INSTRUCTION MANUAL DSQD 4 Channel Digital Receiver DSQD, DSQD/AES3 Fill in for your records: Serial Number: Purchase Date: Rio Rancho, NM, USA www.lectrosonics.
DSQD Manual Table of Contents Introduction ............................................................................ 2 General Technical Description ............................................. 2 Encryption............................................................................. 2 Digital Hybrid Wireless® Technology..................................... 3 LCD Screen.......................................................................... 3 Diversity Reception........................................
Digital Receiver Digital Hybrid Wireless® Technology All wireless links suffer from channel noise to some degree, and all wireless microphone systems seek to minimize the impact of that noise on the desired signal. Conventional analog systems use compandors for enhanced dynamic range, at the cost of subtle artifacts (known as “pumping” and “breathing”). Wholly digital systems defeat the noise by sending the audio information in digital form.
DSQD Manual Panels and Features DSQD Front Panel Menu/Select Reset Button Menu navigation buttons Return to previous screen Headphone Volume Adjustment Headphone Jack Channel Selector Buttons USB Port Antenna Bias Power LEDs IR Port Power switch DSQD Rear Panel Dante Ports Or AES3 Outputs on 2 TA3M Jacks (in Place of The 2 Dante Ports Shown) 4 Antenna B Input 50 Ohm BNC Antenna B Loop-thru Output 50 Ohm BNC Antenna A Input 50 Ohm BNC Power Inlet XLR Analog Output Connectors Multi-Frame Com
Digital Receiver IR (infrared) Port Frequency and settings can be transferred to and from the DSQD receiver via this port to an IR enabled transmitter to simplify setup. USB Port For firmware updates and connection to Wireless Designer software. Reset Button For MCU recovery in the event of an interrupted firmware update. Headphone Volume Adjustment Knob adjusts the headphone monitor. Antenna Bias LEDs Illuminated when antenna bias power is turned on.
DSQD Manual LCD Menu Map RF FREQUENCY SEL BACK BACK GROUP TUNE SEL SYNC SETTINGS SEL BACK SEL RF FREQUENCY SEL BACK BACK Press SEL to select desired channel Use arrow keys to select desired compatibility mode Press SEL to select desired channel Use arrow keys to enable or adjust Use arrow keys to highlight desired command BACK Audio Setup 6 GROUP TUNE SEL BACK GROUP TUNE SETUP SEL BACK DIVERSITY SETUP SEL BACK AUDIO LEVEL Press SEL to select desired function Use arrow keys to hig
Digital Receiver SYNC SETTINGS SEL BACK Use arrow keys to highlight desired command Press SEL to select desired function SYNC KEY SEL BACK Use arrow keys to highlight desired command Press SEL to select desired function ENCRYPTION KEY SEL MANAGEMENT BACK Use arrow keys to select encryption key Press SEL to confirm selection IR Sync & Encryption RX ON/OFF SEL BACK Press SEL to select desired channel Use arrow keys to select RX power on/off TX BATTERY TYPE SEL BACK Press SEL to select desir
DSQD Manual Navigating the Menus All Setup Menu items are arranged in a vertical list on the LCD. Press MENU/SEL to enter the menu, then navigate with the UP and DOWN arrows to highlight the desired setup item. NOTE: To guarantee chosen parameters are saved, exit a setup screen BEFORE powering down DSQD. Press MENU/ SEL to enter the menu RF Setup Menu RF Frequency Allows manual selection of the operating frequency for each channel. NOTE: Display varies with compatibility mode selection.
Digital Receiver Group Tune Assign a tuning group to a channel. Group Tune Setup Tuning groups allow the user to set up a list of frequencies, allowing for easy tracking of frequency tuning in the transmitters. Use MENU/SEL to move through the options and UP arrow to make a selection. • Four tuning groups are available, U, V, W, X. • Each group has the option to add or delete a frequency from the list on the right.
DSQD Manual Diversity Setup Diversity is a DSQD feature that safeguards against loss of audio signal caused by RF interference. The DSQD architecture allows three different types of diversity reception. Once chosen, the diversity mode is shown on other screens with a link icon. (Visit the DSQD page on lectrosonics.com for a video with more details on Diversity.
Digital Receiver • Frequency: Again, the receiver channels are paired. In this mode, each channel is set to a different frequency. The DSQD automatically uses whichever receiver’s RF signal quality is better. The use of separate frequencies helps minimize dropouts caused by multi-path phenomenon. This technique uses both switched and ratio diversity for maximum effectiveness. NOTE: To maximize frequency diversity, choose frequencies separated as far apart as possible.
