Table of Contents Snow Blowers SB1051, SB1064, SB1574, & SB2584 with S/N 881640- 33234 SB10 Series Shown with Optional Hydraulic Chute Rotor and Hydraulic Chute Tilt 370-027M Operator’s Manual ! Read the Operator’s Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Cover illustration may show optional equipment not supplied with standard unit.
Table of Contents Table of Contents Important Safety Information . . . . . . . . . . . . . 1 Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1 Look For The Safety Alert Symbol . . . . . . . . . . . . . 1 Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using This Manual . . . . . . . . . . . . . . . . . . . . . . .
▲ Table of Contents Important Safety Information Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Safety at All Times Thoroughly read and understand the instructions given in this manual before operation. Refer to the “Safety Label” section, read all instructions noted on them.
Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. 2 Use Safety Lights and Devices Transport Machinery Safely ▲ Slow moving tractors, self-propelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night. ▲ Flashing warning lights and turn signals are recommended whenever driving on public roads. ▲ Comply with state and local laws.
Table of Contents Important Safety Information These are common practices that may or may not be applicable to the products described in this manual. Prepare for Emergencies ▲ Be prepared if a fire starts. ▲ Keep a first aid kit and fire extinguisher handy. ▲ Keep emergency numbers for doctor, ambulance, hospital, and fire department near phone. Wear Protective Equipment Avoid High Pressure Fluids Hazard ▲ Wear protective clothing and equipment appropriate for the job.
Table of Contents Important Safety Information Safety Labels Your Snow Blower comes equipped with all safety labels in place. They were designed to help you safely operate your implement. Read and follow their directions. 1. Keep all safety labels clean and legible. 2. Refer to this section for proper label placement. Replace all damaged or missing labels. Order new labels from your nearest Land Pride dealer. To find your nearest dealer, visit our dealer locator at www.landpride.com. 3.
Table of Contents Important Safety Information 33248 818-858C Warning: To Prevent Serious Injury or Death 33248 818-634C Danger: Rotating Auger 33247 818-130C 33248 10/08/14 Caution: To avoid Injury or Machine Damage SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers 370-027M 5
Table of Contents Important Safety Information 848-840C Danger: Hands in Chute 2-Places: On both sides of chute Available after Oct. 1, 2011 33248 818-132C 33248 Danger: Thrown Object Hazard Hydraulic Cylinder Location Hydraulic Motor Location 848-747C Warning: High Pressure Fluid Hazard Used only with hydraulic motor and hydraulic cylinders.
Table of Contents Introduction Introduction Land Pride welcomes you to the growing family of new product owners. Pride dealer has trained personnel, repair parts, and equipment needed to service the implement. This Snow Blower has been designed with care and built by skilled workers using quality materials. Proper assembly, maintenance, and safe operating practices will help you get years of satisfactory use from this machine.
Table of Contents Section 1: Standard Assembly & Set-up Section 1: Standard Assembly & Set-up Tractor Requirements Chute Assembly Tractor horsepower and hitch category should be within the range noted below. Tractors outside the horsepower range must not be used. Refer to Figure 1-2: 1. Remove bearing strap (#2A) from Snow Blower housing. Keep cap screws (#3), bearing strap (#2A), chute bearings (#7), lock washers (#5), and hex nuts (#4) for reattachment of discharge chute (#1). 2.
Table of Contents Section 2: Optional Assembly & Set-up Section 2: Optional Assembly & Set-up 33237 SB1064, SB1574, & SB2584 Chute Rotation Powered By Manual Drive Figure 2-2 33238 SB1051 Chute Rotation Powered By Manual Drive Figure 2-1 For SB1064, SB1574, & SB2584 Models Chute Rotation, Manual The following instructions are for Snow Blower model numbers SB1064, SB1574, and SB2584 only. For SB1051 Model The following instructions are for Snow Blower model number SB1051 only. Refer to Figure 2-1: 1.
Table of Contents Section 2: Optional Assembly & Set-up 33235 Chute Rotation Powered By Electric Motor Figure 2-3 Chute Rotation, Electric Motor Refer to Figure 2-3: 8. NOTE: Existing bearing strap (#2) is replaced with new bearing strap (#8) and bolts (#9) are replaced with new bolts (#10). 1. Rotate discharge chute clockwise until chute is against chute stop and can not be rotated further. 2. Remove and discard bolts (#9) and bearing strap (#2). 3.
