SiBEAM Snap™ OEM Module Installation Guide for MOD6212/13
Module Installation Guide Introduction The Lattice Semiconductor MOD6212/13 Wireless module provides a data interface compatible with USB device, which allows reception/transmission of various data rate from/to any USB compliant device. OEM can develop a system equipped with this module to wirelessly connect their high data sources to the target device. The MOD6212/13 modules fit into a variety of industrial designs.
Module Installation Guide MOD6212/13 Transceiver Module Dimensions Figure 2. MOD6212/13 Transceiver Module Dimension (in mm) 3 ©2017 SiBEAM, Inc., a Lattice Semiconductor company. All rights reserved.
Module Installation Guide MOD6212/13 Transceiver Module Pinout Table 1. Signal pinout Pin Name Type Dir Group Description 1 2 3V3 SCL Power Digital Input In/Out O.D. Power I2C 3.3V +/-5% power supply I2C Clock, Tunneling port. SB6210/SB6212 Connect to Master; SB6211/SB6213 Connect to Slave 3 3V3 Power SDA Digital Input In/Out O.D. Power 4 3.3V +/-5% power supply I2C Data, Tunneling port.
Module Installation Guide MOD6212/13 Transceiver Module Connector The module is designed to be connected to the system board through a single board to board connector: On the module side: The connector type is DF40 from Hirose Part number: DF40C-30DP-0.4V (51) Description: Dual row Board to Board Receptacle (Plug), 0.4 pitch, 50 pins A=7.52mm, B=5.6mm, C =1.5mm Figure 3. Module side connector. 5 ©2017 SiBEAM, Inc., a Lattice Semiconductor company. All rights reserved.
Module Installation Guide MOD6212/13 Transceiver Module Functional description USB 3.0 Interface The MOD6212/13 Transceiver Module interfaces directly with a USB 3.0 port without requiring any additional control or interface logic. “ID_IN” and “ID_VAL” strapping pins on the Transceiver Module are used along with wireless communication to establish the USB port personality as either upstream facing or downstream facing.
Module Installation Guide SDA SDA SDA SK6210/12-MOD I2C Master SCL SK6211/13-MOD SCL SDA SDA SCL I2C Slave(s) SCL SCL I2C Slave(s) Figure 5. MOD6212/13 Transceiver Module I2C tunnel principle GPI, GPO, and LEDO The MOD6212/13 Transceiver Module contains a general purpose input (GPI) and a general purpose output (GPO) as well as a dedicated led output (LEDO) pin. At system level those can be routed to a Host MCU or directly to LED devices. The LEDO indicates the state of the wireless link.
Module Installation Guide I2C Master SDA SDA SCL SCL INT GPO MOD6212 MOD6213 SDA SDA SCL SCL I2C Slave(s) GPI INT WAKE_UP Figure 6. MOD6212/13 Transceiver Module interrupt based I2C tunnel Reset The MOD6212/13 Transceiver module has an RST input pin that keeps the device in standby. The reset circuit is designed such that if an RST signal is not available. The part will generate an internal RST signal as the device is powered on.
Module Installation Guide Modular approval for Lattice MOD6212/13 transmitter MOD6212/MOD6213 radio is a low power 60GHz full duplex radio operating under §15.255 that provides very short range (<15mm) contactless bidirectional USB data transfer between two hosts. Spatial separation between receive and transmit antennas is used to allow simultaneous operation of two radio links on the same frequency to provide bidirectional data transfer. Lattice is a module supplier and does not manufacture host systems.
Module Installation Guide FRONT ELEVATION outward facing open side direction of radiation AA MFC-VFBGA package Dimension A <= 3mm Host enclosure (insulating) Module PCB 10mm 10mm 26mm Inward facing shielded side Region with no metal permitted PLAN ELEVATION 2.5mm 2.5mm 5mm 2.5mm Figure 7: Module placement restrictions 10 ©2017 SiBEAM, Inc., a Lattice Semiconductor company. All rights reserved.
Module Installation Guide Proposed label 15mm Sibeam Snap Technology Transceiver module:MOD6212 R Lattice Semiconductor Corp. Made In China 204-630017 4mm FCC ID: UK2-MOD621X IC : 6705A-MOD621X 15mm Sibeam Snap Technology Transceiver module:MOD6213 R Lattice Semiconductor Corp. Made In China 204-630016 4mm FCC ID: UK2-MOD621X IC : 6705A-MOD621X Proposed Module Location 5.
Module Installation Guide Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Module Installation Guide This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT: In the user’s manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated.
Module Installation Guide 14 ©2017 SiBEAM, Inc., a Lattice Semiconductor company. All rights reserved.
Module Installation Guide Industry Canada Interference Statement This device complies with Industry Canada License-exempt RSS standard(s). Opération is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Module Installation Guide IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
