Radiation Exposure Statement?This equipment complies
with FCC/IC RSS-102 radiation exposure limits set forth for
an uncontrolled environ-ment.
IC WARNING
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference; and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions
(2) l'utilisateur de l'appareil
radioélectrique subi, même si le
RSS 102 de la FCC/IC
radiations dans un
environnement non controlé.
suivantes: (1) l'appareil ne
doit pas produire de brouillage, et
doit accepter tout brouillage
brouillage est susceptible d'en
Déclaration de la FCC et d’IC sur
Cet appareil est conforme à la norme
relative aux limites d’exposition aux