Table of Contents Section 2: Optional Assembly & Set-up Chute Rotation, Hydraulic Motor Refer to Figure 2-4: IMPORTANT: Adjustment screws on hydraulic motor are preset at the factory. Do not change factory settings. Changing factory settings can cause structural damage to the Snow Blower. 1. Rotate discharge chute clockwise until chute is against chute stop and can not be rotated further. 2. Remove bolts (#9), bearing strap (#2), chute bearings (#22), lock washers (#18), and nuts (#14).
Table of Contents Section 2: Optional Assembly & Set-up 33245 Chute Tilt Powered By Manual Drive Figure 2-5 33243 Chute Tilt Powered By Electric Actuator Figure 2-6 Chute Tilt, Manual Refer to Figure 2-5: 1. Attach lower single hole in adjustment tilt arm (#1) to lower chute lug with adjustment pin (#2). Secure adjust pin with hairpin cotter (#3). 2. Attach one of the multiple upper holes to the upper tilt chute lug with adjustment pin (#2). Secure adjustment pin with hairpin cotter (#3).
Table of Contents Section 2: Optional Assembly & Set-up Wear Bar, Lower Wear Bars, Outer Refer to Figure 2-8: 1. Attach wear bar (#1) to bottom of Snow Blower frame with 3/8"-16 x 1" GR5 plow bolt (#2) and hex flange lock nut (#3). 2. Tighten lock nut to the correct torque. Refer to Figure 2-10: 1. Attach adjustable wear bars (#1) to either the upper or to the lower holes in the side panels with 3/8"-16 x 1 1/4" GR5 carriage bolt (#2) and hex flange lock nut (#3). 2.
Table of Contents Section 3: Tractor Hook-up & Unhook Section 3: Tractor Hook-up & Unhook Snow Blower Hook-up Refer to Figure 3-2: Refer to Figure 3-1: ! ! DANGER Tractor hook-up to equipment is dangerous and can result in serious injury or death. Do not allow anyone to stand between tractor and Snow Blower while backing-up to implement. Do not operate hydraulic 3-point lift controls while someone is directly behind tractor or near the Snow Blower.
Table of Contents Section 3: Tractor Hook-up & Unhook Driveline Installation ! DANGER Do not engage tractor PTO while hooking-up and unhooking driveline or while someone is standing near the driveline. A person’s body and/or clothing can become entangled in the driveline resulting in serious injury or death.
Table of Contents Section 3: Tractor Hook-up & Unhook 24804 Outer Shielding has been removed for clarity. Driveline Maximum Extended Length Figure 3-4 23758 Driveline Shortening Figure 3-3 3. Hold inner and outer drivelines parallel to each other: a. Measure 1" (“B” dimension) back from outer driveline universal joint shield and make a mark at this location on the inner driveline shield. b.
Table of Contents Section 3: Tractor Hook-up & Unhook Hydraulic Hook-up ! DANGER Hydraulic fluid under high pressure can penetrate skin. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. Use a piece of cardboard or wood rather than hands when searching for hydraulic leaks. If hydraulic fluid is injected into the skin or eyes, it must be treated by a doctor familiar with this type of injury within a few hours or gangrene may result. DO NOT DELAY.
Table of Contents Section 3: Tractor Hook-up & Unhook Unhooking Snow Blower 1. See “Long Term Storage” on page 32 before parking Snow Blower for a long period. 2. Park on a level solid surface and lower Snow Blower to ground level or onto support blocks. 3. Engage tractor park brake, shut tractor engine off, and remove switch key. Stay on tractor until PTO has come to a complete stop. 4. Hydraulic Options: a.
Table of Contents Section 4: Adjustments Section 4: Adjustments Hitch Pin Locations 33289 Refer to The lower 3-point hitch pins and upper center bolt-on bushing can be arranged in the A-frame hitch three different ways depending on user preference. Standard 3-Point & Quick-Hitch Hook-up Bushing Is Located In Bottom Hitch Holes For Quick-Hitch. Use Upper Hitch Holes For Center 3-Point Link Refer to Figure 4-1: This is the most commonly used arrangement. 1.
Table of Contents Section 4: Adjustments Chute Rotation ! WARNING Never rotate chute to throw snow at the tractor. The Snow Blower is capable of picking up large solid objects and discharging them out the chute causing serious bodily injury or death. ! WARNING Never operate Snow Blower with chute throwing snow towards animals or people. The Snow Blower is capable of picking up large solid objects and discharging them out the chute at high speeds causing serious bodily injury or death.
