Quick Start Guide

Getting to know your device
01
Front BackSide
Charging Base
02
Front
Charging contacts
Call 1 button
SOS button
Voice on/off
button
03
Back
Loudspeaker
Boom
USB cable
Put the SIM card
The SIM card is not included in the package.
A Nano SIM card is available from the user's local operator.
Unscrew the back cover and remove the cover.
Insert the SIM card and make sure it’s activated with
credits.
Put the cover back and tighten the screws.
Before installing the SIM card, check if
the SIM card has a PIN code or not, if
yes, please use a cell-phone to remove
the card's PIN code.
TIP
04
Charging your device
There are two ways to charge your device.
When placing the magnetic USB cable on the
device charging contacts make sure it is posi-
tioned correctly.
The power indicator (red light) should blink when
charging and remain solid when fully charged.
4.1/Charging by magnetic USB cable
01 07
Getting a GPS fix
08 11
Making a Phone Call
10
Fall down alarm
09
Activating an SOS Alarm
When you need help, press the SOS button for 3-4
seconds till you hear a voice prompt of activating an
SOS alarm. This starts the sequence of “help me!”
text message send to your emergency contact num-
bers followed by the outgoing calls.
（Press for 3-4 seconds）
If the device fails to connect to the first number, it will
call the second number after delay of 10 seconds. In
case the second number fails to be connected as
well, the system will connect to the third number etc.
To get an initial fix for the GPS features, use outdoors
or near a window so the device can get a fix on the
satellites. This could take few minutes according to
your environment.
To make a call, press side call button for 3 seconds
and you will hear a beep, and then it will dial the
second number.
Device detects a fall and it will automatically send an
alarm to emergency contacts.
Dimension: 61mm*44mm*16mm
Weight: 40g
Battery: Rechargeable, 3.7V, 800mAh
Charging voltage: 5V DC
Waterproof: IP67
4 locating technologies: GPS, BLE, WIFI, LBS
Due to the daily life activities (like some sports, sit
back on a coach, etc), device may detect a fall incor-
rectly, this situation may cause false alarm. However,
users can manually cancel the fall alert by pressing
SOS button during its beeping.
To end the call, press the SOS button.
Press and hold button 3 seconds, and in the same
time press CALL2 button on charging base, they will
pair to each other via bluetooth.
Between each call, it will have 10 seconds delay,
during this time, user can stop call sequence or prevent
a possible false alarm by pressing the SOS button.
The receiver of the call can also stop call sequence by
pressing 1 on their mobile phone during two way
talking.
Use the side buttons +/- to adjust the sound volume
during a call.
06
What do the lights mean?
Green
Means
Light shows a single flash
rapidly every 3 seconds
Light shows a double flash
rapidly every 3 seconds
The device has a stable
cellular signal
The device is registered to
the cellular network
Blue
Means
Light shows a single flash rapidly every 3 seconds
The device has no latest location fix
Blue
Means
Light shows a double flash
rapidly every 3 seconds
Light Off
The device has latest
location fix
The device is not fixing the
latest location
Red
State
Red ON (solid)
Device has been fully charged
Red shows a double flash
rapidly every 3 seconds
BLE connected
Red
State
Red Blinking Quickly
Red Off or blinking slowly
Battery power is
lower than 20%
The device is charging
Cellular signal indicator--Green
Power indicator--Red
Positioning indicator--Blue
Switching on and off device
05
（All the LEDs will flash rapidly）
To turn on the device: press the SOS button for 1
second, all the LEDs will flash rapidly. The device
can also be turned on automatically by charging via
magnetic USB cable or put it into the docking
station.
1sec.
For the first time use, please fully charge the battery
for around 2~3 hours
TIP
The charging base is equipped with a 2000mAh back
up battery, which can charge the device when the
electricity is off at home or when traveling.
TIP
When the battery level falls below 20% it will send a
low battery warning message to people on the
contact list via text message or APP.
TIP
The charging base light will glow when charging and turn
solid when fully charged.
Place the device on the charging base
Connect the USB cable from charging base to the
AC adaptor.
4.2/ Charging by charging base
Please remember to program emergency
contact numbers. It is not mandatory for
all ten authorized numbers to be set,
however a minimum of one must always
be set.
TIP
Please be patient during the call sequence.
There can be short delays as the alarm
calls phones who maybe out of range or
delivered to people’s voicemail.
TIP
GPS
Lanyard hole
Microphone
SOS button
Cellular signal
indicator- Green
Call button
positioning
indicator- Blue
Silent mode
button
Power indicator-Red
Loudspeaker
Charging contacts
Screw
holes
3sec.
3-4sec.
BEEP!
Very Important: Because it still has few
chances for the non-detected falling
down, we still strongly recommend user to
press SOS button when it has emergency
situation.
TIP
Specification:
Don’t use & store the unit in dusty places.
Don’t put the unit in overheated or over cooled places.
Clean the unit with a piece of dry cloth. Don’t clean
in chemicals, detergent.
Don’t disassemble or refit the unit.
Using other batteries will cause unwanted situation.
Cautions:
Please comply with the instructions to extend the unit life:
3sec.
Quick
Start
Guide
Personal
Mobile
Alarm Device
Ｗ ＩＦＩＧＰＳ ／ＧｌｏｎａｓｓＣｅｌｌｕｌａｒ ＢＬＥ
SOS
2sec.
3sec.
To turn off the device: press and hold the side button
and SOS button together for 3 seconds until the
LEDs turn off.
Warning: Keep the IMEI and SIM in confidential, or
your privacy may expose.
Silent mode button
Hold and press this button for 2 seconds to turn off
voice warnings, press 2 seconds again to turn on voice
warnings.
3sec.
In the same time
FCC Warning:
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generats,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
SAR
Specific Absorption Rate (SAR) information:
This Personal Mobile Alarm System meets the government's requirements for exposure to radio
waves. The guidelines are based on standards that were developed by independent scientific
organizations through periodic and thorough evaluation of scientific studies. The standards
include a substantial safety margin designed to assure the safety of all persons regardless of age
or health. FCC RF Exposure Information and Statement the SAR limit of USA (FCC) is 1.6 W/
kg averaged over one gram of tissue. Device types: Personal Mobile Alarm System (FCC ID:
22AUMJEV-07B-LTE) has also been tested against this SAR limit. This device was tested for
typical body-worn operations with the back of the product kept 0mm from the body. To
maintain compliance with FCC RF exposure requirements, use accessories that maintain a
0mm separation distance between the user's body and the back of the product.
The use of accessories that do not satisfy these requirements may not comply with FCC RF
exposure requirements, and should be avoided.