USB Hub-Audio Series January 1999 A15-0157-110
USB Hub-Audio FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER: This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
USB Hub-Audio TABLE OF CONTENTS USB Hub-Audio..........................................................................................................3 Introduction.............................................................................................................3 USB Hub Device Driver Installation Under Windows 98 .....................................0 Verifying Correct USB Hub Device Driver Installation .................................................
USB Hub-Audio USB Hub-Audio Introduction Thank you for choosing our USB series products. We provide USB Hub, USB Audio and USB Hub-Audio which are combinations of Hub and audio. The following diagrams show you the back plates of the different devices.
USB Hub-Audio USB Hub Device Driver Installation Under Windows 98 1.) After starting up your Microsoft Windows 98 operating system, the “Add New Hardware Wizard” dialog box will be displayed on your screen. Click on “Next>”. Fig.1 2.) The “Add New Hardware Wizard” dialog box appears, asking you what Windows should do. Please choose ”Search for the best driver for your device. (Recommended)”, and click on “Next>”. Fig.2 3.) You will receive the following dialog box.
USB Hub-Audio Fig.3 4.) If Windows 98 could not find the correct driver program, the next dialog box will appear on your screen automatically. Fig. 4 5.) The “Insert Disk” dialog box may appear and ask you to insert the Windows 98 CDROM. Just insert it and continue by clicking on “OK”. Fig.
USB Hub-Audio 6.) The “Copying Files...” dialog box as shown below appears. Please specify the path of the device driver files as E:\Win98, assuming your CD-ROM drive is E. Click on “OK”. Fig.6 7.) The “Add New Hardware Wizard” dialog box appears again. Click on “Finish” and the installation of the software for your new hardware device has been finished. Fig.
USB Hub-Audio Verifying Correct USB Hub Device Driver Installation If you want to view the correct installation of the device driver for your new hardware device, please follow the steps as described below. 1.) Go to >”Start”/ >”Settings”/ >”Control Panel" and double-click on the “System” icon. 2.) The “System Properties” dialog box appears. Choose the “Device Manager” tap and double-click on “Universal serial bus controller”.
USB Hub-Audio USB Audio Device Driver Installation Under Windows 98 1.) After starting up your Microsoft Windows 98 operating system, the “New Hardware Found” dialog box will be displayed on your screen. Then a dialog box as displayed below appears. Please click on the “Next>” push button. Fig.9 2.) The “Add New Hardware Wizard” dialog box appears, asking you what Windows should do. Please choose ”Search for the best driver for your device. (Recommended)”, and click on the “Next>” button.
USB Hub-Audio Fig.10 5.) Just click on the “Next>” button and you will receive a dialog box as shown below. Please click on the “Finish” push button. Fig.11 6.) The next “Add New Hardware Wizard” dialog box will display the message “USB Human Interface Device”. Please continue by clicking on the “Next>” push button.
USB Hub-Audio Fig.12 7.) Please choose “Search for the best driver for your device (Recommended)”, and click on the “Next>” push button. Same as Figure 2 on page 3. 8.) Please make sure your Windows 98 CD-title has been inserted into your CD-ROM drive. Activate the box “CD-ROM drive” and click on the “Next>” push button. Same as Figure 3 on page 4. 9.) The following dialog box will display the message “USB Human Interface Device”. Accept the location of the driver by clicking on the “Next>“ push button.
USB Hub-Audio 10.) The dialog box displayed below will inform you that Windows has finished installing the software for your new hardware device. Click on the “Finish“ push button. Fig.14 11.) Now Windows will search for the new drivers for “USB Audio Device”. Click on the “Next>” push button. Fig.15 12.) Please choose “Search for the best driver for your device (Recommended)”, and click on the “Next>” push button. Same as Figure 2 on page 3. 13.
USB Hub-Audio 14.) The following dialog box will inform you that Windows is searching for the “USB Audio Device”. Please click on the “Next>” push button to accept the location of the device driver. Fig.16 15.) Windows 98 has finished installing the software for your new hardware device. Just click on the “Finish” push button. Fig.17 Congratulations! All installation procedures for the USB Audio device driver are complete, but you still have to ensure that the USB Audio works correctly.
USB Hub-Audio Verifying Correct USB Audio Device Driver Installation 1.) Click on the “Start” button from your Microsoft Windows 98 task bar. Select “Settings”, point at the “Control Panel” item and click on it. The “Control Panel” window will appear. Choose the “System” icon, double-click on it and a dialog box as displayed below will appear. Fig.18 2.) From the “System Properties” dialog box select the “Device Manager” tap.
USB Hub-Audio How to Enable USB Audio 1.) Please click on the “Start” button which is on the taskbar of your Microsoft Windows 98 operating system. Select “Settings” and point at the “Control Panel” item. From the “Control Panel” window double-click on the “Multimedia” icon. Windows 98 will display the “Multimedia Properties” dialog box. Please enable your “Audio” window same as below, then click on the “MIDI” tap. You will receive a dialog box as shown on the next page.
USB Hub-Audio 2.) Under “MIDI output” select “Single instrument” and highlight “Microsoft GS Wavetable SW Synth”. Just continue by clicking on the “CD Music” tap and you will receive the last dialog box as shown on the next page. 3.) The “CD Music” dialog box appears showing you the default CD-ROM drive for playing CD music. If you have more than one CD-ROM drive, make now your choice. You might also want to adjust the volume for your CD music. Do this by dragging the slide bare horizontally.
USB Hub-Audio Finally enable the digital CD audio for this CD-ROM device and click on the “OK” push button, so that all new selections can take effect. Now you are ready to play Audio CD, MIDI- or Wave files through the Multimedia Application Program of Microsoft Windows 98.
USB Hub-Audio Verifying Correct USB Hub-Audio Device Driver Installation 1.) Click on the “Start” button from your Microsoft Windows 98 task bar. Select “Settings”, point at the “Control Panel” item and click on it. The “Control Panel” window will appear. Choose the “System” icon, double-click on it and a dialog box as displayed will appear. 2.) From the “System Properties” dialog box select the “Device Manager” tap.
