User's Manual

ManualsBrandsL.R. Nelson ManualsElectronicsEZ Pro Command Irrigation Controller

8.5x11 folded once english, spanish,french, german,portugese,italian

EZ Command Remote Programmer Model 8600

INSTALLATION AND PROGRAMMING GUIDE P/N 90007552

The EZ Command Remote Programmer is capable of controlling all EZ Pro

controller functions including programming and manual zone operation

via a secure radio link. There can be a tremendous timesaving when

installing, servicing and operating a Nelson EZ Pro irrigation system

by using this technology.

Battery Installation

Remove the screw on the battery cover and remove the battery cover.

Install two new “C” (LR14 in Europe) size alkaline batteries. Replace

the battery cover and screw.

Low Battery Indicator

There is a Low Battery Warning symbol (Pudik show the symbol Low

battery warning from page 22 EZ Pro instructions) on the EZ Command

LCD. When this is displayed and flashing new batteries must be

installed in your EZ Command.

Note: When radio connected to the EZ Pro if the Low Battery Warning

symbol is displayed it means new batteries must be installed in the EZ

Pro

Turn the EZ Command Remote Programmer On and Off

Turn on the EZ Command Remote Programmer by pressing any key or moving

the dial to any position. After 1 minutes of non-use the unit will

automatically turn off. To turn the unit off when radio connected

press the Radio On/ Off key.

EZ Pro Radio Setup

A four digit Controller ID and a four digit Programmer Code must be

programmed into the EZ Pro controller prior to making a radio

connection. Once set the controller will store these in memory and a

radio connection can be made at any time.

0000

Controller

ID (0000 to 9999)

Programmer

Code (0000 to 9999)

AUTO

PROG

OFF

Summary of content (6 pages)

PAGE 1
8.5x11 folded once english, spanish,french, german,portugese,italian EZ Command Remote Programmer Model 8600 INSTALLATION AND PROGRAMMING GUIDE P/N 90007552 The EZ Command Remote Programmer is capable of controlling all EZ Pro controller functions including programming and manual zone operation via a secure radio link. There can be a tremendous timesaving when installing, servicing and operating a Nelson EZ Pro irrigation system by using this technology.
PAGE 2
Controller ID- Every controller must have a unique ID. This will prevent a conflict if more than one controller is within range of the radio signal. Write down the Controller ID for future reference. Warning: Do not select the same Controller ID for two controllers within 1 mile of each other. Improper radio operation may result. Programmer Access Code- Use the same Programmer Code for all of your EZ Pro controllers and EZ Command Remote Programmers .
PAGE 3
Range of Radio Signal Radio signal range is greatest when there is a clear line of sight between the EZ Pro and the EZ Command. The type and size of structure that the EZ Pro is located in as well as the local terrain may effect performance. Connected Operation After one minute of use without a dial turn or a button press the EZ Command will enter a “sleep” mode. This is to extend battery life. The unit will “wake” once a minute and update the LCD screen.
PAGE 4
Troubleshooting and Service for the EZ Command SYMPTOM Unable to radio connect Poor radio connection POSSIBLE CAUSE Controller ID and or Programmer Code do not match the EZ Pro controller Two EZ Pro controllers in range with the same Controller ID EZ Pro does not have a model 8602 Radio Module installed No AC power to the EZ Pro controller Out of range or signal blocked by obstruction Weak batteries Unit will not turn on Dead batteries Low Battery Warning (Pudik show the symbol Low battery warning from
PAGE 5
Two (2) Size C (LR14 in Europe) Alkaline batteries 3. Frequency 2.4 Ghz Spread Spectrum @ 10mw FCC RULES This equipment complies with PART 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. No user serviceable parts inside.
PAGE 6
granted, products will be repaired or replaced or a credit memorandum covering the net purchase price will be issued.