Assembly And Installation

ManualsBrandsLark Manor ManualsLantern Outdoor Wall LightingDrishya Textured Black 16.5'' H Seeded Glass Outdoor Wall Lantern with Dusk to Dawn

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

1. Energy saving fixture.

2. Use the dim-to-bright illumination option

where you want some minimum illumination

through out the night, such as at your front

entrance or garage door. Use the dark-to-bright

illumination option

where you do not need

minimum brightness, such

as the backyard

or back porch.

3. When in manual override mode, use wall switch

to keep the light ON till dawn.

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical codes,

it is recommended that you consult with a qualified

electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off the

wall switch is not sufficient to prevent an electrical shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

5. Do not attempt to take the lantern apart; there are no

serviceable parts inside.

6. To avoid sensor damage by lightning or electrical surge,

make sure the grounding wire is securely connected.

Maximum Wattage: 60W Incandescent Bulb

Work Temperature: - 4°F~104°F

Features

HARDWARE CONTENTS Note: Hardware not shown actual size.

Mounting Screw

Lock Nut

Ball Nut

Wire Connector

Rubber Pad

Cross Bar

Headless Screw

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

Page 1 of 6

Summary of content (6 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. Important to Know Features NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. WARNING • Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker). • Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge.
PAGE 3
ASSEMBLY INSTRUCTIONS (continued) 1. Thread two headless screws (DD) 1 through the cross bar (AA), and then secure them with four lock nuts (FF) (two on each side of the cross bar (AA). Adjust the length of the headless screws (DD) if necessary. Note: Make sure that the headless screws (DD) are lined up horizontally to make the fixture level. 2. Attach cross bar (AA) to outlet box using two mounting screws(BB). DD FF AA 2 AA BB 3. Pull out the source wires from the 3 AA outlet box.
PAGE 4
ASSEMBLY INSTRUCTIONS (continued) Step 1: Rotate the sensor lens counterclockwise to show up the adjustable knobs and slide switch. (See Fig.1) “TIME” Knob “LOW LEVEL” Knob “SENS” Knob Flathead Screwdriver (not included) TIME LOW LEVEL TEST OFF SENS PC AUTO Slide Switch Step 2: Use the small flathead screwdriver to adjust time, low level brightness and sensitivity. And slide the slide switch to choose desired mode. (See Fig.2 and Detail A view).
PAGE 5
FUNCTION AND OPERATION (continued) Customization Options Fig. 5 (View from back of sensor head) Shut-off Delay The Shut-off delay is the length of time the light will stay at highlevel brightness after motion has ceased to be detected. This Shut-off delay can be set when operation is in “OFF”, or “AUTO” mode by using the “TIME” knob located on the left side of the panel at the back of sensor head (See Fig.5) . To increase the shut-off delay, turn the knob clockwise.
PAGE 6
CARE AND MAINTENANCE Clean the glass and coated metal surfaces with a non-abrasive cleaner. Do not use any cleaners with chemicals, solvents or harsh abrasives, The motion detecting lens is coated with a specially painted finish and requires special care when cleaning. Use only a soft dry cloth to dust or wipe the lens area. TROUBLESHOOTING If the light does not work at all: 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring connection is correct. 3.