WCB1000H5PX/WCB1010H5PX User Manual V1.
Table of Contents Chapter 1. Before You Start ........................................................................................................... 1 1.1 Preface..................................................................................................................................... 1 1.2 Conventions ............................................................................................................................. 1 Chapter 2. System Overview ......................................
5.2.3 BRIDGE Setup.................................................................................................................... 66 5.3 Utilities.................................................................................................................................... 67 5.3.1 Profile Setting...................................................................................................................... 67 5.3.2 Firmware Upgrade ...........................................................
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Chapter 1. Before You Start 1.1 Preface The 802.11 b/g compliant WCB1000H5PX/WCB1010H5PX is an outdoor wireless device that can be used for three purposes. It can be deployed as a fixed Point to Point wireless base station between buildings, a bridge between LAN and wireless base station, or it can be used as a fixed wireless point to point between CPE and Internet Service Provider.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Chapter 2. System Overview 2.1 Introduction of WCB1000H5PX/WCB1010H5PX The 802.11 b/g compliant WCB1000H5PX/WCB1010H5PX is an outdoor wireless device that can be used for three purposes. It can be deployed as a outdoor fixed point to point between two building or between a building and wireless base station, or The fixed wireless point to point between CPE and Internet Service Provider.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 2.2 System Concept The WCB1000H5PX/WCB1010H5PX can be used in many applications with examples as follows: The Fixed point to point operation (connection between a building and a wireless base station). Bridge between LAN and wireless base station. The Fixed wireless point to point between CPE and Internet Service Provider. Note: The device shall be mounted on permanent structures.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 2.3 Product Benefit 500mW at 2.4GHz Output Power Topology : Point to Point; Operation Modes : Base station mode(Only point to point), Bridge mode (Bridge), CPE mode(Client Bridge) Multiple ESSIDs Capability VLAN tag over BRIDGE Supporting Qos & 802e WMM Business-class WLAN Security & Client Authentications Support 3 LEDs Wireless Signal Strength 2.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE General Base Station Features Number of ESSID : 8 Three mode : BASE STATION P to P Mode, BRIDGE Mode and CPE Mode Slot Time, ACK/CTS Timeout support RSSI threshold support TX burst support Beacon interval : adjustable to best adapt to the deployment environment IBSP : to facilitate faster roaming for the stations among different BASE STATION nearby 802.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Chapter 3. Base Installation 3.1 Hardware Installation 3.1.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 7. Ethernet : Green LED ON indicates connection, OFF indicates no connection 8. PoE Connector : For connecting to PSE 9. N-Type reverse Connector : For connecting to N-Type Female reverse connector WCB1010H5PX Front Panel 1. Rear Panel Reset Button : system reboot button press until LED flashed and release for system reboot or for reset to factory default press, LED flashes keep pressing until LED becomes static 2.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 3.1.3 Hardware Installation Steps Please follow the steps mentioned below to install the hardware of WCB1000H5PX/ WCB1010H5PX : Front Panel Rear Panel 1. Connect N-type reverse antenna to the N-type reverse connector on the rear panel. 2. Connect PSE to the PoE connector on the front panel. 3. Connect an Ethernet cable to the PSE and the other end to a computer. 4.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 3.2 Software Configuration 3.2.1 Instruction to Web Management Interface WCB1000H5PX/WCB1010H5PX supports web-based configuration. Upon the completion of hardware installation, WCB1000H5PX/WCB1010H5PX can be configured through a PC/NB by using its web browser such as Internet Explorer version 6.0. Default IP Address : 192.168.2.254 Default IP Netmask : 255.255.255.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE System Login The system manager Login Page then appears. Enter “admin” as User name and “default” as Password, and then click OK to login to the system. Login Success System Overview page will appear after successful login.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 3.2.2 Quick Configuration WCB1000H5PX/WCB1010H5PX is a three mode system which can be configured either as a gateway or an base station as desired. This section provides a step-by-step configuration procedure for basic installation of BASE STATION Mode, BRIDGE Mode and CPE Mode. B 3.2.2.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Step 2 : Change Password Click System -> Management and then Admin Configuration page appears. Enter a new password, and verify it again in the New Password and Check New Password field respectively. Click Save button, and process with steps followed. Step 3 : LAN IP Settings Click System -> LAN, and then Network Setup page appears.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Step 4 : Time Zone settings Click System -> Time Server, and then Time Server Setup page appears. Enable “Setup Time Use NTP”, and then enter the related information. Click Save button to save the settings. Step 5 : ESSID Settings Click Wireless -> Virtual BASE STATION Setup, and then VBS Setup page appears.