Smart Construction Rover Dual GNSS Receiver ”SC Rover” Installation Manual
What is "SC Rover“ Setting Tool App "RTFSetting “ ? ■ "RTFSetting" Setting Tool App is a dedicated app for setting “SC Rover". ■ This is an Android device-only App. ■ This App may not be available on all Android devices. ■ “SC Rover” and Android device are set with Bluetooth communication.
“SC Rover” receiver port and Connection cable Power source: 9V ~ 36 Vdc or 4.
"SC Rover“ Connection Cable Reference Station System (Base Station) Mobile Station System SC Rover SC Rover Port1 Port2 Port1 Port1 Cable Port1 Cable Port2 Cable RTCM INPUT RS232C Power Line DC12V-24V Power can be supplied with an external power supplye. RTCM OUTPUT ※RTCM32MSM4 RS232C Modem Power Line DC12V-24V Power can be supplied with an external power supplye.
"SC Rover“ : Internal switch (Back side of receiver: Inside battery case ） When using an external power supply, but with a built-in battery and using the battery as a countermeasure against momentary interruption ON Temporarily use the battery for momentary interruption On Int Int : Setting Mode Ext : Normal mode OFF Using a battery as a power source Ext Off When using batteries, "Off" There is no problem if you use the switch with the wrong settings.
『RTF500』の設定準備（設定モードにする） "SC Rover“ Setup 6
"SC Rover“ : Setting preparation (Set to setting mode ） ■ Turn off the power of “SC Rover”. ■ Open the lid on the back of the main unit and switch the switch in the yellow frame to "Int". ■ Turn on the power of “SC Rover” main unit with a battery or an external power supply. *BATT Lump : Green when using batteries, red when using external power supply ■ After turning on the power, “SC Rover” starts in the setting mode. (It takes a few minutes to start up.
Turn on Bluetooth on Android device Turn on Android device and turn on Bluetooth. (Ex : Motog7) Motog7 Hold your finger on the top of the screen and slide it down. (Swipe down) Make sure Bluetooth is turned on. * The operation may differ depending on the Android device used.
“SC Rover” Setting App: Strat “RTFSetting” Tap "RTFSetting" icon. Tap "Search“ button.
Select Receiver to set The Receiver serial number referenced in "Search" is displayed. The serial number of "SC Rover“ is printed on the back cover of main unit. 接続完了 現在の設定内 容を表示しま す。 Tap the Receiver you want to set, then tap “Connect” button.
"SC Rover“ : Setup When “SC Rover" and Android device are connected via Bluetooth, the serial number of the connected receiver will be displayed. Once connected, the contents of the current receiver settings will be displayed.
Mobile Station System (Rover) : Setting Items Setting Value / Description Items Setting Value / Description Receiver Mode Please set to Rover. NMEA Out Rate PORT1 Baudrate Set PORT1 Cable (RS232C) communication speed. Please adapt the speed with the capture device or App for the NMEA output port. This is the output cycle of the NMEA message output to PORT1 or TCP port (50001). Please select from 1Hz, 5Hz, 10Hz. GGA Use Select ON to output NMEA-GGA and OFF to not output.
Reference Station System (Base Station) : Setting Items Setting Value / Description Items Setting Value / Description Receiver Mode Please set to Base Station. Base Lat PORT1 Baudrate （Modem） Set PORT1 Cable (RS232C) communication speed. This setting is used when using RTK with the radio. Please match with the RS232C communication speed of the radio. Enter the coordinates (latitude) of the location where the base station GNSS antenna is installed in decimal (degree format). Ex) 35.
"SC Rover“ : Correction wave of the Reference Station (Base Station) ■ When using an external radio with the “SC_Rover" Base station, the correction wave to be transmitted is fixed to "RTCM32MSM4". *SC_Rover can also be sent with "RTCM32MSM7", but the amount of data is about 1.7 times that of "RTCM32MSM4". In order to reduce the transmission data size, please transmit the data with "RTCM32MSM4".
Reference Station System (Base Station) : Setup Tap "Receiver Mode". Tap "Base Station".
Reference Station System (Base Station) : Setup When using an external radio, "PROT1 Baudrate (Modem)" Select the baud rate of the radio used in. Set “GPS” + “GLONASS” or “GPS” + “Beidou” to “ON”. *If other satellites are turned on, data transmission may not be possible depending on the specifications of the radio. * It depends on the specifications of the radio used. When using "SC Rover" as a base station, the correction wave to be transmitted is fixed to "RTCM32MSM4".
Reference Station System (Base Station) : Setup When the "Write successful" message is displayed, Tap "Exit“ This completes the Base Station settings. After the operation is completed, the screen returns to the home screen.
"SC Rover“ : Return from setting mode to measurement mode ■ Turn off the power of the "SC Rover" main unit. ■ Return the switch in the yellow frame on the back of the "SC Rover" from "Int" to "Ext". ■ Turn on the power of "SC Rover" and turn it "ON". This completes the Base Station setup procedure. Please connect to the radio and check the operation.
SC Rover Product Appearance
LANDLOG Ltd. 12F Sumitomofudosan Shibadaimon 2chome Building, 2-11-8 Shibadaimon, Minato-ku, Tokyo 105-0012 Japan Tel No +81-3-3578-7757 E-mail info@landlog.co.jp Declaration of Conformity Hereby, LandLog declares that Smart Construction Rover (model#: SC Rover) complies with part 15 of the FCC Rules.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
