User's Manual

ManualsBrandsLab Partners Associates ManualsCamera & PhotoCamera Remote

Table Of Contents

Quick Guide

FlexTT5

for Panasonic

340.00 – 354.00 MHz, US FCC/IC

433.42 – 434.42 MHz, CE

MAKE IT POSSIBLE

™

This PocketWizard radio runs on powerful software called ControlTL

It is pre-set with default settings allowing you to use it right away or it

can be congured to your specic needs using the PocketWizard Utility

which can be downloaded at:

www.PocketWizard.com/support/downloads.

• UPDATE FIRMWARE: Using the Utility, update all your PocketWizard

ControlTL radios to the latest rmware for best functionality.

• Please read Quick Guide thoroughly before operating.

• Visit wiki.PocketWizard.com for complete operating information.

Summary of content (11 pages)

PAGE 1
MAKE IT POSSIBLE™ Quick Guide FlexTT5 for Panasonic 340.00 – 354.00 MHz, US FCC/IC 433.42 – 434.42 MHz, CE This PocketWizard radio runs on powerful software called ControlTL®. It is pre-set with default settings allowing you to use it right away or it can be configured to your specific needs using the PocketWizard Utility which can be downloaded at: www.PocketWizard.com/support/downloads.
PAGE 2
FCC Statements FCC Part 15.19 Warning Statement THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE.
PAGE 3
FCC Part 15.105(b) Warning Statement (continued) If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
PAGE 4
Transceiver Mini-USB Connector (behind antenna) Lanyard Loop (Lanyard not included) Adjustable Antenna Batteries 2 AA [IEC:LR6] Zone Switch Configuration/Channel 1 Configuration/Channel 2 Power Off 1/4-20 Mount (on bottom) Hot Shoe TEST/LEARN Button Remote Flash Triggering Port (P2) Locking Ring Remote Camera Triggering Port (P1) Status LED • You need a FlexTT5 for each remote Speedlight. • Set all radios to the same channel.
PAGE 5
CLS / i-TTL Basic Wireless 1. Slide FlexTT5® Transceiver onto camera. 2. Slide Speedlight onto remote FlexTT5 Transceiver. Set the Zone Switch to your desired Zone. Repeat for each remote Speedlight. Note: You need a receiving FlexTT5 for each remote Speedlight 3. Make sure all your PocketWizard® radios are on the same channel and take pictures normally.
PAGE 6
Manual Flash Advanced Wireless CLS / i-TTL Flash on camera 1. Slide the FlexTT5® Transceiver onto the camera. 2. Slide the Speedlight onto the camera mounted FlexTT5 radio. Set the Zone Switch to your desired Zone. The On Camera Speedlight will use the power level for its corresponding zone. 3. Slide Speedlight onto remote FlexTT5 Transceiver. Note: You need a receiving FlexTT5 for each remote Speedlight 4. Set Zone Switch (A, B, C) on remote FlexTT5.
PAGE 7
Manual Flash Studio Flash, etc. Remote flash with or without CLS / i-TTL flash on camera 1. Slide FlexTT5® Transceiver onto camera. 2. Attach ControlTL or standard PocketWizard® radio to studio flash. 3. Make sure all your PocketWizard radios are on the same channel and take pictures normally. Note: Manual remote flashes are not calculated as part of the TTL exposure. For proper exposure, adjust your camera’s exposure settings, or adjust the power level directly on your remote flash.
PAGE 8
Other Functions Status LED Normal “waiting for trigger” operation = short blink every 2 seconds. Normal short blink color indicates battery level: Green Good battery Amber Warning – battery low Red Very low battery – change immediately Steady red LED in sync with TEST indicates normal transmission. (Hold for 10 seconds to teach – see Learn mode) Short red blink in sync with trigger indicates normal reception. Rapid red blinking when not triggering or half-pressing camera indicates error condition.
PAGE 9
Compatibility Panasonic cameras and Speedlights compatible with PocketWizard ControlTL radios: The FlexTT5 is compatible with the GH4 Camera and the DMW-FL580L and DMW-FL360L Speedlights. Visit wiki.PocketWizard.com for compatibility information. Some Panasonic equipment compatibility may be implemented via future firmware updates. PocketWizard Wiki – http://wiki.PocketWizard.
PAGE 10
Specifications Specifications Trigger Delay: 0 seconds – “faster than a wire” when using compatible Panasonic cameras. Note: Approximately 900 microseconds delay if using Basic Trigger Mode.
PAGE 11
PocketWizard.com Warranty This PocketWizard® product is covered under a two-year limited manufacturer’s warranty. For warranty details, and to register your product, please go to PocketWizard.com/support or contact your local PocketWizard Distributor. Distributor contact information can also be found at PocketWizard.com. To receive a copy of the two-year limited manufacturer’s warranty on this PocketWizard product, e-mail us at warranty@lpadesign.