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE VBS BS00 Setup broadcast ESSID for easy identification of system when device is trying to associate with service. Click Save button to save settings Step 6 : Security Settings In VBS0 Configuration page, select WEP in “Security Type“ pull down menu. The WEP setting field will show up immediately.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 3.2.2.2 BRIDGE Mode Step 1 : Mode Confirmation Ensure the Operating Mode is currently at BRIDGE mode; the web management UI can be viewed at the Status section under the System Overview page. Bridge List B Step 2 : Change Password Click System -> Management and then Admin Configuration page appears. Enter a new password, and verify it again in the New Password and Check New Password field respectively.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Step 3 : LAN IP Settings Click System -> LAN, and then Network Setup page appears. Enable “Static IP” and “DNS”, and enter the related information in the field marked with red asterisks. Click Save button to save the settings. Step 4 : Time Zone settings Click System -> Time Server, and then Time Server Setup page appears. Enable “Setup Time Use NTP”, and then enter the related information. Click Save button to save the settings.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Step 5 : Enable BRIDGE Peer's MAC Address Click Wireless -> BRIDGE Setup, and then BRIDGE Setup page appears. BRIDGE Bridge Setup BRIDGE Enable “BRIDGE Peer's MAC Address”, and then enter the related information. Click Save button to save the settings. Step 6 : Wireless General Settings Click Wireless -> General Setup, and then General Setup page appears.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 3.2.2.3 CPE Mode Step 1 : Mode Confirmation Ensure the Operating Mode is currently at CPE mode; the web management UI can be viewed at the Status section under the System Overview page. Step 2 : Change Password Click System -> Management and then Admin Configuration page appears. Enter a new password, and verify it again in the New Password and Check New Password field respectively.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Step 3 : Site Survey Click Wireless -> Site Survey, and then CPE Site Survey page appears. The system will automatically scan and display the scan results on all BASE STATION existing near by the system. Note : The scan result displayed here is an example only.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE BS00 Step 6 : WAN Settings Click System -> WAN, and then WAN Setup page appears. Enable “Static IP”, and then enter the related information. Click Save button to save the settings. (Default WAN IP is 192.168.1.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Step 7 : LAN Settings Click System -> LAN, and then LAN Setup page appears. Enter the “IP Address” and “IP Netmask” of the LAN Setup. Step 8 : Time Zone settings Click System -> Time Server, and then Time Server Setup page appears. Enable “Setup Time Use NTP”, and then enter the related information. Click Save button to save the settings. Click Reboot button to activate all settings configured so far.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Chapter 4. BASE STATION (Point to Point) Mode Configuration When BASE STATION mode is activated, the system can be configured as an Base station. This section provides information in configuring the BASE STATION mode with graphical illustrations. WCB1000H5PX/WCB1010H5PX provides functions as stated below where they can be configured via a user-friendly web based interface.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.1 System This section provides information in configuring the following functions: Operating Mode, LAN Setup, Management, Time Server, SNMP Setup BS mode B mode 4.1.1 Operating Mode WCB1000H5PX/WCB1010H5PX supports three operation modes; BASE STATION mode , BRIDGE mode and CPE mode. The administrator can set the desired mode via this page, and then configure the system according to their deployment needs.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.1.2 LAN Setup Here is the instruction for how to setup the local IP Address and Netmask. Please click on System -> LAN and follow the below setting. Mode : Check either “Static IP” or “Dynamic IP” button as desired to set up the system IP of LAN port . Static IP : The administrator can manually setup the LAN IP address when static IP is available/ preferred.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Primary : The IP address of the primary DNS server. Secondary : The IP address of the secondary DNS server. Spanning Tree Protocol The spanning tree network protocol provides a loop free topology for any bridged LAN. The Spanning Tree Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d. Change these settings as described here and click Save button to save your changes.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.1.3 Management The administrator can later obtain the geographical location of the system via the information configured here. The administrator also can change system password and configure system login methods. Please click System -> Management and follow the below settings. System Information System Name : Enter a desired name or use the default provided.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Admin Login Methods : The admin manager can enable or disable system login methods, it also can change services port. Click Save button to activate the admin login methods.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.1.4 Time Server System time can be configured via this page where manual setting and NTP server configuration are both supported. Please click on System -> Time Server and follow the below setting. Local Time : Display the current time of the system. Setup Time Use NTP : Enable Network Time Protocol, NTP, to synchronize the system time with NTP server. Default NTP Server : Select the NTP Server from the drop-down list.