OPERATION INSTRUCTION IP Villa Video Intercom System User Manual MC-1053(A-3)
LIMITATION OF LIABILITY ※ The doorbell/camera units should be fitted with an approved weather shield if the chosen position is in direct sunlight, or in contact with rain, snow or irrigation sprinkler systems. ※ This users' manual is supplied 'as is', with no warranties, be it expressed or implied, including, but not limited to, the implied warranties of merchantability, suitability for any exact purpose, or non-infringement of any third party's rights.
Table Tableof ofContents Contents LIMITATION OF LIABILITY..............................................................................1 DISCLAIMER OF WARRANTY.........................................................................1 SAFETY INSTRUCTIONS...............................................................................1 CARING FOR THE ENVIRONMENT BY RECYCLING........................................2 COPYRIGHT STATEMENT..............................................................................
Name 1. Description Of The Indoor Unit Power LED 1 The door 1 LED 1.1 Description On The Indoor Monitoring (Please take actual model as quasi) 2 The door 2 LED 5 13 Speaker LAN 8 Talk 15 DC 12V 4 8 Non-visual Indoor Unit 1 2 3 2 6 Monitoring Observe the image of camera view at entrance in real time with visual indoor unit. For some models, click “Monitoring 1 ” to observe the image of Door 1, and click “Monitoring 2 ” to observe the image of Door 2.
1.2 Specifications of the Indoor Unit Display Resolution Video system 1.3 Fitting for the Indoor Unit A. For the visual indoor unit with 7 inch TFT LCD 7 inch TFT LCD 800(H)X3(RGB)X480(V) PAL/NTSC compatible 1 2 Intercom mode 23mm 220mm Conversation duration Semi- Duplex communication 120 seconds Monitoring 1 Standby status 300mA max. working status 600mA max. Power supply DC 12V Talk Unlock Hang up OPERATION INS 2 IP Villa Video Intercom Sys Quick Guide 160mm Operation temp.
B: For the non-visual indoor unit, users can connect only one outdoor camera to the corresponding interface according to the following wiring diagram. And indoor machine power with a built-in power or an external power optional, please refer to actual control using. B.
* Select the most suitable position where the monitor is located at user's eye level. DC12V AUDIO GND VIDEO DC12V AUDIO GND VIDEO * Switch off power supply before installing. Unshielded wire(≤50m) * Keep more than 30cm away from AC power supply to avoid external interference. DC12V DC12V AUDIO GND VIDEO AUDIO GND VIDEO Shield Shielded wire( 80m) * Keep it away from the water and magnetic field. Shield To install the indoor unit , please follow these steps as below: 2.
◆ MONITORING On Indoor Unit(For the visual indoor machine) 1.7 Operation Introduction On Indoor Unit Please be aware of Connection of 2 outdoor cameras to 1 indoor monitor is required for dual entrance monitoring at least. ◆ VISITOR CALL Standby mode Please be aware of Connection of 2 outdoor cameras is required.
2.2 Soft AP Function 2. System Settings For Indoor Units The indoor unit can be worked in AP mode. If user doesn’t want to connect a wired cable to the indoor device, and user need prepare a wireless router and a smart-phone or a pad with IOS or Android system. The network connection diagram via wireless network please refer to Figure 2 on section 2.1 Device Connect. No menus on the indoor unit can be operated, so users should set up parameters for the indoor unit Web browser. 2.
2.3 Web Browser Operation 2.3.3 Connection Settings 2.3.1 Running Environment Install the software through the Internet browser of OS to conveniently operate the network from a remote location. This device supports C/S, B/S, and access in LAN and WAN. It also supports IP and domain name visiting.
2.4 Quick Setting 1)Through the indoor unit connection to network (or PC), and then to the indoor unit electric start. Note: if the indoor unit and PC connected directly, PC’s IP address to use manual distribution methods, and the IP address of the PC network segment and the indoor unit keep the same network segment. 2)Copy the quick setting guide program “HiCamSearcher_v1.1.exe” from the installation CD to user’s PC, and run it on PC. 2. 2. 3)Press "Next" button, pop-up as below interface.
Click “ ” and download the file “IPDoor.zip” to the PC. Open the zip file to run the file “IPDoor.exe” and it will install indoor unit’s OCX on the PC (according to the method as following figures). 6)Click “OK” to confirm device parameters configuration. 2.5 System Login 1)Open the web browser, and enter IP address “http://XXX.XXX.XXX.XXX”. Note: If the device is connected to the WAN, the IP address should be a public IP address. The system will automatically enter the GUI as follows.
