Instruction Manual

LB55955T
WARNING
STRANGULATION HAZARD － Children have STRANGLED in cords.
Keep this cord out of reach of children (more than 3 feet/1 meter away
from the crib). Never use extension cords with AC adapters. Only use the
AC Adapters provided.
WARNING
Adult assembly required. Keep small parts
away from children when assembling.
Warning Information
＊Keep this instrucon manual for
future reference.
＊For adult use only.
WARNING
·When an AC Adapter is plugged into an electrical outlet, do not the exposed end.
·Test baby monitor before first use, periodically, and when changing locaon of the baby unit(Camera).
·Do not use monitor near water (Such as bathtub, Sink, etc)
·Keep parent unit away from heat sources (Such as stoves, radiators, etc)
·Make sure there is proper venlaon around baby unit and parent unit.
·This product is not a toy. Do not allow children to play with it.
·The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall
remain readily operable.
·The baby monitor should not be considered as a medical device.
While using the baby monitor, it is
strongly recommended to have an adult directly checking on your baby. Premature babies or children
considered at risk must be supervised by your pediatrician or other medical staff.
THIS PRODUCT CANNOT REPLACE
RESPONSIBLE ADULT SUPERVISION
·Use only the original rechargeable baery provided.
·Do not shot-circuit supply terminals.
·Remove baery when product is stored for long periods of me or when ba ery is exhausted.
·Dispose of exhausted baery properly.
·Keep all baeries away from children.
·The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
·Danger of explosion if baery is incorrectly replaced. Replace only with the same or equivalent type.
·Baeries (baery pack or baeries installed) shall not be exposed to excessive heat such as sunshine, fire
or the like.
Baery Warning
Precauons
·Do not overload wall outlets, extension cords, or integral convenience
receptacles as this can result in a risk of fire or electrics shock.
·The baby monitor works beer in temperature ranging between 0℃
and 40℃ (32℉ and 104℉)
·Do not dismantle the appliance. It does not contain any parts that may
be used independently.
·Never Expose the baby monitor for long period to sun’s direct rays and
never place it next to a source of heat, in a damp or very dusty room.
·Never push objects of any kind into this product through openings as
they may touch dangerous
voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind on the
product.
·Do not aempt to service this product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
·The product should be mounted to a wall or ceiling inly as
recommended by the manufacturer.
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following
two condions:
(1) This device may not cause harmful interference, and
(2) This device must accept any
interference received, including interference that may cause undesired operaon.
FCC Cauon
To assure connued compliance, any changes or modificaons not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment. (Example -
use only shielded interface cables when connecng to computer or peripheral devices).
Federal Communicaon Commission Interference
Statement
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rule
s. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communica-
oons. However, there is no guarantee that interference will not
occur in a parcular installaon. If this equipment does cause
harmful interference to radio or television recepon, which can be
determined by turning the equipment off and on, the user is
e
ncouraged to try to correct the interference by one of the
following measures:
. Reorient or relocate the receiving antenna.
. Increase the separaon between the equipment and receiver.
. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
. Consult the dealer or an experienced radio/TV technician for help.
FCC Radiaon Exposure Statement
This equipment complies with FCC RF radiaon exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20
cenmeters between the radiator and your body.
This transmier must not be co-located or operang in conjuncon with any other antenna or
transmier.
The antennas used for this transmier must be installed to provide a separaon distance of at least
20 cm from all persons and must not be co-located or operang in conjuncon with any other
antenna or transmier.
JLB7Tech’s baby monitor warranty policy
JLB7Tech will repair or replace (at our opon) your unit free of charge
for 12 months from the date of purchase if the unit is defecve in
workm
anship or materials. To claim your repair/replacement, the
product must be returned to JLB7Tech together with a copy of the
purchase receipt. In the absence of the purchase receipt, the warranty
will be 12 months from the date of manufacture. This warranty does not
apply to normal wear or damage from misuse, abuse, improper storage
and handling, installaon, accident, unauthorized repair or alteraon.
Please contact our Customer service by Facebook JLB7Tech or via
email for details.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard.
Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitaon est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est suscepble d'en compromere le
fonconnement.
IC Radiaon Exposure Statement:
This equipment complies with IC RSS-102 radiaon exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.
Cet équipement est conforme aux CNR-102 d'Industrie Canada. Cet équipement doit êtreinstallé et ulisé avec une distance minimale de 20 cenmètres entre le radiateur et votrecorps. Cet
émeeur ne doit pas être co-localisées ou opérant en conjonc on avec autreantenn
e ou émeeur. Les antennes ulisées pour cet émeeur doivent être installés eournir une distance de
séparaon d'au moins 20 cenmètre de toute personne et doit pas être co-située ni fonconner en onjoncon avec une autre antenne ou émeeur.
1 meter
Never place the baby unit or the cord
within 1 meter of the crib.
Connect the small plug of the power adapter to the Baby Unit and the other end to a
suitable electrical outlet. Only use the enclosed adapter (5V DC 1000mA).
The baby unit is turned on and the power LED will be green.
Connecng the power supply for the Parent Unit.
Connect the small plug of the power adapter to the parent unit and the other end to
a electrical outlet. Only use the enclosed adapter (5V DC/1000mA).
Recommend charging time of at least 3 hours before first use.
1
3 4
2
Setup and use your digital video baby monitor
B.
C.