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.1.5 SNMP Setup SNMP is an application-layer protocol that provides a message of format for communication between SNMP managers and agents. By enabling SNMP function, the administrator can obtain the system information remotely. Please click on System -> SNMP Setup and follow the below setting. v2c : Check v2c button to activate SNMP v2c agent or unchecked to deactivate this function.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE information. SNMP rw password : Enter the password that allows read/write access to the system's SNMP information. SNMP Trap : Events on cold start, interface up & down, and association & disassociation can be reported via this function to an assigned server. Community : Enter the community strings required by the remote host computer that will receive trap messages or notices send by the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.2 Wireless The system manager can configure related wireless settings, General Settings, Advanced Settings, Virtual BASE STATION Setting, Security Settings, and Access Control Settings.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.2.1 General Setup The administrator can change the data transmission, channel and output power settings for the system. Please click on Wireless -> General Setup and follow the below setting. Virtual BS mode MAC address : The MAC address of the Wireless interface is displayed here. Band Mode : Select an appropriate wireless band; bands available are 801.11b, 802.11g and 802.11b+802.11g.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.2.2 Advanced Setup The administrator can change the Slot Time, ACK/CTS Timeout, RTS threshold and fragmentation threshold settings for the system. Please click on Wireless -> Advanced Setup and follow the below setting. Virtual BS mode Slot Time : Enter the desired slot time for the BASE STATION. ACK Timeout : The time interval for waiting the “ ACKnowledgment frame”.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE DTIM Interval : Input the DTIM Interval that is generated within the periodic beacon at a specified frequency. Higher DTIM will let the wireless client save energy more, but the throughput will be growing worse. Fragment Threshold : The value specifies the maximum size of packet allowed before data is fragmented into multiple packets. Please use this value to tune the wireless connection if lots of retransmission happens.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.2.3 Virtual BASE STATION Setup The administrator can create Virtual BASE STATION via this page. Please click on Wireless -> Virtual BS STATION Setup and follow the below setting.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.2.3.1 Virtual BASE STATION General Configuration For each Virtual BASE STATION, administrators can configure general settings and wireless security type. Click Wireless -> Virtual BASE STATION -> EDIT, and then Virtual BASE STATION Configuration page appears. VBS 0 BS00 ESSID : Extended Service Set ID indicates the SSID which the clients used to connect to the VBS.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Security Type : Select the desired security type from the drop-down list; the options are WEP, WPA-PSK, WPA2-PSK, WPA-Enterprise, WPA2-Enterprise and 802.1X. Disable : Data are unencrypted during transmission when this option is selected. WEP : WEP, Wired Equivalent Privacy, is a data encryption mechanism based on a 64-bit, 128-bit or 152bit shared key. Select WEP as the security type from the drop down list as desired.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE WPA-PSK (or WPA2-PSK) : WPA (or WPA2) Algorithms, allows the system accessing the network by using the WPA-PSK protected access. Cipher Suite : Check on the respected button to enable either AES or TKIP cipher suites; default is TKIP. Group Key Update Period : This time interval for re-keying GTK (broadcast/multicast encryption keys) in seconds. Enter the time-length required; the default time is 600 seconds.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE WPA-Enterprise (or WPA2-Enterprise): The RADIUS authentication and encryption will be both enabled if this selected. WPA General Settings : • Cipher Suite : Check on the respected button to enable either AES or TKIP cipher suites. • Group Key Update Period : This time interval for re-keying GTK (broadcast/ multicast encryption keys) in seconds. Enter the time-length required; the default time is 600 seconds.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Accounting Server Settings : • Accounting Server : Enter the IP address of the Accounting RADIUS server. • Port : The port number used by Accounting RADIUS server. Use the default 1813 or enter port number specified. • Shared Secret : The secret key for system to communicate with Accounting RADIUS server. Support 1 to 64 characters. 802.1X : When 802.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Authentication RADIUS Server Settings : • Authentication Server : Enter the IP address of the Authentication RADIUS server. • Port : The port number used by Authentication RADIUS server. Use the default 1812 or enter port number specified. • Shared secret : The secret key for system to communicate with Authentication RADIUS server. Support 1 to 64 characters.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.2.3.2 Virtual BS Access Control List (ACL) Setup In this function, the administrator can be allow or reject clients to access Virtual BS. Please click on Wireless -> Virtual BS Setup -> ACL Setup and follow the below setting. Access Control Type : Select the desired access control type from the drop-down list; the options are Disable, Allow or Reject. MAC Address : Enter MAC address in this field.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.3 Utilities The administrator can maintain the system via this page: Profile Setting, System Upgrade, Ping Utility, and Reboot. 4.3.1 Profile Setting Current settings on the system can be backed up, or previous backed up settings can be restored as well as resetting the system back to factory default can be performed via this page. Please click on Utilities -> Profile Setting and follow the below setting.