User's Manual

ManualsBrandsKyosho Corporation of America ManualsElectronicsTRANSMITTER



TRANSMITTER KT-19

产品介绍 Introduction

KT-19 遥控系统主要是用来遥控摩托车模型，通过对发射机进行操作，可以分别

实现相对应的马达驱动及舵机摆动遥控控制；发射机采用 6V/DC 供电，摩托车采用

3.7V 锂聚合物电池进行供电。

KT-19 radio system mainly uses for remote control the motorcycle model.

Through operating transmitter, it can succeed in moving the motor system and the

servo respectively. The transmitter will be supplied by 6V/DC, while the receiver will

be supplied by 3.7V li-poly battery.

产品套装：发射机+摩托车（接收机）+USB 线+充电器+使用说明书。

Product includes: transmitter + motor (receiver)+USB cable + charger + manual

KT-19 遥控系统使用方法及操作步骤

Instruction of KT-19

1. 将发射机与摩托车（接收机）靠近；

1. Keep the transmitter and model closer.

2. 将发射机手轮顺时针拧到底，然后按下电源开关“POWER”，此时发射机 LED 指示

灯会处于闪烁状态；

2. Turning the steering wheel to the end clockwise, and at the same time press the

POWER, then the LED will be flashing.

3. 打开接收机电源开关，接收机 LED 指示灯会长亮 2 秒时间，然后处于闪烁状态，

同时，无刷电机也会发出“滴、滴、滴”的响声；

3. Switch on the power of receiver, then the LED of receiver will be lighting for 2

seconds, after that it will be flashing, and at the same time the brushless motor will

be beeping.

Summary of content (6 pages)

PAGE 1
TRANSMITTER KT-19 产品介绍 Introduction KT-19 遥控系统主要是用来遥控摩托车模型，通过对发射机进行操作，可以分别实现相对应的马达驱动及舵机摆动遥控控制；发射机采用 6V/DC 供电，摩托车采用 3.7V 锂聚合物电池进行供电。 KT-19 radio system mainly uses for remote control the motorcycle model. Through operating transmitter, it can succeed in moving the motor system and the servo respectively. The transmitter will be supplied by 6V/DC, while the receiver will be supplied by 3.7V li-poly battery.
PAGE 2
4. 重启发射机电源开关，此时发射机和接收机的 LED 灯都会处于常亮状态，摩托车无刷电机连续发出 15 声“滴、滴、滴”的响声，然后陀螺马达开始转动; 4. Switch on the transmitter once more, both of the LED of transmitter and receiver will keep lighting. The brushless motor will keep beeping 15 times after that the motor of gyro starts to move. 5. 约 5 秒后运转速度达到正常，就可以通过控制发射机的手轮、扣机和陀螺仪的微调，达到遥控摩托车的方向及车速的目的。 6. The motor will be at the correct speed after 5 seconds. Through operating the trim of steering wheel, trigger and gyro to adjust the steering and speed of motor.
PAGE 3
The parameter of motor 摩托车机身长、宽、高：116 x 70 x 70mm； The size of motor is 116*70*70mm 发射机外观功能指示图： The name of different part on the transmitter 9 1 12 11 10 2 7 3 8 4 5 6 1. 天线 2.LED 灯透明盖 3.USB 线接口 4.电池盒开关 5.手柄皮套 6.电池盒 7.手轮 8.扣机 9.方向中位微调 10.陀螺 LO SPEED 微调 1. Antenna 5. 2. rubber grip 11. 陀螺 HI SPEED 微调 Cover of LED 6. Battery box 3. Port of USB 12.POWER ON/OFF 4. Switch of battery box 7. Steering wheel 8.
PAGE 4
9. Trim of steering 11. 10. Trim of gyro (low speed ) Trim of gyro (high speed) 12. Power on/off 供电电池说明 The instruction of battery 发射机采用 4 节干电池供电，电池型号为 AAA/1.5V；接收机采用 3.7VLi 电池供电。 The transmitter will be supplied by 4 cells dry battery; the model of battery is AAA/1.5V. A cell, while the receiver will be supplied by 3.7V Li-poly battery. 发射机输入电压 4.8V-6VDC。打开发射机电源按钮“POWER”，电源指示灯（绿色）常亮；当电池电压低于 4.2V 时，LED 指示灯会处于闪烁状态，此时需及时更换新电池。 The input voltage for transmitter is 4.8-6VDC.
PAGE 5
When the LED is green, it means the battery is full or the battery fail to connect. 注意事项 Notes 此款遥控模型运用了多款高科技技术，设计制造有一定的复杂性，使用之前请详细阅读《KT-19 使用说明书》，掌握相应的操作技术及安全规则。 The radio uses several high technologies, and the design and production are complex, so please read the manual carefully and master the operation and safety rules before using. 1. 在马达停止运转之前，小心用手去触摸； 1. Don’t touch the motor before it stops to move. 2. 每次使用模型之前，需检查摩托车模型及遥控系统功能是否正常； 2.
PAGE 6
5. The transmitter and receiver are component by many precise electronic parts. Please keep them from the humidity to avoid causing any kind of circuit problems. 警告 Warming 保养方法：需防震、防火、防潮。 Method of maintenance: Keep them from shaking, fire and humidity. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.