4-wire villa high definition video intercom system
LIMITATION OF LIABILITY ※ The doorbell/camera units should be fitted with an approved weather shield if the chosen position is in direct sunlight, or in contact with rain, snow or irrigation sprinkler systems. ※ This users' manual is supplied 'as is', with no warranties, be it expressed or implied, including, but not limited to, the implied warranties of merchantability, suitability for any exact purpose, or non-infringement of any third party's rights.
Table of Contents Table of Contents LIMITATION OF LIABILITY..............................................................................1 DISCLAIMER OF WARRANTY.........................................................................1 SAFETY INSTRUCTIONS...............................................................................1 CARING FOR THE ENVIRONMENT BY RECYCLING........................................2 COPYRIGHT STATEMENT............................................................................
1.2 Description On LED Indicator 1. Description Of The Indoor Unit In the panel you can find out three LED indicators , with the detailed descriptions, please see the below: 1.1 Description On The Indoor Monitoring LED 1 The power indicator of the indoor unit LED 2 6 5 Network link LED, LED lights indicate that the device connected to the Ethernet. 1 4 1.
1.6 Wiring Diagram 1.4 Specifications of the Indoor Unit Display 304mm Intercom mode Conversation duration Up/+ Down/- Volume Monitoring Unlock Talk 197mm PAL/NTSC compatible Semi- Duplex communication 1A max. 1.5A max.
1.7 Note On Wiring Connection 1.8 Installation Process of Indoor Units 150-160cm The electric lock source camera is not include in the package, you can purchase an electric lock which is suitable for you need In the standard delivery the system supports locks with Normally Open (N.O.) door unlocking method. It means that in the normal state the dry contact is opened so the lock is kept under constant closed state.
◆ MONITORING 1.9 Operation Introduction Please be aware of Connection of 2 outdoor cameras to 1 indoor monitor is required for dual entrance monitoring at least. ◆ VISITOR CALL Standby mode Please be aware of Connection of 2 outdoor cameras is required. Standby mode The Visitor press the call button on outdoor camera 2 The Visitor press the call button on outdoor camera 1 Press the monitoring button on indoor monitor again display image from 1st outdoor camera on the screen.
◆ CALL TRANSFER TO OTHER EXTENSION 2. System Settings For Indoor Units At least 2 indoor units is required Outdoor camera call indoor monitor and conversation is underway Press this button to access Call transfer to other extension NOTICE: When you are transferring a call to other extension, the original conversation indoor unit will return to standby mode, and the indoor unit which the call is being transferred will also sound a continuous Ding Dong tone and the video image will appear on its screen.
Note: 1. If there is no “ ” button in the sub-menu, in order to for changes to sub-menu settings to take effect, it is necessary to return to the “save” menu to click “ ”. Changes to the sub-menu settings will not be saved if you do not click “ ” and exit the sub-menu immediately afterward. 2. If there is a “ ” button in the sub-menu, users need to click the “ ” button to save parameters in the current window. 2. When the selected files finish, the screen will return to the file list menu.
2.4.1.1 System-Basic 2.4.2 Network Move the cursor to the “Network” icon and left-click to enter the “Network” menu. Network setup includes: “Basic Setup”, “Port” and “Advanced”. Basic configure includes: “Language”, “Standard”, “Color Setup” and “Video margin”. [Standard]: From this field, select the system output type that is consistent with camera input, i.e. PAL or NTSC. [Language]: Use this field to change the language of the device menu text and the on-screen display.
[Media Port]: Port for the private protocol of the device and computer; the default is “9000”. If this port is being used by other server, use another free port for the device. [Web Port]: Sets up a Web browser port via HTTP. The default port number is “8090”, but the specific number is model-dependent. If Administrator changes the Web port, for example, “8088”, the port number should be added after the IP address, i.e. http://192.168.15.145:8088 should be entered as the IP address of the Web browser.
[Channel]: After clicking the “Channel” tab, users can modify the settings of the camera connected to the selected channel. Users can modify the parameters of each channel independently. [Frame rate]: For the PAL video output format, options include 5-25 frames. For the NTSC video output format, options include 5-30 frames. [Bit rate]: There are 5 options: 64K, 128K, 192K, 256K and 384K. [Bit rate control]: There are two modes for bit rate control: VBR and CBR .