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.3.2 Firmware Upgrade To upgrade the system firmware, click Browse to search for the new firmware file, and then click Upgrade button to execute the upgrade process. Note : 1. To prevent data loss during firmware upgrade, please back up the current settings before proceeding to firmware upgrade. 2. Please restart the system after the upgrade. Do not interrupt the system, i.e.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.3.3 Ping Utility The administrator can diagnose the network connectivity via this function. Please click on Utilities -> Ping Utility and follow the below setting. IP/Domain : Enter the desired domain name or IP address of the target device for diagnosis purpose, i.e. www.google.com, and click ping button to proceed. The ping result will be shown in the Result field.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.3.4 Reboot This function allows the administrator to safely restart the WCB1000H5PX/WCB1010H5PX. Click Reboot to restart the system immediately, and the whole process will take about three minutes to complete. The Restart page as displayed below appears during the rebooting period. If turning off the power is necessary, please allow the restart process to be completed before turning off the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.4 Status Information of the current system settings can be reviewed via this page; statuses of Overview, Clients, and Event Log are displayed in this interface.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.4.1 Overview Detailed information on System, LAN Information, and Wireless Information can be reviewed via this page. System : Display the information of the system. BS Mode System Name : The name of the system. Operating Mode : The mode currently in service. Firmware Version : The current firmware version installed. Firmware Date : The build time of the firmware installed.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE MAC Address : The MAC address of the LAN port. Mode : The current mode of the LAN port. IP Address : The IP address of the LAN port. IP Netmask : The IP netmask of the LAN port. IP Gateway : The gateway IP address of the LAN port. Primary DNS : The current primary DNS server of the system. Secondary DNS : The current secondary DNS server of the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.4.2 Client The administrator can obtain detailed Information such as VBS, ESSID, MAC Address, RSSI, and Idle Time of all associated clients via this page. BS : Virtual BS which the device is associated with. ESSID : ESSID which the device is associated with. RSSI : Indicate the RSSI of the respective client's association. Idle Time : Time period that the associated client is inactive (units in seconds).
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 4.4.3 Event Log The reported system events can be reviewed here. Date/ Time: The date and time when the event occurred. Hostname: The name of the host which records the event. It helps the administrator identify the source of the reported events. Process name (with square brackets): Indicate the process with which the specific event is associated. Description: Description of the event.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Chapter 5. BRIDGE Mode Configuration When BRIDGE mode is activated, the system can be configured as a repeater or client bridge. This section provides information in configuring the BRIDGE mode with graphical illustrations. WCB1000H5PX/WCB1010H5PX provides functions as stated below where they can be configured via a user-friendly web based interface.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.1 System This section provides information in configuring the following functions: Operating Mode, LAN Setup, Management, Time Server, SNMP Setup BS Mode B Mode 5.1.1 Operating Mode WCB1000H5PX/WCB1010H5PX supports three operation modes; BS mode, BRIDGE mode and CPE mode. The administrator can set the desired mode via this page, and then configure the system according to their deployment needs.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.1.2 LAN Setup Here is instruction for how to setup the local IP Address and Netmask. Please click on System -> LAN and follow the below setting. Mode : Check either “Static IP” or “Dynamic IP” button as desired to set up the system IP of LAN port . Static IP : The administrator can manually setup the LAN IP address when static IP is available/ preferred.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Primary : The IP address of the primary DNS server. Secondary : The IP address of the secondary DNS server. Spanning Tree Protocol The spanning tree network protocol provides a loop free topology for any bridged LAN. The Spanning Tree Protocol, which is also referred to as STP, is defined in the IEEE Standard 802.1d. Change these settings as described here and click Save button to save your changes.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.1.3 Management The administrator can later obtain the geographical location of the system via the information configured here. The administrator also can change system password and configure system login methods. Please click System -> Management and follow the below settings. System Information System Name : Enter a desired name or use the default provided.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Admin Login Methods : The admin manager can enable or disable system login methods, it also can change services port. Click Save button to activate the admin login methods.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.1.4 Time Server System time can be configured via this page where manual setting and NTP server configuration are both supported. Please click on System -> Time Server and follow the below setting. Local Time : Display the current time of the system. Setup Time Use NTP : Enable Network Time Protocol, NTP, to synchronize the system time with NTP server. Default NTP Server : Select the NTP Server from the drop-down list.