Installation Instructions

ManualsBrandsLa Crosse ManualsClocks & RadiosTechnology® Curve LED Alarm

WWVB ATOMIC TIME SIGNAL

Page | 2 Page | 3 Page | 4

1.8” LED Atomic Clock

with Dual Alarms and USB Charging

Model: 617-249

DC:112818

POWER UP

1. Insert the provided stand into bottom of clock.

2. Insert the 5.0 volt power cord into an outlet, then into your

clock. Optional: Install 1-CR2032 battery (not included).

1. Hold then release the SET button to enter the Settings Menu.

2. Press and release the + or - buttons to adjust the values.

Hold to adjust quickly.

3. Press and release the SET button to conﬁrm and move to the next

item.

Settings Menu Order:

• Time Zone

• DST ON/OFF

• Hour

• Minutes

• Snooze Duration

SETTINGS

ADJUSTABLE BACKLIGHT HI-LO-OFF

FIND FAQS, AND MORE UNDER THE SUPPORT TAB HERE:

bit.ly/617-249

1 X CR2032

LITHIUM BATTERY

(INCLUDED)

5.0 V adapter

(included)

IMPORTANT: When powered on, the clock will immediately search for

the atomic time for 7 minutes. Hold the ATOMIC button for 3 seconds to

stop or start the search.

• During the atomic time search the buttons will not function.

• Backlight will dim.

• USB charge port will not work.

Signal Search Indicator:

• Receiving strong WWVB signal: LED ﬂashing

• Successful Reception: LED solid

• Failed Reception: LED disappears

The clock will automatically search for the WWVB signal every night

at 1:00 am, 2:00 am and 3:00 am. If there is still no WWVB reception,

the clock will search WWVB time signal again at 4:00 am and 5:00 am

alternatively.

• Press

to adjust the brightness (HI/ LO/OFF) of your clock.

• This can only be done when the unit is not sounding or searching for

the atomic time signal.

ALARM 1 & 2

In one setting for Alarm 1 & 2 you are able to::

• Set Alarm Time

• Activate/Deactivate Alarm

• Select Volume (HI/LO)

Note: The Blue LED Light next to the A1 or A2 indicates alarm is active.

Set Alarm 1 & 2:

1. Hold then release the ALM 1 • 2 button to enter the Alarm Settings.

2. Press and release the + or - buttons to adjust the values. Hold to

adjust quickly.

3. Press and release the ALM 1 • 2 button to conﬁrm and move to the

next item.

Alarm Settings Order:

• Alarm 1 Hour

• Alarm 1 Minutes

• Alarm 1 OFF/ON

• Alarm 1 HI/LO (volume)

• Alarm 2 Hour

• Alarm 2 Minutes

• Alarm 2 OFF/ON

• Alarm 2 HI/LO (volume)

Stop Alarm for 1 Day:

When alarm sounds. press the ALM 1 • 2 button once to stop the alarm

and reset to come on in 24 hours.

Snooze:

When alarm is sounding, press

once, the alarm will be silenced

and come on again after the snooze duration selected.

Tip: if your second alarm activates while the ﬁrst alarm is sounding or it is

in the snooze mode, the second alarm overrides the ﬁrst alarm (the ﬁrst

alarm is reset to come on the next day).

Summary of content (2 pages)

PAGE 1
.8” LED Atomic Clock POWE R UP W W VB ATO M I C T I M E SI GN AL 1. Insert the provided stand into bottom of clock. 2. Insert the 5.0 volt power cord into an outlet, then into your IMPORTANT: When powered on, the clock will immediately search for the atomic time for 7 minutes. Hold the ATOMIC button for 3 seconds to stop or start the search. • During the atomic time search the buttons will not function. • Backlight will dim. • USB charge port will not work. clock.
PAGE 2
U S B CH AR G I N G P ORT JOIN T HE CONVE RSAT ION CAR E + M AI N T E N AN C E WAR R AN T Y & F C C STAT E M E NT Note: This is a power-output charging port. It does not provide power to the alarm clock. Ask questions, watch detailed setup videos, and provide feedback on our social media outlets! WARNING: 1. This product may use a Button Cell Battery. 2. If swallowed, it could cause severe injury or death in just 2 hours. 3. Seek medical attention immediately.