Installation Manual

ManualsBrandsLattice Semiconductor ManualsElectronics60GHz WirelessHD Display Mini Card Transmitter

Quick Start Guide

WirelessHD Application Controller

Introduction:

Congratulations on your purchase of this high quality laptop with integrated WirelessHD

transmitter, which represents the state of the art in 60GHz wireless video transmission giving

you complete freedom to enjoy displaying content from your laptop to a display such as a TV,

monitor, or projector without the limitations of cables.

The WirelessHD transmitter integrated into your laptop can provide a non line-of-sight

transmission range of up to 33 feet (10 m) to a WirelessHD receiver connected to an HDMI-

compatible display.

This Quick Start Guide provides the basic steps for making a wireless video connection from

your laptop with integrated WirelessHD transmitter to a TV, monitor or projector with a

connected WirelessHD receiver adapter.

Please refer to the documentation that came with your TV, WirelessHD receiver adapter, or

WirelessHD transmitter/receiver adapter pair for proper setup, configuration, and operation of

these devices.

Required Components:

1. A laptop with integrated WirelessHD transmitter

2. A WirelessHD receiver adapter connected to an HDMI-compatible TV or monitor

Please note that when you purchased your laptop with integrated WirelessHD transmitter, you

may have also purchased a kit containing a WirelessHD transmitter/receiver adapter pair.

Follow the instructions provided with that kit to properly connect the WirelessHD receiver

adapter to the TV, monitor, or projector.

First Time Connection:

Before attempting connection of your laptop with integrated WirelessHD transmitter to your

TV, monitor, or projector, please setup and configure the WirelessHD receiver adapter to the

TV, monitor, or projector according to the instructions provided with your WirelessHD receiver

adapter.

Summary of content (12 pages)

PAGE 1
Quick Start Guide WirelessHD Application Controller Introduction: Congratulations on your purchase of this high quality laptop with integrated WirelessHD transmitter, which represents the state of the art in 60GHz wireless video transmission giving you complete freedom to enjoy displaying content from your laptop to a display such as a TV, monitor, or projector without the limitations of cables.
PAGE 2
1. Turn on the TV, monitor, or projector and change the input to the HDMI port for which the WirelessHD receiver adapter is connected. 2. Turn on the WirelessHD receiver adapter. 3. Turn on and boot up your laptop system. 4. Launch the WirelessHD Application Controller software from either the Desktop shortcut icon: or from the Start/All Programs/WiHD Controller menu. 5. When the WirelessHD Application Controller software launches, you will see the following window: 6.
PAGE 3
enabled. 7. Click on the Network tab along the left hand side of the application. You will see a window like the following: The MAC address shown for the WVAN (wireless video area network) represents the WVAN ID that is provided from the receiver adapter which is connected to the TV, monitor, or projector. If the WirelessHD receiver adapter is turned on and there is not a MAC address that shows up in the WVAN list, press "Refresh List" to update the list.
PAGE 4
8. Select the WVAN ID and then press the "Connect" button as shown below: 9. Within 20 seconds, the notebook screen should be displayed on the TV, monitor, or projector. Note that " (Windows key) + P" keystroke allows selection of duplicate display mode (notebook display and external display contain the same content and resolution) or extended display mode (external display is an extension to the notebook display).
PAGE 5
10. The Status tab will reflect something similar as shown below upon a successful connection: Select different mode to other display screen: I. Power on TV/monitor (or other display products) and make sure WirelessHD receiver is activating. II. Open laptop WAC application III. Wait for the laptop and WirelessHD receiver to be associated. IV. Click “Connect” button on the WAC. V. Wait until the connection is successful. VI.
PAGE 6
Checkpoint: Extended Windows desktop should appear on laptop internal display and the TV/monitor. *The WirelessHD connection may be lost if display mode switching is too soon before it gets stabilized. OEM Installation Instructions for SIL-SK63100 Module Interference Statement USA - Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules.
PAGE 7
c. For minimum distance less than 3.9cm, the orientation of the RF chip shall be restricted to place the A1 marker located at the top. 4. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter within a host device, except in accordance with FCC multi-transmitter product procedures. Other antennas shall be installed with a minimum 20 cm separation from the 60 GHz device antenna.
PAGE 8
radiated power (EIRP) is not more than that required for successful communication. To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
PAGE 9
This equipment is marked with the symbol. This indicates compliance with the R&TTE Directive 1999/5/EC and meets the relevant parts of following technical specifications: EN 301 567 v1.1.1: Broadband Radio Access Networks (BRAN); 60 GHz Multiple-Gigabit WAS/RLAN Systems; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive. EN 301 489-28 v1.1.
PAGE 10
Belgium, Bulgaria, Croatia, Cyprus, Germany, Hungary, Iceland, Macedonia, Montenegro, Norway, Romania, Slovakia, Spain, Switzerland and United Kingdom. This device is restricted for use in the following countries: Denmark, Estonia, Finland, France, Latvia, Malta, Serbia and Slovenia. Note for system integrators: - The module is tested to comply with the requirement of the R&TTE Directive. System integrators are responsible for compliance of the final device with the R&TTE Directive.
PAGE 11
Proposed Label and Location Bottom of Module Label Location Proposed Label and Location for Host Device
PAGE 12
Additional Information Regarding WirelessHD: A product implementing WirelessHD is designed to wirelessly send fully uncompressed video up to 33 feet (10 m) non line-of-sight within the same room. Distances further than 33 feet (10 m) can be achieved when the transmitter and receiver are line-of-sight with each other.