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.1.5 SNMP Setup SNMP is an application-layer protocol that provides a message of format for communication between SNMP managers and agents. By enabling SNMP function, the administrator can obtain the system information remotely. Please click on System -> SNMP Setup and follow the below setting. v2c : Check v2c button to activate SNMP v2c agent or unchecked to deactivate this function.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE information. SNMP rw password : Enter the password that allows read/write access to the system's SNMP information. SNMP Trap : Events on cold start, interface up & down, and association & disassociation can be reported via this function to an assigned server. Community : Enter the community strings required by the remote host computer that will receive trap messages or notices send by the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.2 Wireless The system manager can configure related wireless settings, General Setup, Advanced Setup, BRIDGE Setup.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.2.1 General Setup The administrator can change the data transmission, channel and output power settings for the system. Please click on Wireless -> General Setup and follow the below setting. Bridge Setup MAC address : The MAC address of the Wireless interface is displayed here. Band Mode : Select an appropriate wireless band; bands available are 801.11b, 802.11g and 802.11b+802.11g.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.2.2 Advanced Setup The administrator can change the Slot Time, ACK/CTS Timeout, RTS threshold and fragmentation threshold settings for the system. Please click on Wireless -> Advanced Setup and follow the below setting. Bridge Setup Slot Time : Enter the desired slot time for the BRIDGE. ACK Timeout : The time interval for waiting the “ ACKnowledgment frame”.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Fragment Threshold : The value specifies the maximum size of packet allowed before data is fragmented into multiple packets. Please use this value to tune the wireless connection if lots of retransmission happens. Enter a value ranging from 256 to 2346. RTS Threshold : Tuning the Request to Send, RTS threshold will help the system control its access to medium and alleviate the hidden node problem.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.2.3 BRIDGE Setup The administrator can create BRIDGE Links via this page. Please click on Wireless -> BRIDGE Setup and follow the below setting. Bridge Setup Bridge Setup Bridge WMM : Select Enable, the packets with QoS WMM will has higher priority.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.3 Utilities The administrator can maintain the system via this page: Profile Setting, System Upgrade, Ping Utility, and Reboot. 5.3. 1 Profile Setting Current settings on the system can be backed up, or previous backed up settings can be restored as well as resetting the system back to factory default can be performed via this page. Please click on Utilities -> Profile Setting and follow the below setting.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.3.2 Firmware Upgrade To upgrade the system firmware, click Browse to search for the new firmware file, and then click Upgrade button to execute the upgrade process. Note : 1. To prevent data loss during firmware upgrade, please back up the current settings before proceeding to firmware upgrade. 2. Please restart the system after the upgrade. Do not interrupt the system, i.e.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.3.3 Ping Utility The administrator can diagnose the network connectivity via this function. IP/Domain : Enter the desired domain name or IP address of the target device for diagnosis purpose, i.e. www.google.com, and click ping button to proceed. The ping result will be shown in the Result field. Time : Enter the time for ping utility; default is 5, maximum is 50.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.3.4 Reboot This function allows the administrator to safely restart the WCB1000H5PX/WCB1010H5PX. Click Reboot to restart the system immediately, and the whole process will take about three minutes to complete. The Restart page as displayed below appears during the rebooting period. If turning off the power is necessary, please allow the restart process to be completed before turning off the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.4 Status Information of current system settings can be over viewed via this page; statuses of Overview, BRIDGE List, and Event Log are displayed in this interface.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.4.1 Overview Detailed information on System and LAN Information can be reviewed via this page. System : Display the information of the system. System Name : The name of the system. Operating Mode : The mode currently in service. Firmware Version : The current firmware version installed. Firmware Date : The build time of the firmware installed.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE MAC Address : The MAC address of the LAN port. Mode : The current mode of the LAN port. IP Address : The IP address of the LAN port. IP Netmask : The IP netmask of the LAN port. IP Gateway : The gateway IP address of the LAN port. Primary DNS : The current primary DNS server of the system. Secondary DNS : The current secondary DNS server of the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.4.2 BRIDGE List The administrator can obtain detailed Information such as BRIDGE, Status, MAC Address, RSSI, and Last Tx Time of all BRIDGE link via this page. Bridge Link Status Bridge Link Status BRIDGE : BRIDGE which the device is linked with. Status : Display BRIDGE status. MAC address : Display MAC address of BRIDGE peer. RSSI : Indicate the RSSI of the respective BRIDGE linked.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 5.4.3 Event Log The reported system events can be reviewed here. Date/ Time: The date and time when the event occurred. Hostname: The name of the host which records the event. It helps the administrator identify the source of the reported events. Process name (with square brackets): Indicate the process with which the specific event is associated. Description: Description of the event.