Note: Different router has different settings for port forwarding; please kindly follow your router guide to do the port-forwarding. After the port-forwarding is done, you could view the indoor unit from WAN now. 4)After login, it will enter into “Home” interface of the live view as follows. IPDoor 2014-04-25 11:20:08 2.7 Function Settings 2.6 Port Forwarding If visit indoor unit via Internet Explorer browser from WAN, you must do port forwarding on the router.
Stream: Set up network stream, including main flow and minor flow. Image: Set up the size of view image. Options include Fit size and Src size. image quality is, the bigger the bit rate and the frame rate of the outdoor camera are. Please choose the suitable quality according to your bandwidth. 2.7.2 Media Click “Media” to enter the media parameter setting menu. This interface includes settings for Video and OSD. 2.7.2.1 Media--Video 2.7.2.
2.7.3.2 Network--DDNS 2.7.3.1 Network--Basic Settings Click “Parameters—Network—Basic Settings” to enter the LAN Settings interface. Default IP address of the equipment is 192.168.0.111. The user can set up device network parameters through the operation “Quick Setting Guide”, user can change it according to your network environment. A. LAN Settings [IP Type]: There are two options: “Fixed IP Address” and “dynamic IP Address”.
If not, user must set up parameters about Wifi again. 4. When the equipment connected to the Internet, and also enable the WIFI, when activated, the equipment will be the first to choose Ethernet cable connection mode, if can't connect, then choose WIFI connection. WIFI connection of the ports to use are consistent with cable connection of the ports to use. 2.7.4.1 System-User Click “System—user” to access user setting menu, the default username and password of administrator is “Admin” and “888888”. 2.7.
4) “Sync with NTP” will choose a same time zone with the NTP server automatically. Server name is the NTP server host, and the interval of refresh time includes 1 hour, 2 hours, 12 hours and 24hous. Save all parameters, then it will update as a network clock. 2.7.4.4 System-Device Info Click “System—Device Info” to enter the “Device Information” menu as follows.
According to the above figure for example, click “011->20140414->rec001” to enter into the record list. Click one on the list to playback the record. Click “Parent Folder” to back to the parent directory. 2.7.5 Logout Click “Logout” to log out of the system. 2.7.6 Record(Optional) The models without SD card can't record.
A. Adding by “Scan QR Code” Click “ ” to the next interface, users can scan QR code attached to the machine through the mobile phone or the iPad, and the device UID will be shown. B. Adding by “Manually enter” Click “ ” to the next interface, users can add a new device by UID type or by IP type. a. By UID type After entering the “UID Type” Settings menu, the following fields will need to be completed: Name: Set name for the indoor unit, and saves settings for future usage.
2> After adding the device successfully, the device will appear on the main screen. Click the device, and all the channels of the device will be shown on the screen. Click any channel and it will connect immediately. The background of the channel will be highlighted after connecting successfully(shown as follows). ipdoor 2014-07-29 10:21:30 unit and the mobile phone are both connected to internet.
7> Click “ ”to enter the “System Settings” interface as follows. [Video Views]: Select “1" and only one channel view will be shown on live view. Select “4" and quad channels view will be shown on live view. [Live Preference]: Options include “Real-time” and “Quality”.
4) The functions of the other icons on the live view: Unlock. Name: Set name for the indoor unit, and saves settings for future usage. UID: The device UID (UID is attached to the machine). User: The user name set for entering the indoor unit system. The default is “Admin”. Password: The password set for entering the indoor unit system. The default is “888888". Channel Number: Set the max channels of the device will be connected. Click “ ” to save.
wireless router after starting when hearing a beep again. Note: If users want to connect the device via wireless network, when the device restarts automatically after completing set of the parameters about WIFI, please unplug the Ethernet cable connected to the device, otherwise the device will run via wired network. Appendix 1. Accessing the indoor unit via Mozilla Firefox 1.First, install Firefox on Windows(This document will use Firefox 28.0 as an example). 2.
6. Click the icon “ ” on the right of the address field to display the Chrome web page in an IE-based page, and fill in the IP address of the indoor unit on the IE-based address bar, then click the icon “ ” to access the remote device, fill in the correct user name and password to log in. Default user name and password are “Admin” and “888888".(shown on the red frames as below) 4. During installation, the following figure will appear, click “Add” to confirm to install “IE Tab” add-on.
3) Change the security level for the “Internet” zone from the default “Medium-high” zone to “Medium". Slide the bar up and down between the different security zones. The “Medium” Internet zone will allow a lower security environment for your web browsing. To go even further with enabling the ActiveX controls, click the “Custom Level” button. Under the “Settings” menu, look for the “ActiveX Controls and Plug-ins” options.
FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.