User's Manual

ManualsBrandsLab Partners Associates ManualsElectronicsPW2-002

The

PocketWizard Plus

Users Manual

Put the magic of a Wizard into your photos

LPA Design

So. Burlington VT

Users Manual Rev 0.1

Current Rev's: Hardware Software

Transmitter 1.0 1.0

Receiver 1.0 1.0

Last Revision Date: 12/31/98

Mfg. by:

LPA Design

1350 Shelburne Road, Suite 265

So. Burlington, VT 05403

Phone: 1-802-864-8LPA

Factory Fax: 1-802-658-6125

Sales: 1-603-664-5010

Tech Support: 1-603-664-5010

Sales/Tech Fax: 1-603-664-9100

Sales E-Mail: sales @ lpadesign.com Web Page:

E-Mail: support @ lpadesign.com http://www.lpadesign.com

Summary of content (7 pages)

PAGE 1
The PocketWizard Plus Users Manual Put the magic of a Wizard into your photos LPA Design So. Burlington VT Users Manual Rev 0.1 Current Rev's: Transmitter Receiver Hardware 1.0 1.0 Software 1.0 1.0 Last Revision Date: 12/31/98 Mfg. by: LPA Design 1350 Shelburne Road, Suite 265 So. Burlington, VT 05403 Phone: 1-802-864-8LPA Factory Fax: 1-802-658-6125 Sales: Tech Support: Sales/Tech Fax: Sales E-Mail: E-Mail: 1-603-664-5010 1-603-664-5010 1-603-664-9100 sales @ lpadesign.com support @ lpadesign.
PAGE 2
Table Of Contents · · · · · · · · · · · Introduction / Features Getting Started / Using your PocketWizard Plus Installing Batteries Connecting the Transmitter to the Camera Connecting the Receiver to a Flash Pack Connecting the Transmitter to a Local Strobe Transmitter and Receiver Orientation Care and Feeding Troubleshooting Guide Warranty Obtaining Technical Support Introduction Congratulations on your purchase of the PocketWizard Plus radio slave.
PAGE 3
Getting Started Using your PocketWizard Plus 9. Install batteries or use an AC adapter in the transmitter and receiver. 10. Attach a sync cord (PC to miniphone is the most common) from your camera to the Sync In connector on the transmitter or use the hot shoe to mount the transmitter to your camera. Note that the Sync In and Sync Out jacks look the same,. 11. Attach a sync cord from the Sync Out connector on the receiver to your strobe pack 12.
PAGE 4
not exceed these limits. You may also purchase an LVT (Low Voltage Trigger) from LPA Design or your strobe manufacturer. TRANSMITTER and RECEIVER ORIENTATION Long range performance of your PocketWizard Plus radio slave system is dependent on orienting and positioning the units properly. In general, it is a good idea to have line of sight between the transmitter and the receivers. If this is not possible, try to keep the units away from large metal, concrete, or water-filled objects.
PAGE 5
Troubleshooting Guide There are very few things that can go wrong with the PocketWizard Plus. In most cases, the first indication of a problem is that "it just doesn't work". If you do have a problem, please follow the troubleshooting steps in order. Before you start troubleshooting: · Make sure that there are good batteries in both transmitter and receiver, or a working AC adapter plugged into the AC adapter jack.
PAGE 6
Warranty This warranty is given to you (the end user) by LPA Design, 1350 Shelburne Road, Suite 265, So. Burlington, Vermont, 05403, U.S.A. If you experience difficulty with your PocketWizard Plus (tm) product you may return the product to any factory authorized representative for repair. Please be certain that your product is properly packaged before shipment. If possible, use the original packaging. Seller is not responsible for damage during shipment.
PAGE 7
FCC Statements: WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.