Certification Exhibit FCC ID: R7PEG1R1S2 FCC Rule Part: 15.247 ACS Project Number: 12-0341 Manufacturer: Landis+Gyr Technology, Inc. Model: Gridstream RF Enhanced Integrated Focus AX 5015 B.U.
Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Publication: 98-1033 Rev AB LANDIS+GYR CONFIDENTIAL INFORMATION
Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr.
Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Overview The Gridstream RF Enhanced Integrated FOCUS AX module is an integrated solution with FOCUS AX advanced metering electronics the Gridstream AMR communication electronics combined together on a single PCB. It uses field-proven Digital Multiplication Measurement Technique to ensure a highly accurate load performance and dependability during the entire life of the product.
Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Landis+Gyr About the LAN ID The LAN ID is a unique identifier for each Gridstream RF endpoint. It is always displayed in hex. Landis+Gyr provides the LAN address. You cannot change the LAN ID of a radio. HAN Support The Gridstream RF Enhanced Integrated FOCUS AX communication module supports an integrated ZigBee system on the chip. This enables the endpoint to communicate via Smart Energy Profile 1.0 with other ZigBee enabled devices.
Landis+Gyr Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Availability of the following features depends on meter configuration.
Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Landis+Gyr The communication module stores a history of up to the last five power outage and restoration event pairs in the event log. The Host can request this data. Supporting Passwords The endpoint supports passwords provided by the utility. See two way Endpoint Testing Manager for loading password into the communication module.
Landis+Gyr Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Item General Description Pump Period Snap Read Not used. User ID 2 byte User ID used while running ANSI Logon Service Logon User 10 byte User Name that is used while running the ANSI Logon Service Security Password The full 20 bytes are required for the FOCUS AX. Sustained Outage Duration Defines the number of seconds after which an outage will be classified as sustained. If less than this amount, the outage is momentary.
Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Landis+Gyr interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: U • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.
Landis+Gyr Gridstream RF Enhanced Integrated FOCUS AX Quick Start Guide Category Specification Value or Range RF Frequency Range 2.405 GHz Min, 2.475 GHz Max RF Baud Rate 250 kbps Typ Output Power 17 dBm Min, 20 dBm Typ, 21 dBm Max, <2:1 VSWR load, approx. Receive Sensitivity -106 dBm Min, -104.5 dBm Typ, -102 dBm Max. At 1% PER Antenna type Inverted F, Printed Angenna Gain +5 dBi, Peak Gain FCC Title 47 CFR Part 15 Radiated and Conducted Emissions (incl.
Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Publication: 98-1245 Rev AA LANDIS+GYR CONFIDENTIAL INFORMATION
Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr.
Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Overview This publication outlines the procedure for remote passive antenna installation on Gridstream RF Electric Endpoints. Figure 1. Remote Passive Antenna This antenna couples radio frequency energy from a Landis+Gyr Gridstream RF Electric Endpoint's 902-928 MHz antenna into a coax cable connected to a remote antenna located at an optimal location for better connection to the Gridstream RF network. Coupling loss (including the 2.5 ft.
Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Landis+Gyr Required Materials The following materials are required to complete a remote antenna installation.
Landis+Gyr Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Performance Table 1. Performance Parameter Minimum Frequency 902 Typical Maximum Units 928 MHz 9 dB Coupling Loss 5 Polarization Linear VSWR 1.78:1 Impedance 50 ohm Input RL 11 dB Condition Final antenna assembly on FOCUS AX: modular Final antenna assembly on FOCUS AX: modular General Installation Guidelines Determine the optimum location for remote antenna installation.
Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Landis+Gyr Gridstream RF Enhanced FOCUS AX/AX-SD Mounting Procedure NOTE: The passive antenna should be mounted within 5 mm (0.25") of the indicated location to achieve specified performance. 1. Clean the meter cover where the flex antenna will be installed. Wipe the cover mounting area with an alcohol wipe and let the area dry for one minute before proceeding with the installation. 2.
Landis+Gyr Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Gridstream RF Enhanced S4e Mounting Procedure NOTE: The passive antenna should be mounted within 5 mm (0.25") of the indicated location to achieve specified performance. 1. Clean the meter cover where the flex antenna will be installed. Wipe the cover area with an alcohol wipe and let the area dry one minute before proceeding with the installation. 2.
Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Landis+Gyr Align the antenna center point on the meter housing at the 2:30 o’clock position, 1.5 cm clockwise past the nub on the outer meter cover Figure 5. Installation On Gridstream RF Enhanced S4e Meters Gridstream RF Integrated FOCUS AX/AX-SD Mounting Procedure NOTE: The passive antenna should be mounted within 5 mm (0.25") of the indicated location to achieve specified performance. 1.
Landis+Gyr Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide 6. Install the remote antenna at the location indicated by the link assessment performed. If a link assessment tool is not available, select a location that provides the best line of sight to the nearest collector. 7. Once installed to the antenna, wrap the connector using cold flow tape. Tape should be wrapped tightly and in a continuous manner. The tape should cover the cable one inch past the end of the connector. 8.
Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Landis+Gyr Antenna Brackets and Antenna Mounting Figure 8. Typical Remote Antenna Brackets 10 NOTE: To mount these brackets, use screw and bolt hardware that is approved by the local utility.
Landis+Gyr Gridstream RF Electric Endpoint Fix-up Antenna Installation Guide Grommet installed here, use RTV to Seal the meter can. Figure 9.