Table of Contents Section 4: Adjustments 33287 33286 Outer Skid Shoes Inner Skid Shoe Assembly Figure 4-5 Inner Skid Shoes Refer to Figure 4-5: 1. Place support blocks under Snow Blower support rests (#7) to hold unit off the ground high enough to remove skid shoes (#1) from skid shoe mounts (#2). 2. Lower Snow Blower onto the support blocks, place tractor gearshift in park, shut tractor engine off and remove switch key. Make certain PTO is not running before dismounting from tractor. 3.
Table of Contents Section 4: Adjustments 33242 33288 Outer Wear Bar Assembly Figure 4-7 Roller Chain Take-up Adjustment Figure 4-8 Outer Wear Bars Roller Chain Take-up Refer to Figure 4-7: 1. Place support blocks under Snow Blower support rests to hold unit off the ground high enough to adjust wear bars (#1) up or down. 2. Lower Snow Blower onto the support blocks, place tractor gearshift in park, shut tractor engine off, and remove switch key.
Table of Contents Section 5: Operating Instructions Section 5: Operating Instructions Operating Checklist Hazard control and accident prevention are dependent upon the awareness, concern, prudence, and proper training involved in the operation, transport, storage, and maintenance of the Snow Blower. Therefore, it is absolutely essential that no one operates the Snow Blower without first having read, fully understood, and become totally familiar with the Operator’s Manual.
Table of Contents Section 5: Operating Instructions Safety Information ! DANGER Do not operate and/or travel across steep inclines where a tractor can slip or roll-over causing serious injury or death. Consult your tractor’s manual for acceptable inclines the tractor is capable of traveling across. Always operate Snow Blower with tractor flashing lights turned on. Be extremely careful blowing snow at night with rear bright lights on.
Table of Contents Section 5: Operating Instructions ! WARNING Do not operate Snow Blower with loose pins, bolts, and nuts. Loose hardware can result in a serious breakdown causing bodily injury or death. ! WARNING Never operate Snow Blower without good visibility and light. Use a tractor equipped with a cab to make seeing easier. ! WARNING Always dress to stay warm in cold weather. Use a tractor equipped with a cab to help stay warm and to protect against cold blowing snow.
Table of Contents Section 5: Operating Instructions IMPORTANT: Never operate Snow Blower with chute throwing snow towards property such as vehicles and buildings that can be scratched, dented, or broken by solid objects hitting them. IMPORTANT: Do not use Snow Blower as a Box Scraper or to blow other materials. Doing so can break the auger, impeller, gearbox, driveline, and cause structural damage to the unit. NOTE: Always check with local regulations to know where snow can be legally piled.
Table of Contents Section 5: Operating Instructions Turn your head to look where you are traveling while backing-up. Do not use rear view mirrors to view direction of travel while backing up. It is very important that you get a full field of view to prevent an accident. Beware of obstacles along side the tractor while making turns backing-up removing snow.
Table of Contents Section 6: Maintenance & Lubrication Section 6: Maintenance & Lubrication General Maintenance Information Auger & Impeller Inspection Proper servicing and adjustment is the key to the long life of any implement. With careful inspection and routine maintenance, you can avoid costly downtime and repair. Refer to Figure 6-1: 1. Check 3/8"-16 GR5 Impeller bolt (#3) for tightness, Make certain it is torqued tight. 2. Check impellers (#1) for wear, structural cracks, and breakage.
Table of Contents Section 6: Maintenance & Lubrication Shearbolt Protection The Snow Blower is protected from large objects entering the Snow Blower housing with a drive shaft shearbolt and a driveline shearbolt. They must be kept tight to keep them from wearing on the bolt holes and to prevent bolt wear. Two Holes For Storing Drive Shaft Shearbolts Drive Shaft Shearbolt Refer to Figure 6-2: There are two holes above the roller chain for storing extra drive shaft shearbolts with lock nuts.
Table of Contents Section 6: Maintenance & Lubrication Chute Bearings Refer to Figure 6-3 on page 29: Over time, the chute bearings (#1) can develop some wear making it hard to rotate chute (#3). If they do wear, loosen bolts (#2) and rotate chute bearings (#1) to a new wear surface. Retighten bolts (#2) to the correct torque before putting Snow Blower back into service. 8.
