● Startup Screen and Initial Screen When the transmitter is switched on, the startup screen will display, followed by the initial screen. ※ Pressing the ENTER key during the startup screen will allow you to proceed to the initial screen. 【 Startup Screen 】 ① Version Information : Displays the version of the program that is installed in the Master Unit's CPU. This product's performance may be upgraded via paid or free upgrades. Check the Kyosho website for information regarding such upgrades. （ http://www.
● How to change the Modulation mode ● VR information setting Adjust the steering and throttle resistance information. ※ Please perform the VR information configuration to calibrate your system. ○ When using EX-6 for the first time. ○ When changing a steering unit for a different product or when putting it back together. ○ When changing a grip unit for a different product or when putting it back together. ○ When using and confusion has occurred in the positional information. EX-6 has two Modulation modes.
● Pairing Case of using the Xpansion unit ※ Refer to p.11 pairing Operation when not using the Xpansion unit. 2. Preparing the MINI-Z ① Bring distance of EX-6 and MINI-Z close to about 10cm. In order for the receiver to operate, it must store the transmitter's unique ID in its memory in a process called“pairing.”Even if a single transmitter is used to control multiple receivers, each receiver must go through the pairing process with the transmitter before being used for the first time.
■ TOP MENU FUNCTION STEERING This is an index which displays the 6 different function menus. This is an index which displays the 6 different function menus. Model Menu (MODEL) Steering Travel Operations such as selecting or copying a model. Modify the overall amount of steering movement. Timer Menu (TIMER) Steering Trim Operating timer-related functions. Modify the neutral position of the steering angle.
THROTTLE This is an index which displays the 10 different function menus. (Separated in 2 pages.) Throttle Travel MENU1 Modify the maximum throttle movement. Go back to throttle menu1. Throttle Trim Brake Override Modify the neutral position of the throttle. Modify the maximum amount of braking and steering travel assigned to a switch. Throttle Speed Throttle Reverse Modify the speed of the throttle's movement. Modify the throttle direction.
FUNCTION Model menu Save various settings as model memories Up to 20 model memories can be named and stored. ▶ MODEL NAME This function is used to name the model memory that is currently in use. Distinguish each model memory with different names, which may also be edited. The set model name will be displayed on the initial screen and model select screen.
MODEL ▶ MODEL COPY ▶ MODEL RESET Copies the current model memory to a different model memory. Return the current model memory to default factory setting values. 【Example】 When changing settings on the same car to match driving conditions, it is convenient to copy the original memory before modifying it. This function also allows you to try out new settings while keeping your original one. Select [RESET] (hold ENTER key) to reset. Select the model memory to copy to, then hold the ENTER key to copy.
TIMER Menu Operating Timer-related functions. 《Functions》 P ▶ TRGSTART Trigger Start Only the last recorded lap times may be checked and previously recorded results will not be saved. (Even if the transmitter is switched off, the last recorded times will remain in the memory.) Prepares the stopwatch for activation via the throttle movement. ▶ LAP HISTORY Displays the lap times recorded by the stopwatch. ▶ ALARM Alarm will sound after the set amount of time has elapsed. 100 lap times are memorized.
KEYSET Key setting Assign a key (ET1- ET5, BT1) to a function. ET1 ET2 ET4 If you select a key, the item is displayed to the right. It is assigned to a key by choosing an item. KEYSET キーセッテイ ET 1：S：TRIM ET 2：T：TRIM ET 3：T:BRAKE ET 4：S:TRAVEL ET 5：OFF BT 1：OFF 【Setting Range】 ET3 BT1 B T1 ET5 OFF S：TR IM S：TR AVEL S：FEEL T：TR IM T：H IPO INT ※ To use (ET4, ET5), No,10526 Expert grip (separately available option: Kondo Kagaku Co., Ltd.) is required.
3・4CH 3・4ch Menu Settings related to 3CH and 4CH operations. 【Setting Range】 START：POS 1, POS 2（Default：POS 1） Sets the starting position. KEY：OFF, ET1 〜 5（Default：OFF） Assigns a key to use for switching positions. POS 1：-100 〜 100（Default：0） Sets Position 1's output position. POS 2：-100 〜 100（Default：100） Sets Position 2's output position. 《Functions》 ▶ MODE OFF GYRO 2WAY TWIN 3WAY 4WS 5WAY AMP ANLOG T-MIX ▶ 3WAY MODE Modify the 3-position output settings. ※ Not used in MINI-Z.
3・4CH 3・4ch Menu LOW（Low Position）：-100 〜 0（Default：-100） ▶ 5WAY MODE Sets the lowest value for the operation range. CEN（Center Position）：LOW 〜 HIGH（Default：0） Modify the 5-position output settings. 【Example】 In MINI-Z MHS (such as MR-03VE PRO), it will control the gain of the steering gyro. As follows START: POS3, KEY: it will set in ET3. Sets the neutral position for the operation range. HIGH（High Position）：0 〜 100（Default：100） Sets the highest value for the operation range.