Create a new root directory called “ivrupgrade” on a SD card, copy the update file to it, and then insert it into SD port of the device. Click “ ” to upgrade the firmware and it will display the process of the system upgrade. Note: The system upgrade will require at least two minutes; during this time, do not remove the SD card or turn the device disable. After completing the upgrade, the device will restart. 2.4.
2.4.9 Save/Exit On the “Configuration” menu, right-click or click “ ” to enter the “Save” menu. Set the appropriate settings for the ActiveX controls and plug-ins. Find the following controls in the “Security Settings” box and select the “Enable” option for each of them. This is an extremely important step. * Automatic prompting for ActiveX controls. * Binary and script behaviors. * Initialize and script ActiveX controls not marked as safe for scripting. * Download signed ActiveX controls.
Step 5: Examine the IP address, subnet mask, and default gateway on the PC. Step 6: Set the corresponding IP address, subnet mask, and default gateway on the indoor unit(for detailed instructions, refer to Section 2.4.2 Network Setup ). If the subnet mask and default gateway on the indoor unit are the same as those of the computer, then the IP address is most likely in the same network segment.
The left bottom corner of each individual channel is occupied by camera view tools: / / : Connect the current window view or close the current window view. ：Start recording or stop recording of the current channel view. And the right bottom corner of the current channel has a normal recording video symbol “ ”. ：Takes a snapshot of the displayed image. ：Increase or decrease brightness. ：Increase or decrease image contrast.
B Alarm Settings Double-click one of the listed recorded videos or select one of the listed recorded videos and then click “PLAY” to begin playback. From the sidebar on the left, click “Alarm Setting”, then select “Channel Alarm” to enter the “Channel Alarm” setup interface. From this interface, users can set motion-detection alarms, define motion-detection privacy masking areas, motion sensitivity, and record duration.
E IP Firewall From the sidebar on the left, click “Network Setting”, and then select ”IP Firewall” to enter the firewall settings interface. From this page, users can turn the firewall on or Disable for specific IP addresses. H. REMOTE UPGRADE From the sidebar on the left, click “REMOTE UPGRADE” to enter the remote upgrade interface. Clicking “ ” will select file for upgrading. Then click the “ ” remote upgrade button in the center of the screen. F System Setting I.
3.5.8 logout Click “Logout” to log out of the system. 4. Mobile Phone Software Visit This IP video door phone can transmit live feed to your mobile phone, so that you can have 'on the go' access to your surveillance system from virtually anywhere. To view, you must install a mobile operating system specific program into your mobile. Currently, there are a limited number of phones that are supported: Google Android and Apple iPhone or iPad.
Channel Number: Set the max channels of the device will be connected. Click “ ” to save. 2> After adding the device successfully, the device will appear on the main screen. Click the device, and all the channels of the device will be shown on the screen. Click any channel and it will connect immediately. The background of the channel will be highlighted after connecting successfully(shown as follows). mobile phone are both connected to internet.
2)Click the “MobileEyeDoor” icon to run the program, click “ ” to add a new device, first please choose the adding type, there are there methods to add device: “Two-dimensional Code Scanning”, “Manually enter” and “LAN Search”. Port: The mobile port of the indoor unit for remote access viewing via mobile phone, the default is “10510”. User: The user name set for entering the indoor unit system. (Admin by default) Password: The password set for entering the indoor unit system.
Channel Number: Set the max channels of the device will be connected. Click “ ” to save. 3) After adding the device successfully, the device will appear on the main screen. Click the device, and all the channels of the device will be shown on the screen. Click any channel and it will connect immediately. The background of the channel will be highlighted after connecting successfully(shown as follows). 7) Click “ ” to enter the snapshot and record file interface.
5.Right-click at blank, select “Use IE TAB Plus to play this Page”, and choose “Switch browser engine”. The indoor unit can now be connected successfully. 7. Click “Install' and the following screen will appear. Appendix 2. Accessing the indoor unit via Google Chrome 1.First, install Google Chrome on Windows(this manual will use Chrome version 7.0.517.36 as an example ). 2. After installing Google Chrome, search for the “IE TAB” Chrome add-on; this file is named “extension_1_4_30_4.crx”.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 10cm between the radiator & your body. FCC Warning This device complies with Part 15 of the FCC Rules.
