取扱説明書 INSTRUCTION MANUAL オートレンジ デジタル マルチメータ・AUTO RANGE DIGITAL MULTIMETER MODEL 1009 KYORITSU ELECTRICAL INSTRUMENTS WORKS,LTD.
1. Safety Warnings This instrument has been designed, manufactured and tested according to the following standards. IEC 61010-1 Over voltage CATⅢ 300V Pollution degree 2 IEC61010-031 IEC 61326 This instruction manual contains warnings and safety rules which must be observed by the user to ensure safe operation of the instrument and retain it in safe condition. Therefore, read through these operating instructions before using the instrument.
CAUTION ● Always make sure to check Function switch is setting to the appropriate range before starting measurement. ● Do not expose the instrument to the direct sun, high temperature and humidity or dewfall. ● When the instrument will note be in use for a long period, place it in storage after removing the batteries. ● Use a cloth dipped in water or neutral detergent for cleaning the instrument. Do not use abrasives or solvents. ● Allowable measurement time at 10A range of current function is 15seconds.
2. Features This instrument, 1009, is a Digital Multimeter which designed for making measurement of the low-voltage equipment. (1) Designed to international safety standards. (6) Auto-ranging function IEC 61010-1 overvoltage CAT.
DCA ACA 0∼10A (2 Autoranging) 4A 10A 400uA 4000uA 40mA 400mA 4A 10A Resistance Ω Frequency 0∼40MΩ (6 Autoranging) Test current approx. 0.4mA 0∼400Ω 40nF 400nF 4uF 40uF 100uF 5.12Hz 51.2Hz 512Hz 5.12kHz 51.2kHz 512kHz 5.12MHz 10MHz DUTY ● Standards ● Mode of operation ● Indication ● Over range display ● Auto-ranging ● Sampling rate 0∼4000uA (2 Autoranging) 0∼400mA (2 Autoranging) 0∼10A (2 Autoranging) ±2.6%rdg±4dgt (50 / 60Hz) ±3.0%rdg±4dgt (∼400Hz) ±2.0%rdg±4dgt (50 / 60Hz) ±3.
● Operating Environmental conditions ● Temperature & Humidity range (guaranteed accuracy) ● Operating Temperature & Humidity range ● Storage Temperature & Humidity range ● Insulation Resistance ● Withstand Voltage ● Overload Protection ● Dimensions / Weight ● Power source ● Accessories ● Fuse −indoor use −altitude up to 2000m 23℃±5℃ Relative humidity: less than 75% 0℃∼+40℃ Relative humidity: less than 80% -20℃∼+60℃ Relative humidity: less than 70% It should be more than 10MΩ/DC1000V between electrical
5. Preparation 5-1 Checking Battery Voltage Set the Function Selector Switch to other positions except the OFF position. Battery Voltage is enough if indication is clear and −+ symbol is not indicated in this bout. If −+ symbol is indicated or no indication on the display, follow to the Battery Replacement procedures shown in item8 in this document and replace with new batteries. 6.
(2) Set the Function Selector Switch to the appropriate "uA" or "mA" position. In case that the measurement current is 3999uA or less, set the Function Selector Switch to "uA" position, and it is 399.9mA or less, set the Function Selector Switch to "mA" position.(Then, "AUTO", and "uA"or "mA" symbols are indicated on the display.) (3) Power off the circuit under test.
(4) Power off the circuit under test. (5) Connect the test leads to the circuit under test so the instrument is in the series. (6) Power on the circuit under test. (7) Measured value is indicated on the display. 6-3 Resistance Measurement (Ω/ Diode check/ Continuity Check) DANGER ● To avoid the danger of getting electrical shock, never make measurement of the circuit in which electric potential exists. ● Do not make measurement when opening the battery cover and the instrument case.
6-4 Capacitance Measurement DANGER ● To avoid the danger of getting electrical shock, never make measurement of the circuit in which electric potential exists. ● Do not make measurement when opening the battery cover and the instrument case. ● Make sure to discharge the capacitor before making measurement. (1) Insert the black test lead plug into the COM terminal and the red test lead plug into the VΩHz terminal. (2) Set the Function Selector Switch to " " position.
● Current function (uA, mA, A) When setting the instrument to any function of the "uA", "mA", and "A", DC Current Measuring mode has been selected in the initial condition. By pressing "SELECT" Key, measuring mode changes. "DC" → "AC" 7-2 RESET Key By pressing "RESET" Key, all functions can be reset to their initial conditions. Range setting, Mode setting and Data hold are all released and every function is back to its initial condition.
8. Auto Power Off Auto power off function operates when about 30minutes passed after power on this instrument. When Auto power off function operates and the instrument powered off, the power-off statue returns to normal by pressing any key. And it is possible to release the Auto power off function. Turn the function switch from OFF position to the function you want with pressing SELECT key, and power on the instrument. 9.
保 DISTRIBUTOR MODEL 保証期間 1009 ご購入日 ( 証 書 製造番号 年 月 日)より1カ年間 共立製品をお買い上げいただきありがとうございます。 保証期間内に通常のお取扱いで万一故障が生じた場合は、 左記の保証規定により無償で修理いたします。 本書を添付の上ご依頼ください。 お名前 ご住所 〒 お電話番号 Kyoritsu reserves the rights to change specifications or Designs described in this manual without notice and without obligations.