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Chapter 6. CPE Mode Configuration When CPE mode is activated, the system can be configured as a CPE. This section provides information in configuring the CPE mode with graphical illustrations. WCB1000H5PX/WCB1010H5PX provides functions as stated below where they can be configured via a user-friendly web based interface.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.1 System This section provides information in configuring the following functions: Operating Mode, WAN Setup, LAN Setup, Management, Time Server, SNMP Setup BS Mode B Mode 6.1.1 Operating Mode WCB1000H5PX/WCB1010H5PX supports three operation modes; BS mode , BRIDGE mode and CPE mode. The administrator can set the desired mode via this page, and then configure the system according to their deployment needs.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.1.2 WAN Setup Here is instruction for how to setup the WAN. Please click on System -> WAN and follow the below setting. Mode : Check “Static IP”, “Dynamic IP” and “PPPoE” button as desired to set up the system IP of WAN port. Static IP : The administrator can manually setup the WAN IP address when static IP is available/ preferred.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Dynamic IP : This configuration type is applicable when the WCB1000H5PX/ WCB1010H5PX is connected to a network with the presence of a DHCP server; all related IP information will be provided by the DHCP server automatically. If the IP Address do not assigned from DHCP server, the system need manual connect to DHCP server. Please refer to Section 6.6.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE DNS : Check either “No Default DNS Server” or “Specify DNS Server IP” button as desired to set up the system DNS. Primary : The IP address of the primary DNS server. Secondary : The IP address of the secondary DNS server. Bandwidth : The administrator can control download and upload of bandwidth.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Note : The Clone MAC Address field will display MAC address of the PC you are connected with the system currently. Manual Address : Enter the MAC address registered with your ISP. Change these settings as described here and click Save button to save your changes.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.1.3 LAN Setup Here is instruction for how to setup the local IP Address and Netmask. Please click on System -> LAN and follow the below setting. LAN IP : The administrator can manually setup the LAN IP address. IP Address : The IP address of the LAN port; default IP address is 192.168.2.254 IP Netmask : The Subnet mask of the LAN port; default Netmask is 255.255.255.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Check Enable button to activate this function or Disable to deactivate this service. DHCP : Start IP / End IP: Specify the range of IP addresses to be used by the DHCP server when assigning IP address to clients. DNS1 IP : Enter IP address of the first DNS server; this field is required. DNS2 IP : Enter IP address of the second DNS server; this is optional.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.1.4 Management The administrator can later obtain the geographical location of the system via the information configured here. The administrator also can change system password and configure system login methods. Please click System -> Management and follow the below settings. System Information System Name : Enter a desired name or use the default provided.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Admin Login Methods : The admin manager can enable or disable system login methods, it also can change services port. Click Save button to activate the admin login methods.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.1.5 Time Server System time can be configured via this page where manual setting and NTP server configuration are both supported. Local Time : Display the current time of the system. Setup Time Use NTP : Enable Network Time Protocol, NTP, to synchronize the system time with NTP server. Default NTP Server : Select the NTP Server from the drop-down list.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.1.6 SNMP Setup SNMP is an application-layer protocol that provides a message of format for communication between SNMP managers and agents. By enabling SNMP function, the administrator can obtain the system information remotely. v 2 c : C h e ck v 2 c b utton to activate SNMP v2c agent or unchecked to deactivate this function.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE information. SNMP ro password : Enter the password that allows read-only access to the system's SNMP information. SNMP rw user : Enter the community strings that allows read/write access to the system's SNMP information. SNMP rw password : Enter the password that allows read/write access to the system's SNMP information.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.2 Wireless This section will guide users through wireless setting for WCB1000H5PX/WCB1010H5PX to associate with its up link BS.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.2.1 General Setup The administrator can change the data transmission, channel and output power settings for the system. Please click on Wireless -> General Setup and follow the below setting. ESSID : Assign Service Set ID for the wireless system. Band Mode : Select an appropriate wireless band; bands available are 801.11b, 802.11g and 802.11b+802.11g.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Key Length : Select the desire option are 64 bits, 128 bits or 152 bits from drop-down list. WEP auth Method : Enable the desire option among Open system or Shared. WEP Key # : Select key index is used to designate the WEP key during data transmission. Enter HEX format WEP key value; the system support up to 4 sets of WEP keys.