User's Manual

ManualsBrandsLaird Technologies ManualsElectronicsSaBLE-x

SaBLE-x Module

DATASHEET

The information in this document is subject to change without notice.

SaBLE-x

Bluetooth

Smart (BLE) Module

FEATURES

• Built in CC2640F128 Bluetooth

Smart (BLE 4.1) System-On-Chip

(SOC)

• 128 kB Flash / 20 kB SRAM

• RF Output Power: +5 dBm

• RF Receive Sensitivity: -96 dBm

• Size: 11.6mm x 17.9mm x 2.4mm

• Operating Voltage: 1.8V to 3.8V

• Operating Temperature: -40 to +85C

• 9.1mA Transmit Mode (+5 dBm)

• 6.1mA Receive Mode

• 1μA Standby (SRAM/CPU retention

and RTC running) with quick 100 μs

start up

• 200nA Shutdown

• 61μA/MHz Active CPU Current

• Drivers, Bluetooth Low Energy

Controller, and bootloader in ROM

• Flexible peripheral set

• On board 32 kHZ and 24 MHz

Crystals.

• Worldwide Acceptance: FCC (USA),

IC (Canada), ETSI (Europe), Giteki

(Japan), C-Tick (AU/NZ)

• REACH and RoHS compliant

APPLICATIONS

• Consumer electronics

• Mobile phone accessories

• Sports & Fitness equipment

• HID applications

• Home and Building Automation, Lighting

Control, Alarm and Security

• Electronic Shelf Labeling, Proximity

Summary of content (14 pages)