DSQD Manual Audio Setup Menu • JA HYB: Used only for certain digital hybrid transmitters marketed in Japan Audio Level Set audio output level with the level control. The mute button is a toggle used to mute or unmute the audio output. The TONE check box is used to generate a 1 kHz test tone at the audio output. Talkback Setup Audio Polarity Select normal or inverted polarity for each audio channel. Smart Noise Reduction Three levels of noise reduction are available: High, Normal and Off.
Digital Receiver 1. Begin by selecting a key type. Choose Transmitter: Choose one of four Rx channels by using the Channel Selector Buttons, 1, 2, 3 or 4. Hold and press the Channel Selector Button to initiate sync. 2. The DSQD will then display a warning to indicate that there is NO KEY! Select CREATE KEY to generate a new key. NOTE: You must position the transmitter’s IR port directly in front of the DSQD IR port, as closely as possible, to guarantee a successful sync.
DSQD Manual TX Battery Timer Alert Set transmitter battery timer alerts for each channel. Choose to enable/disable alert, set time in hour and minutes and reset timer. Use MENU/SEL to set and move the cursor and the UP and DOWN arrows to change values. Network Settings Allows the user to set network settings when needed. The following controls are available: • DHCP Enable - this is checked if DHCP is used to assign an IP address, Netmask and Default Gateway to the device.
Digital Receiver Restore Defaults Returns all settings to the factory defaults. If YES is chosen, message will appear and DSQD will reboot. Pilot Tone Bypass In Digital Hybrid compatibility mode ONLY, Turn Pilot Tone Bypass on/off. Locale Locale optionally changes the settings on the DSQD based on the region where the receiver is being used.
DSQD Manual Supplied Hardware 21926 Cable USB DCR15/4AU DC power supply 25990 Bracket rear tie 35800 Hex L key wrench 25991 Bracket front tie 28950 Long Cap Screws 27076 Rack flange bracket 27082 Rack handle 28951 Short spacer tubes (4) 28885 SCR10 cap screw 35959 Hole Plug (4) 35664 Rubber foot large (2) A500RA20 Antenna (2) A500RA22 Antenna Unpacking the Unit Compare the packing list enclosed with the DSQD with the original order. Inspect all items for damage.
Digital Receiver Optional Accessories 27080 Dante Port Cover ALP690 Antenna Broad bandwidth for multi-channel systems; directional pattern with 4 dBd RF gain; built-in RF amplifier; versatile mounting options SNA600a Antenna Adjustable elements tune center frequency from 550 to 800 MHz; 3/8” x 16 threaded socket and stud with mounting strap included Coaxial Antenna Cable: ARG 15 A 15 foot antenna cable of standard RG-58 coax cable with BNC connectors at each end.
DSQD Manual Installing two DSQD Receivers into a Single Rack Space The DSQD receiver occupies a half rack space, and comes with hardware to mount two receivers into a single rack space. 4. Insert two (2) cap screws (Part #28885) through the rack handle (Part #27082) holes and install the rack handle onto the flange bracket through the holes in the unit’s front panel. Firmly tighten the cap screws using the hex key (Allen wrench) as shown. 1.
Digital Receiver Rear tie bracket (Part #25990) Tensioning lock nuts on the rear side of the bracket 6. Install one side of the front tie bracket (Part #25991) into the side panel opening in one of the receivers. Insert the screws, but do not tighten them completely at this point. Front tie bracket (Part #25991) Slide the other receiver over the tie bracket and insert the screws, but do not tighten them completely until the rear tie bracket is installed. 7.
DSQD Manual Service and Repair If your system malfunctions, you should attempt to correct or isolate the trouble before concluding that the equipment needs repair. Make sure you have followed the setup procedure and operating instructions. Check the interconnecting cables and then go through the Troubleshooting section in this manual. We strongly recommend that you do not try to repair the equipment yourself and do not have the local repair shop attempt anything other than the simplest repair.
Digital Receiver ISEDC Notices: Per RSS-210 This device operates on a no-protection no-interference basis. Should the user seek to obtain protection from other radio services operating in the same TV bands, a radio licence is required. Please consult Industry Canada’s document CPC-2-1-28, Optional Licensing for Low-Power Radio Apparatus in the TV Bands, for details. Ce dispositif fonctionne selon un régime de non-brouillage et de non-protection.
DSQD Manual 22 LECTROSONICS, INC.
Digital Receiver Rio Rancho, NM 23
LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer. This warranty does not cover equipment which has been abused or damaged by careless handling or shipping. This warranty does not apply to used or demonstrator equipment. Should any defect develop, Lectrosonics, Inc. will, at our option, repair or replace any defective parts without charge for either parts or labor.