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.2.2 Advanced Setup The administrator can change the Slot Time, ACK/CTS Timeout, RTS threshold and fragmentation threshold settings for the system. Please click on Wireless -> Advanced Setup and follow the below setting. Slot Time : Enter the desired slot time for the BRIDGE. ACK Timeout : The time interval for waiting the “ ACKnowledgment frame”.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.2.3 Site Survey Base station located around the system can be found via the scan function. The administrator can then select a desired BS to be associated with via this page. Please click on Wireless -> Site Survey. SSID : Service Set ID of the BS or repeater found around the system. MAC Address : MAC address of the respected BS. Channel : The channel number currently used by the respective BS.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.3 Firewall Current firewall functions supported are IP filter and MAC filter. The system's firewall enhances the security of your network, you can also enable a variety of filters to further protect your network.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.3.1 IP Rule Setup The administrator can setting IP Filter via this page, Please click on Firewall -> IP Rule Setup and follow the below setting. Source Address/Mask : Enter the desired source IP address and netmask; the mask must be a plain number, i.e. 192.168.2.10/32 Source Port : The source port(s) required for this rule.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Reset : Click Reset button to clear configuration field. There are 20 rules maximum allowed in this list. Del : Click Del to remove desired rule. Edit : Click Edit to edit desired rule. Click Reboot button to activate your changes.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.3.2 MAC Rule Setup The administrator can setting MAC Filter via this page, Please click on Firewall -> MAC Rule Setup and follow the below setting. Action : Select the desired access control rule from the drop-down list; the options are Disable, Deny All and Allow All. MAC Address : Enter MAC address in this field. There are 20 rules maximum allowed in this MAC address list.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.4 NAT Current NAT functions supported are IP/ Port forwarding and DMZ, Demilitarized Zone. The administrator can open a certain area in the network to the Internet for limited and controlled access for special purpose such as gaming server or conferencing center.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.4.1 Virtual Server (IP/ Port Forwarding) A certain area in the network can be exposed to the Internet in a limited and controlled way for on-line game or video conferencing via this page. Please ensure the internal port to be used is not occupied by other applications. Please click on NAT -> Virtual Server and follow the below setting. Virtual Server : Check Enable button to activate this rule, and Disable to deactivate.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Save : Click Save button to activate the new creation. Reset : Click Reset button to clear configuration field. There are 20 rules maximum allowed in this Virtual Server Rule List Del : Click Del to remove desired rule. Edit : Click Edit to edit desired rule. Click Reboot button to activate your changes.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.4.2 DMZ The Demilitarized Zone, DMZ, allows a computer or server to be exposed to the Internet for special purpose, i.e. a web server, where external users can access the location without authentication. Please click on NAT -> DMZ and follow the below setting. DMZ : Check Enable button to activate this function, and Disable to deactivate.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.5 Utilities The administrator can maintain the system via this page: Profile Setting, System Upgrade, Ping Utility, and Reboot. 6.5.1 Profile Setting Current settings on the system can be backed up, or previous backed up settings can be restored as well as resetting the system back to factory default can be performed via this page. Please click on Utilities -> Profile Setting and follow the below setting.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.5.2 Firmware Upgrade To upgrade the system firmware, click Browse to search for the new firmware file, and then click Upgrade button to execute the upgrade process. Note : 1. To prevent data loss during firmware upgrade, please back up the current settings before proceeding to firmware upgrade. 2. Please restart the system after the upgrade. Do not interrupt the system, i.e.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.5.3 Ping Utility The administrator can diagnose the network connectivity via this function. IP/Domain : Enter the desired domain name or IP address of the target device for diagnosis purpose, i.e. www.google.com, and click ping button to proceed. The ping result will be shown in the Result field. Time : Enter the time for ping utility; default is 5, maximum is 50.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.5.4 Reboot This function allows the administrator to safely restart the WCB1000H5PX/WCB1010H5PX. Click Reboot to restart the system immediately, and the whole process will take about three minutes to complete. The Restart page as displayed below appears during the rebooting period. If turning off the power is necessary, please allow the restart process to be completed before turning off the system.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.6 Status Information of current system settings can be over viewed via this page; statuses of Overview, DHCP Clients, and Event Log are displayed in this interface.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.6.1 Overview Detailed information on System, WAN Information, CPE Wireless Information and LAN Information can be reviewed via this page. System : Display the information of the system. System Name : The name of the system. Operating Mode : The mode currently in service. Firmware Version : The current firmware version installed. Firmware Date : The build time of the firmware installed.