PAGE 1
SaBLE-x Module DATASHEET SaBLE-xTM Bluetooth® Smart (BLE) Module FEATURES • • • • • • • • • • • • • • • • • DESCRIPTION Built in CC2640F128 Bluetooth Smart (BLE 4.1) System-On-Chip (SOC) 128 kB Flash / 20 kB SRAM RF Output Power: +5 dBm RF Receive Sensitivity: -96 dBm Size: 11.6mm x 17.9mm x 2.4mm Operating Voltage: 1.8V to 3.8V Operating Temperature: -40 to +85C 9.1mA Transmit Mode (+5 dBm) 6.
PAGE 2
SaBLE-x Module DATASHEET TABLE OF CONTENTS FEATURES .......................................................................................................................... 1 APPLICATIONS ................................................................................................................... 1 DESCRIPTION ..................................................................................................................... 1 FOOTPRINT AND PIN DEFINITIONS..........................................
PAGE 3
SaBLE-x Module DATASHEET FOOTPRINT AND PIN DEFINITIONS 1 33 2 32 3 31 4 30 5 29 6 28 7 34 37 27 8 26 9 35 38 25 10 24 11 36 39 23 12 22 13 14 15 16 17 18 19 20 21 Figure 1 SaBLE-x Module Footprint (Viewed From Top) The information in this document is subject to change without notice.
PAGE 4
SaBLE-x Module DATASHEET PIN DESCRIPTIONS Module Pin Name I/O Type Description 1 RF OUT RF 2 GND GND GROUND 3 GND GND GROUND 4 NC - NO CONNECT (DO NOT CONNECT) 5 NC - NO CONNECT (DO NOT CONNECT) 6 /RESET DI 7 JTAG TCKC DI/DIO JTAG TCKC 8 JTAG TMSC DIO JTAG TMSC 9 NC - NO CONNECT (DO NOT CONNECT) 10 NC - NO CONNECT (DO NOT CONNECT) 11 VCC PI POWER SUPPLY TO MODULE 12 VCC PI POWER SUPPLY TO MODULE 13 DIO 5/JTAG TDO DIO GPIO, JTAG TDO, ULP SENSOR INTERFACE,
PAGE 5
SaBLE-x Module DATASHEET ELECTRICAL SPECIFICATIONS Absolute Maximum Ratings Symbol VCC Description Digital Input Supply Voltage Voltage on any digital pin Min Max Unit -0.3 4.1 V -0.3 VCC+0.3, max 4.1 V +5 dBm Input RF level Table 2 Absolute Maximum Ratings 1 Recommended Operating Conditions Test conditions: Ambient Temp = 25°C Symbol VCC Min Typ 1.8 3.3 Table 3 Recommended Operating Conditions Max Unit 3.
PAGE 6
SaBLE-x Module DATASHEET DC Characteristics Parameter Test Conditions Min Typ Max Unit Input low-to-high transition with hysteresis Transition from 01, TA= 25C, VCC=1.8V 1.07 V Input high-to-low transition with hysteresis Transition from 10, TA= 25C, VCC=1.8V .74 V Input hysteresis Difference between 01 and 10. .33 V Input low-to-high transition with hysteresis Transition from 01, TA= 25C, VCC=3.8V 1.
PAGE 7
SaBLE-x Module DATASHEET General Power Consumption TA = 25°C and VCC = 3 V Parameter Test Conditions Min Typ Max Unit Shutdown No clocks running, no data retention 200 nA Standby 1 With RTC, CPU, RAM and partial register retention. XOSC_LF 1.2 uA Standby 2 With Cache, RTC, CPU, RAM and partial register retention. XOSC_LF 2.7 uA Idle Supply Systems and RAM powered. 550 uA Active Core running CoreMark 1.45mA + 31uA/MHz Radio Receive Radio Transmit +5 dBm output power 6.1 mA 9.
PAGE 8
SaBLE-x Module DATASHEET AGENCY CERTIFICATIONS FCC ID: TFB-1002, 15.247 IC ID: 5969A-1002, RSS 210 CE: Compliant to standards EN 60950-1, EN 300 328, and EN 301 489 AGENCY STATEMENTS Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 9
SaBLE-x Module DATASHEET Industry Canada Statements This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.
PAGE 10
SaBLE-x Module DATASHEET OEM RESPONSIBILITIES TO COMPLY WITH FCC AND INDUSTRY CANADA REGULATIONS The SaBLE-xModule has been certified for integration into products only by OEM integrators under the following conditions: The antennas for this transmitter must not be co-located with any other transmitters except in accordance with FCC and Industry Canada multi-transmitter procedures. Co-location means having a separation distance of less than 20 cm between transmitting antennas.
PAGE 11
SaBLE-x Module DATASHEET OEM LABELING REQUIREMENTS FOR END-PRODUCT The SaBLE-x module is labeled with its own FCC ID and IC Certification Number. The FCC ID and IC certification numbers are not visible when the module is installed inside another device, as such the end device into which the module is installed must display a label referring to the enclosed module.
PAGE 12
SaBLE-x Module DATASHEET OEM END PRODUCT USER MANUAL STATEMENTS The OEM integrator should not provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product. Other user manual statements may apply. L'intégrateur OEM ne devraient pas fournir des informations à l'utilisateur final sur la façon d'installer ou de supprimer ce module RF ou modifier les paramètres liés RF dans le manuel utilisateur du produit final.
PAGE 13
SaBLE-x Module DATASHEET EUROPE CE Notice This device has been tested and certified for use in the European Union. See the Declaration of Conformity (DOC) for specifics. If this device is used in a product, the OEM has responsibility to verify compliance of the final product to the EU standards. A Declaration of Conformity must be issued and kept on file as described in the Radio and Telecommunications Terminal Equipment (R&TTE) Directive.
PAGE 14
SaBLE-x Module DATASHEET CONTACTING LSR Headquarters LSR W66 N220 Commerce Court Cedarburg, WI 53012-2636 USA Tel: 1(262) 375-4400 Fax: 1(262) 375-4248 Website www.lsr.com Technical Support forum.lsr.com Sales Contact sales@lsr.com The information in this document is provided in connection with LS Research (hereafter referred to as “LSR”) products.