Rev.
Contents 1. What is SPDS? 3 2. Safety Information 4 3. Component Names 5 4. Specifications 6 5. Installation 7 6. Setting 8 ~ 10 · [IND] Danger / Caution Area Distance Setting 8 · [IND] Volume Control 8 · [IND] Restore Default Settings 8 · [IND] How to Set the Distance 9 · [PT] Alarm type Setting 10 · [PT] Volume Control 10 · [PT] How to Register Driver Tag 11 · [PT] How to Release Driver Tag 11 · [PT] How to Deactivate Driver Registration Function 11 7.
1. What is SPDS? Laserglow's SPDS is an intelligent proximity alert safety system that prevents collisions by alerting the operator of danger using 2 way communication to both drivers and pedestrians. This includes when a pedestrian approaches a vehicle or when a vehicle approaches another vehicle. It's easy to install without causing any damage to vehicles, and features industry leading proximity detection technology. > > Vehicle Tag(VT) Indicator "Watch Out.
2. Safety Information Caution! ※ Failure to observe the precautions in this manual may result in damage to the product or your property. 12/24 V DC Use only 12/24V DC. For vehicles with 36/48V DC, be sure to connect SMPS module to use DC 12/24V. Failure to do so will result in permanent damage. Do not place the product near flammable materials, stoves, candles, or fire.
3.
4. Specifications Specifications Vehicle Tag(VT) Indicator Pedestrian Tag(PT) Product Image Power Electrical Feature 12/24V DC Input(9/32Vdc) 12/24V DC Input(9/32Vdc) - Current 300mA 500mA - Interface CAN Bus 2.0 CAN Bus 2.
5. Installation Caution! It is highly recommended to install SPDS with the power off. Turn on the power after connecting all components. Open Wire Adapter Cable 5m Vehicle Tag(VT) or Cable Harness(6m) Indicator 3m Car Adapter * Normal operation: Green Flashes ON after turning on the power. * Caution! Fully tighten cable terminals to ensure proper connection and water-tight seal.
6. Setting - Indicator ※ Detailed setting of each function is available in SPDS Toolkit. (Please refer to SPDS Toolkit user manual) Danger / Caution Area Distance Setting ※ In a condition of normal operation Set the distance in order by following below 4 steps. Setting PT Danger Area ▶ Setting PT Caution Area ▶ Setting VT Danger Area ▶ Setting VT Caution Area ▶ Distance Setting Completed ③ Press STOP button to complete the PT Danger Area setting.
6. Setting - Indicator How to Set the Distance Distance setting can be set to even distance [2 / 4 / 6 / 8 / 10m] or odd distance [1 / 3 / 5 / 7 / 9m]. The default setting is even distance. SET 1 button : Distance -2 m STOP button : OK SET 2 button : Distance +2m 2m space per LED lamp [ ON OFF ] : 2m or 1m : 4m or 3m : 6m or 5m : 8m or 7m : 10m or 9m * To change to Odd distance [1 / 3 / 5 / 7 / 9m] : Press and hold SET 1 + STOP button at the same time. Eg.
6. Setting - Pedestrian Tags Alarm type Setting ① Press and hold the power button to turn on the power. (Charging is required if the red LED is on.) Press Power button 1 time > Sound Press Power button 1 more time > Vibration ④ Press and hold the menu button to complete the setup. Press Power button 1 more time > Sound + Vibration > (Sound + Vibration) ③ Press the power button to set the desired alarm type. ( Please refer to the alarm system below.
6. Setting - Pedestrian Tags (Driver Mode) Driver Mode is a function that deactivates PT of a driver who frequently drives vehicles. Prior to set the Driver Mode below, PC program "SPDS Toolkit" setting must be completed. How to Register Driver Tag ① Set the Driver Registration Function ON by using SPDS Toolkit. (Please refer to SPDS Toolkit User Manual for more details.) Registered. ② Once Driver Registration Function is completed, connect the indicator to the vehicle.
7. How to use VT Indicators that vehicle operator must know Situation LED Lamp Status When a pedestrian/vehicle approaches Caution Area When a pedestrian/vehicle approaches Danger Area Red / Green Light flashes gradually Alarm Mute Alarm Repeating "Watch Out" Repeating "Danger" Press STOP Button 1 Time Even if the alarm is OFF, the alarm will occur again when a pedestrian or other vehicle leaves the caution/ danger area and then re-enters.
7.
8. Troubleshooting Issue Access to PT MENU is unavailable. Reason You can access the menu after turning on the power. There is a red It is a signal indicating low voltage when the remaining battery power is less than 4 LED on the PT. hours. The volume of VT sound is too Indicator's volume setting is low. low. Can I mute the alarm when I Mute of alarm sound is possible. drive a vehicle with a PT? Can I pause an alarm to talk to It is possible to pause for 10 seconds.
WARRANTY Warranty Term 1 year from the purchase date Product Name Model Name Place of Purchase Date of Purchase Name of Customer Phone Number * Service information 1. If a performance or functional failure occurs from proper use during the warranty period, the repair service is free of charge. 2. When repair service is required, please present the warranty card with all information filled in. 3. The following cases will be charged for the repair regardless of warranty period.
T h i n k S m a rt , Work Sa fe Distributor * Contact distributor below for all inquiries about the purchased product: Laserglow Technologies 99 Ingram Dr Unit B, North York, ON M6M 2L7 North York, Toronto, ON Tel. (416) 729-7976 Fax. (480) 247-4864 E mail. sales@laserglow.com www.laserglow.