When baery is low, the power on off LED (icon) will flash red and on screen
If you use the parent unit for the first time, when you turn on the parent unit, some boot menus
Notice:
will pop-up on the screen, we try to explation status and function on these menus, please
according to the tips to switch to the monitor system interface. When you are fimaliar with
this monitor, you could switch off these on screen tips in menu.
display baery icon will flash red indicang that the baery needs to be
charged.
Precaution: use of battery for Parent Unit
Only charge the battery when the battery life indicator is low. Constant
recharging of your battery before the low battery indicator light comes on will
decrease the life of your batteries.
Installing Baby Unit
A.
Place Baby Unit on a flat surface, such as a desk or shelf or mount the camera on a wall.
Function of keys and LED indicators Start to use monitor
Parent Unit
Status bar
Baby Unit
When camera is powered on, press it the power LED starts to blink, the
camera is in pairing mode, and press it again to exit pairing mode.
Kick Stand
Flip out the kick stand and place the Parent Unit on a
stable, level surface.
Antenna
Microphone
Loudspeaker
USB port
:Camera Antenna
Room Temperature sensor
Pairing button
:Gather room temperature informaon
Battery Door
Open the baery door to change baery.
Antenna
Reset
USB port
Li up antenna to have beer recepon of audio and video
Short press to turn off the parant unit, and need to restart.
Press to switch on/off Power Saving mode (When power saving mode
is enabled, screen will be turned off).
Menu mode (Press to adjust menu sengs)
Press to decrease and increase volume.
Press to open and exit menu opons.
Menu mode (Press to select menu option)
Menu mode (Press to adjust menu sengs)
Press and hold to talk to baby unit.
:Press and hold to switch “On/Off” the unit.
Power
Loudspeaker
Volume down/up
Talk
MENU
Up/Down
Left/Right
Select
Power Saving-on/off
Pairing button
Power on off status LED
Steady Green: Parent Unit is
powered on.
Steady Orange: Charging baery.
Flash Red: Baery Low
Power Saving on off status
Steady Green: Power saving mode is
acvated.
Sound Level indicator
Visual indicator for sound picked up
from baby unit. The louder the
sound is from Baby unit, the more
LEDs are light on.
Power Saving-on/off mode
Screen is switched off to save baery energy. When keep audio on in power saving mode, the screen will
always be off. When keep audio off in power saving mode, when baby cry loud enough, screen is switched
on to display baby’s video. Baby cry level is adjustable from Menu seng (Sensivity Level L, M, H, AUTO).
Microphone
INSTRUCTION MANUAL
PAIR
PAIR
VOL- VOL+
PAIR
SPLIT VIEW
Split Screen View
Press and toggle between single and split screen. Use key
to
move red frame between 2 cameras.
Menu operation
Signal strength reference
Camera number
Baby room temperature
Baery level
Talk funcon is acvated
Zoom in is acvated
Lullaby is acvated
Monitor is muted
Temperature alert is acvated
Scan view is acvated
Adjust Parent Unit LCD
Brightness lighter or darker.
Acvate or deacvate lullaby funcon, 5 lullabies can be chosen. When turn
on lullaby, on Baby Unit side will always hear the ringtone from Parent Unit.
Adjust camera volume : Sound
level from 1 to 5.
ADD: Add addional camera. Two cameras can be added.
: Deacvate lullaby funcon.
Delete: Delete paired camera from the list.
Repeat: Repeat all lullabies.
SCAN: Display paired camera one by one.
View: Select and display the camera.
Split screen view:
Quiet: Baby cry a lile bit to acvate the Parent Unit.
Auto
Acvaon sound level selecon and leave audio off in power saving mode.
: Learning environment sound and acvaon. Recommend for users
having white noise machine, fans and lulllabies near by.
Medium: Baby cry moderate to acvate the Parent Unit.
Loud
Sound Bar
: Baby cry louder to acvate the Parent Unit.
Turn off screen and leave audio on: Keep audio connuously on when
screen is off in power saving mode.
:
This sound bar is disigned for deaf parents to r
eflect sound
level picked up from camera. You can turn visual sound level indicaon
on or off.
High: Beep Alarm is issued when room temperature is higher than
this seng.
Low: Beep Alarm is issued when room temperature is lower than this
seing.
C
: Display temperature in Celsius scale.
F
Temperature calibraon
: Display temperature in Fahrenheit scale.
ON
: Acvate room temperature alarm funcon.
OFF
OFF
: Deacvate room temperature alarm funcon.
: calibrate room temperature display to your
standardized one.
Step 1: Move the parent unit to the same area as the camera. Both parent and baby
unit are switched on.
Step 2: Select ADD in Menu. The next available camera will automacally be
highli
ghted. Press “Select” to begin pairing.
Step 3: Within 10 seconds, press “Pairing buon” of camera.
Step 4: Once successfully paired, the camera light will stop flashing and video will
appear on the monitor screen within 20 seconds.
Baby’s crying sound level
To acvate Parent unit from Power saving mode
Out
In
Zoom
CAM1
2 3 C
Explanaon On/Off : We try to explaon status and funcon on the boot
23 C CAM1
o
23 C
CAM1 CAM2
o
23 C
Use to select audio source between 2 cameras
Monitor only play sound
from the camera which
marked in red frame.
* Use arrow key to move red
frame between 2 cameras.
* Press “
SPLIT VIEW” key to select
and switch to that camera view and
exit split screen view.
menu. You can turn the explanaon on or off based on your usage.
Reset
OK
VOX
OK
VOX
OK
VOX
SPLIT VIEW