Table of Contents Section 6: Maintenance & Lubrication 33242 Outer Wear Bar Replacement Figure 6-8 33241 Outer Skid Shoe Replacement Figure 6-7 Outer Wear Bars (Optional) Refer to Figure 6-8: Outer Skid Shoes (Optional) Refer to Figure 6-7: Outer Wear Bar Part Numbers Outer Skid Shoe Part Numbers Part No. Part Description 370-013H 370-014H OUTER LEFT-HAND SKID SHOE OUTER RIGHT-HAND SKID SHOE Inspect outer skid shoes for wear and replace as needed. 1.
Table of Contents Section 6: Maintenance & Lubrication ! DANGER Always secure Snow Blower in the up position with solid supports before servicing underside of Snow Blower. Never work under equipment supported by hydraulics. Hydraulics can drop equipment if controls are actuated or if hydraulic lines burst. Either situation can drop the Snow Blower instantly even when power to hydraulics is shut off.
Table of Contents Section 6: Maintenance & Lubrication Lubrication Lubrication Legend Multi-purpose spray lube Multi-purpose grease lube Multi-purpose oil lube 50 Hrs Intervals in hours at which lubrication is required 10 Hours Shearbolt Sprocket Hub 1 - Zerk Type of Lubrication: Multi-purpose Grease Quantity = 2 Pumps 33249 10 Hours Auger Flange Bearings 2 - Zerks: Left Side Shown Type of Lubrication: Multi-purpose Grease Quantity = As needed 33250 As Required Drive Chain Type of Lubrication: Co
Table of Contents Section 6: Maintenance & Lubrication 33293 Do Not Overfill As Required Gearbox NOTE: Do not overfill! Snow Blower should be level when checking oil. Oil expands when hot, therefore, always check oil level when cold. SB1051 & SB1064 Gearbox Remove oil level plug shown with arrow. If oil is below bottom of plug hole, add recommended gear lube through oil level plug hole until oil flows out of the hole. Reinstall and tighten oil level plug.
Table of Contents Section 7: Specifications & Capacities Section 7: Specifications & Capacities SB10, SB15, & SB25 Series List Model No. Specifications & Capacities Model SB1051 Model SB1064 Model SB1574 Model SB2584 Working Width 51" 64" 74" 84" Overall Width 52 3/4" 65 3/4" 75 3/4" 85 3/4" Weight 390 lbs. 501 lbs. 545 lbs. 875 lbs. 18-32 HP 18-59 HP 30-59 HP 43-105 HP Cat. l Cat. l & ll Tractor Horsepower 3-Point Hitch Category Cat.
Table of Contents Section 7: Specifications & Capacities SB1051 = 52 3/4" SB1064 = 65 3/4" SB1574 = 75 3/4" SB2584 = 85 3/4" SB1051 = 63 1/4" SB1064 = 63 1/4" SB1574 = 69 3/4" SB2584 = 75" SB1051 = 53 1/4" SB1064 = 53 1/4" SB1574 = 56 1/4" SB2584 = 57 1/4" 36 SB1051, SB1064, SB1574, & SB2584 with S/N 881640- Snow Blowers 370-027M 33253 10/08/14
Table of Contents Section 8: Features & Benefits Section 8: Features & Benefits SB10, SB15, & SB25 Series Features Benefits Quality Comer Gearbox Provides long life, durability construction. Greaseable bearings Less drag and extends life of unit. Large main housing Ability to handle large drifts. Large impeller diameter The ability to move and throw material farther. Options Bolt-on hardened steel, cutting edge Improves service life of the Snow Blower.
Table of Contents Section 9: Torque Values Chart Section 9: Torque Values Chart Torque Values Chart for Common Bolt Sizes Bolt Head Identification Bolt Size (inches) 1 Grade 2 2 Grade 5 Bolt Head Identification Grade 8 Bolt Size (Metric) 3 5.8 8.8 10.9 Class 5.8 Class 8.8 Class 10.9 4 in-tpi N · m ft-lb N · m ft-lb N · m ft-lb mm x pitch N · m ft-lb N · m ft-lb N · m ft-lb 1/4" - 20 7.4 5.6 11 8 16 12 M 5 X 0.8 4 3 6 5 9 7 1/4" - 28 8.
Table of Contents Section 10: Warranty Section 10: Warranty Warranty Land Pride warrants to the original purchaser that this Land Pride product will be free from defects in material and workmanship beginning on the date of purchase by the end user according to the following schedule when used as intended and under normal service and conditions for personal use.
Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.