3・4CH 3・4ch Menu ▶ TWIN SERVO MODE ▶ 4WS This function modifies the setting for using 2 steering servo. Using left steering servo 1ch, and right steering servo 3ch or 4ch. ※ Not used in MINI-Z. 【Example】 Ackerman control is possible when using for drift cars using twin servos. 3CH MODE：４WS 3CH MODE：TWIN SERVO LEFT −ST （１CH） L・LEFT 70％ L・RIGHT 70％ L・SPEED 100％ L・TRIM 0 This function is related to an R/C car's 4-wheel steering feature.
3・4CH 3・4ch Menu ▶ AMP Mixing MODE On glow engine cars, an overly high setting value will increase load on the servo and lead to it being damaged. Check carefully while adjusting. ※ Not used in MINI-Z. Used when the front and rear wheels are controlled by separate ESCs and motors. If 3CH or 4CH is set to the front-wheel drive function, it will operate in conjunction with 2CH's throttle operations. On electric cars, a setting value that is too small may cause problems with the ESC settings.
3・4CH ▶ T-MIX 3・4ch Menu Throttle Mixing MODE ※ Not used in MINI-Z. 3CH MODE : T-MIX Mainly used for 1/5 scale R/C cars where the left/ right front wheels' braking operation is controlled by an independent servo. If 3CH is assigned to front right wheel brake and 4CH is assigned to front left wheel brake, they will operate in conjunction with 2CH (throttle) and 1CH (steering).
TRIM SET The convenient function that can set trim and travel while operating steering wheels. ▶ STEER AUTO BALANCE LEFT ① Move the cursor to "SET" and push the ENT key, "SET" will start blinking. ※ At this time, the steering travel(L) becomes 100 forcibly. ② Hold the steering wheel of the transmitter to the position that you want to make the Left end point. Set the steering travel(L) position when pushing the ENT key while holding the position.
SYSTEM MENU Menu related to various system settings. ▶ BATTERY Select the type of battery used. BATTERY バッテリー ▶ DISPLAY Setting about LCD display. DISPLAY ガメン LIGHTMODE バックライト LIGHTTIME ライトタイム P 4 KEY-ON P 5 【Setting Range】 CONTRAST : 1 ～ 5（Default : 4） Adjusts the contrast of the LCD. LCD contrast become low when the numerical value is reduced. P LIFe ﾘﾌｪ NI-MH ﾆｯｹﾙ LIPO ﾘﾎﾟ 【Setting Range】 DRY(Alkaline Batteries), Primary warning buzzer 4.
! WARNING ! Warning Display ▶ Battery Level Warning During driving, this warning will be displayed if the battery voltage is below the required level. You may still operate the model, but it is recommended to replace the battery immediately ※ In the case of DRY/Ni-MH setting, the LED (blue) of the main body of EX-6 flashes on and off, too. BATTERY WARNING LOW VOLTAGE EXIT >> KEY ON Furthermore, when the power supply voltage decreases, it is displayed and normal operation will not be able to continue.
SYSTEM MENU 3, Select [VR INFO] on the system screen and push the ENTER key. 4, Move the wheel slowly to the full left and right lock (numbers will change as the steering is moved) and release the wheel back to neutral. 5, Move the trigger slowly to the full throttle and full brake positions (numbers will change as the throttle is moved) and release the trigger back to neutral. 6, Select the "YES" on the right side of the display screen. ▶ CALCULATOR calculate the gear ratio.
SYSTEM MENU ▶ KEYSPEED Adjusts the delay between operations if the ET/BT key is pressed repeatedly. KEYSPEED KEYSPEED ｷｰｿｸﾄﾞ MENUSPEED ﾒﾆｭｰｿｸﾄﾞ ｷｰｿｸﾄﾞ 3 3 【Setting Range】 KEYSPEED : OFF ～ 5 （Default : 3） MENUSPEED : OFF ～ 5 （Default : 3） P OFF:Key Repeat Disabled. The larger value will shorten the delay time. The ET/BT keys speed is fixed and can not be independently changed. ▶ OPERATION ALARM When there is no input to the transmitter in over three minutes, an alarm will sound.
STEERING TRAVEL Modify the overall amount of steering movement. ▶ ST BALANCE L R Steering BalanceL R Adjust the left/right steering angles independently. This enables the turning radii to match up during cornering. 【Setting Range】 ST BALANCE L : 30 ～ 100 （Default : 70） ST BALANCE R : 30 ～ 100 （Default ： 70） ST TRAVEL トラベル P ST TRAVEL：100 The set percentage is a ratio of the value set by the Steering Travel.
TRIM MENU Adjusts the neutral/center position of the steering angle range. ▶ ST SUBTRIM Adjust the position of the overall steering angle range. ※ Also refer to Trim and Sub Trim Operation. (p.13) 【Setting Range】 ST SUBTRIM : L80 ～ 0 ～ R80 （Default : 0） ▶ ST TRIMRATE Adjusts the amount of movement associated with one click of the trim button.
ST SPEED Steering SPEED Modify the speed of the steering servo movement. ▶ ST TURN Steering Turn Speed This function limits the maximum speed of the steering servo by adjusting the steering turn direction [TURN] setting. 【Setting Range】 ST TURN SPEED : 1 ～ 100% （Default : 100%） 【Example】 When the car motion is too quick, you can reduce it. It will be easy to control the car.