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Mode : The current mode of the WAN port. Note : The WAN port specified Dynamic IP, and the Release and Renew button will be show up. The WAN port specified PPPoE, and the Connect and Disconnect button will be show up. Dynamic IP : Click Release button to release IP address of WAN port, Renew button to renew IP address through DHCP server. PPPoE : Click Connect button to assigned IP address from PPPoE server.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE ESSID : Display Extended Service Set ID of the wireless currently. Security : Display security type of the wireless currently. Status : Display connection status of the wireless currently. If the system associate with BS, the BSSID, RSSI and Last Tx Time will be show up. BSSID : Indicate the Basic Service Set ID of the associated BS RSSI : Indicate the RSSI of the associated BS.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.6.2 DHCP Clients The administrator can obtain DHCP client's IP/MAC address via this page. IP : The IP address assigned by DHCP server to the specific LAN device. MAC address : The MAC address of the LAN device.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 6.6.3 Event Log The reported system events can be reviewed here. Date/ Time: The date and time when the event occurred. Hostname: The name of the host which records the event. It helps the administrator identify the source of the reported events. Process name (with square brackets): Indicate the process with which the specific event is associated. Description: Description of the event.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 7. Command Line Interface(CLI) The administrator can be used help, showinfo, pwinfo, set, reboot, default and password functions from Telnet session. 7.1 Accessing the CLI with Telnet Follow these steps to access the CLI with Telnet of Windows XP. 1. Click Start -> Run, and type “cmd” in the “Run” window. The command window appears. 2. Enter “telnet 192.168.2.254” to connect with system. 3.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 7.2 Using the CLI After accessing the CLI, the administrator can use command on the system. Command Description help Display all commands description show info Display System and LAN information pwinfo Wireless Information Display Utility set Configure LAN IP address, netmask, gateway, and system mode.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE BRIDGE Mode : Enable all of BRIDGE link, the Choose Device window will be display wds0 to wds7. Enter the desired device, the window will be display result. CPE Mode : The Choose Device window only display ath0. Click Enter, the window will be display result. 'Q'uit : Type Q to close this utility. 'W'ireless : Type W to open Choose Device window. 'S'ignal : Type S to open Peer MAC Address window.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Using : The used device of system currently. Watching : The MAC address of specified peer currently. Signal : Indicate signal strength of specified peer currently. S'T'op-Signal : Type T to stop display signal strength. 'P'ing : Type P to open “Ping” window. Destination : Enter the specify destination. Specify Packet Size : Enter specify packet size.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Appendix A. Windows TCP/IP Settings Windows XP 1. Click Start -> Settings -> Control Panel, and then “Control Panel” window appears. Click on “Network Connections”, and then “Network Connections” window appears. 2. Click right on “Local Area Connection”, and select Properties.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE 3. In “Local Area Connection Properties” window, select “Internet Protocol (TCP/IP)” and click on Properties button. 4. Select “Use the following IP address”, and type in IP address : 192.168.2.100 Subnet mask : 255.255.255.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Appendix B. Table C Valid Characters when using WMI Valid Characters for using WMI Block Field Valid Characters LAN IP Address IP Format; 1-254 IP Netmask 128.0.0.0 ~ 255.255.255.252 IP Gateway IP Format; 1-254 Primary IP Format; 1-254 Secondary IP Format; 1-254 Hostname Length : 32 0-9, A-Z, a-z @-_. Manual MAC Address 12 HEX chars IP Address IP Format; 1-254 IP Netmask 128.0.0.0 ~ 255.255.255.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Table C Valid Characters for using WMI (continued) Block Field Valid Characters Management System Name Length : 32 0-9, A-Z, a-z ~!@#$%^*()_+-{}|:<>?[]/;`, .= Description Length : 32 0-9, A-Z, a-z Space ~!@#$%^*()_+-{}|:<>?[]/;`, .= Location Length : 32 0-9, A-Z, a-z ~!@#$%^*()_+-{}|:<>?[]/;`, .= New Password Length : 4 ~ 30 0-9, A-Z, a-z ~!@#$%^*()_+-{}|:<>?[]/;`, .
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Table C Valid Characters for using WMI (continued) Block Field Valid Characters General Setup (CPE Mode) ESSID Length : 31 0-9, A-Z, a-z ~!@#$%^*()_+-{}|:<>?[]/;`, .
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Table C Valid Characters for using WMI (continued) Block Field Valid Characters BRIDGE Setup ESSID Length : 31 0-9, A-Z, a-z ~!@#$%^*()_+-{}|:<>?[]/;`, .= Peer's MAC Address 12 HEX chars VLAN ID 1 ~ 4094 ; 0 is disable Description Length : 32 0-9, A-Z, a-z Space ~!@#$%^*()_+-{}|:<>?[]/;`, .
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Appendix D. All Antenna type for Products A. Internal Patch 1 Antenna (Antenna Gain : 12.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE B. Internal Patch 2 Antenna (Antenna Gain : 11.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE C. Internal Patch 4 Antenna (Antenna Gain : 8.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE D. External Patch 4 Antenna with N-type Female reverse connector (Antenna Gain : 8.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.
User Manual WCB1000H5PX/WCB1010H5PX IEEE802.11bg High Power BS/Bridge/CPE Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
