ASSEMBLE INSTRUCTION 10FT X 12FT ALUM DOUBLE ROOF GAZEBO
Safety Information WARNING: Keep all flame and heat sources away from this tent fabric. This tent is made with fabric that meets CPAI-84 specification for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistance properties ineffective.
Pre-Assembly PLANNING ASSEMBLY It will take at least two people about 90 minutes to complete the assembly process. A rubber mallet and a free standing ladder are needed during the process. IMPORTANT: Please count the number for each part before assembly. PART LIST NOTE: Parts not shown to actual size. ITEM DESCRIPTION QTY.
Pre-Assembly ITEM DESCRIPTION QTY. 4 II Roof Sheet 4 Support Arm 8 JJ Roof Sheet 6 EE Roof Sheet 2 KK Roof Sheet 4 FF Roof Sheet 2 LL Roof Sheet 4 GG Roof Sheet 2 MM Roof Mosquito Net 1 HH Roof Sheet 4 NN Mosquito Net 1 ITEM DESCRIPTION QTY. U U-Shaped Connector W ILLUSTRATION ILLUSTRATION Important: Do not remove the protective film from the roof sheets until you are ready to attach them to the frame in Step 17 & 22 .
Assembly 1. Attaching netting rails TT A TT A/B TT TT E E TT B TT TT TT E TT Attach one netting rail (E) to each cross beam (A) & (B) with self-tapping screws (TT) using Philips screw driver (XX). 2. Assembling cross beams QQ V QQ V A QQ V A/B QQ V QQ V B Attach two U-brackets (V) to the top of each cross beam (A) & (B) with bolts (QQ) using wrench (VV).
Assembly 3. Attaching netting rails TT C TT C/D TT TT F F TT TT D TT TT TT F Attach one netting rail (F) to each cross beam (C) & (D) with self-tapping screws (TT) using Philips screw driver (XX). 4 Assembling cross beams QQ V QQ V C QQ V C/D QQ V QQ V D Attach two U-brackets (V) to the top of each cross beam (C) & (D) with bolts (QQ) using wrench (VV).
Assembly 5. Assembling cross beams A U B A B A U B QQ Plug U-shaped connector (U) into each cross beam (B), using bolts (QQ) loosely secure them together until the end of this step. Repeat this for cross beam (A) until complete cross beams (A) & (B) are formed. Fully tighten all the bolts (QQ). 6. Assembling cross beams QQ C V D U QQ QQ V C V D C U D QQ Plug U-shaped connector (U) into each cross beam (D), using bolts (QQ) loosely secure them together until the end of this step.
Assembly 7. Erecting the main frame QQ D A C D A B B C QQ G A D QQ G G G G Stand the corner post (G) up. Attach the B side of the cross beam to the outside right corner of with corner post (G) and attach the A side of the cross beam to the outside left corner of with corner post (G) with bolts (QQ) using wrench (VV). 8. Attaching support arms W W W QQ W W W W QQ W W W Adjust corner post (G) upright.
Assembly 9. Assembling the roof frame H click! I H X H H I H I H H X I H Snap one corner roof tube (H) into each side receiver of the central support with connector (X) until you hear a click. Snap one roof tube (I) into each central receiver of the central support with connector (X) until you hear a click. 10.
Assembly 11. Attaching the roof sheet rails (J,K, L,M) L J M K J/L K/M M K J L L J CC H K M K QQ M J L Attach roof sheet rails (L) and (M) onto the corner roof tube (H) with washer plates (CC) and bolts (QQ) using wrench (VV).Do not fully tighten bolts until the end of step 24. Follow the above procedure to attach the roof sheet rails (J) and (K) onto the frame. 12.
Assembly 13. Assembling the small roof frame N click! O N X N O N N O X N N O N Snap one corner roof tube (N) into each side receiver of the central support with connector (X) until you hear a click. Snap one roof tube (O) into each central receiver of the central support with connector (X) until you hear a click. 14.
Assembly 15. Install washer plate I DD DD DD QQ As illustrated, install washer plate (DD) to roof tube (I) by using bolts (QQ). 16. Insert small support crossbar R R R R R R R R R R DD CC Insert small support crossbar with hook & loop (R) on pins of washer plates (CC) and (DD) as shown.
Assembly 17. Insert roof sheet for small roof O GG FF GG FF EE N EE FF GG GG EE EE Insert one piece of roof sheet (EE) into the groove of roof tubes as shown. IMPROTANT: Before insert next roof sheet you should finish till the step 19. The roof sheet should insert one by one. Suggest finish insert one side and then next side. 18.
Assembly 19. Attaching end cover for small roof OO PP OO OO PP OO OO SS PP SS Secure last assembly roof sheet (EE) by using corner end cover (OO) and side end cover (PP) with self-tapping screw (SS). In order not to damage inserts, do not over tighten the screws. Repeat step 17 to step 19 to finish insert all roof sheets (EE) (FF) (GG). 20.
Assembly 21. Attaching small support crossbars T T T T T T T T T T T CC T T T T T T T DD Insert small support crossbars (T) on pins of washer plate (CC) and (DD) as shown. 22. Attaching roof sheets HH LL KK II KK JJ JJ II HH LL JJ KK LL HH K KK JJ II JJ JJ II II KK LL HH Insert one piece of roof sheet (HH) into the groove of roof tubes as shown. IMPROTANT: Before insert next roof sheet (II) you should finish till the step 24. The roof sheet should insert one by one.
Assembly 23. Attaching roof rim LL S S H S S S S HH S S S S S S II S K S S S S JJ S S S S S S S S S As shown, insert roof rim (S) at the end of last assembly roof sheet rail. 24. Attaching end cover for big roof OO PP PP PP PP PP PP PP OO PP PP PP PP OO PP OO PP PP PP SS PP PP PP OO PP SS Secure last assembly roof sheet by using corner end cover (OO) and side end cover (PP) with self-tapping screw (SS).
Assembly 25. Assembling roof mosquito net R MM MM MM Z Z Loosen the hooks (Z). Fix roof mosquito net (MM) to the small roof. Tighten the hooks (Z) through the buttonhole on the roof mosquito net (MM). 26. Assembling mosquito net F NN G NN NN Hang up the mosquito net (NN) into the net hooks.
Assembly 27. Fix ground stakes G UU Use the ground stakes (UU) for ground fixing.