A Bluetooth Test Setup SaBLE-x-R2 Module Version 1.
Bluetooth Test Setup SaBLE-x-R2 Module REVISION HISTORY Version 1.0 Date 04/12/2017 Notes Initial Release Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 338-0016-R1.0 Approver RG 2 © Copyright 2017 Laird.
Bluetooth Test Setup SaBLE-x-R2 Module CONTENTS 1 Hardware Test Set-Up .......................................................................................................................... 4 1.1. 2 PCBA Preparation .................................................................................................................... 4 Software Test Setup ............................................................................................................................. 5 2.1.
Bluetooth Test Setup SaBLE-x-R2 Module 1 HARDWARE TEST SET-UP 1.1. PCBA Preparation #1 #2 #4 #5 #3 Figure 1: SaBLE-x-R2 Dev Board PCBA Note: #1 Keyed Power Connector: Red (+), Black (-); ▪ ▪ VMIN = 1.8V, VNOM = 3.3V, VMAX = 3.
Bluetooth Test Setup SaBLE-x-R2 Module 2 SOFTWARE TEST SETUP 2.1. Dev Board Setup with PC ▪ Apply external power via J6 on the PCBA (#1) ▪ Make sure all switches on S5 and S6 are set OFF on the PCBA (#5) ▪ Set switch 5 and 6 ON on S7 (#2) ▪ Set Switch to EXT (#4) Figure 2: COM Identifier ▪ Run Bluetooth RF Eval Tool Version 8.7.0.0 (Provided by LSR) Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 338-0016-R1.0 5 © Copyright 2017 Laird.
Bluetooth Test Setup SaBLE-x-R2 Module 2.2. Bluetooth RF Eval Tool Software ▪ Pick the appropriate COM port from Device Manager. Choose the appropriate Chipset which in this example is CC26XXR2F. ▪ Connect the device. The output will be displayed in the log window. Figure 3: Device Setup and Initial Output Reading Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 338-0016-R1.0 6 © Copyright 2017 Laird.
Bluetooth Test Setup SaBLE-x-R2 Module 2.2.1. BLE Transmit & Receive ▪ The channel index is determined by: Freq (MHz) = 2402 + 2k, for k = 0, 1, 2 … 39 (decimal) Ex: k = 0, Freq = 2402MHz; k = 19, Freq = 2440MHz; k = 39, Freq = 2480MHz ▪ Select the BLE 5.0 Option under the BLE Tab. Figure 4: BLE Transmit & Receive Setup Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 338-0016-R1.0 7 © Copyright 2017 Laird.
Bluetooth Test Setup SaBLE-x-R2 Module ▪ Select the necessary data rate options based on what BLE version is being tested for Transmit testing. Click on the Enhanced Tx Start button and the Test End to start and stop the transmitter. Figure 5: BLE Transmit Testing Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 338-0016-R1.0 8 © Copyright 2017 Laird.
Bluetooth Test Setup SaBLE-x-R2 Module ▪ Select the necessary data rate options based on what BLE version is being tested for Receive testing. Click on the Enhanced Rx Start button and the Test End to start and stop the transmitter. Figure 6: BLE Receive Testing Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 338-0016-R1.0 9 © Copyright 2017 Laird.
Bluetooth Test Setup SaBLE-x-R2 Module 3 CONTACTING LSR/LAIRD Headquarters ` LSR/Laird W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website https://www.lsr.com/ Technical Support http://info.lsr.com/contact Sales Contact sales@lsr.com © Copyright 2017 Laird. All Rights Reserved. Patent pending. Any information furnished by Laird and its agents is believed to be accurate and reliable. All specifications are subject to change without notice.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.