WLAN (11b/g/n 1x1) USB module KYOCERA Model : DHUA-K77-8 User Manual Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Pentium is trademark of Intel. All copyright reserved.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Integration instructions for host product manufacturers Applicable FCC rules to module FCC Part 15.247 Summarize the specific operational use conditions The module is must be installed in mobile device.
Antennas Label and Compliance Information Product manufacturers need to provide a physical or e-label stating “Contains FCC ID: E52-K778” with finished product Information on Test Modes and Additional Testing Requirements Test tool: QRCT, Version: 3.0.187.0 shall be used to set the module to transmit continuously.
Industry Canada statement: This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.
Europe – EU Declaration of Conformity This device complies with the essential requirements of the Radio Equipment directive: 2014 / 53 / EU. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment directive: 2014 / 53 / EU: EN 300 328 V2.2.2 EN 301 489-1 V2.1.1 EN 301 489-17 V3.1.1 EN 62311:2008 EN 50665:2017 EN 50385:2017 IEC 622368-1:2014; and/or EN 62368-1:2014+A11:2017 19.98dBm, 2400-2483.5MHz SW version: v1.
端末機器の技術基準設計認証の認定番号 本製品は以下に認証を受けたものです。 認証機器名:DHUA-K77-8 認定番号: R 201-XXXXXX Taiwan 警語 第十二條→經型式認證合格之低功率射頻電機,非經許可,公司,商號或使用者均不得擅 自變更頻率、加大功率或變更原設計之特性及功能。 第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象 時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信法規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工 業、科學及醫療用電波輻射性電機設備之干擾。 Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於平 台上標示「本產品內含射頻模組: CCXXxxYYyyyZzW」字樣.
Table of Contents 1. INTRODUCTION 2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 3. CONNECTING TO AN EXISTING NETWORK 4. MODIFYING A WIRELESS NETWORK 4.1 MODIFYING GENERAL SETTINGS ................................................................................................ 4.2 MODIFYING SECURITY SETTINGS ................................................................................................ 5.
1. INTRODUCTION DHUA-K77-8 is a 802.11 b/g/n Wireless module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. System Requirements - 128 MB of RAM or later (recommended) - 300 MHz processor or higher 2. Driver/Utility Installation The driver should have been installed before the Printer is shipped from the manufacturer.
4. Modifying a Wireless Network 4.1 Modifying General Settings 1. Use the remote control that came with your Printer to access the network configuration settings page. 2. From the profile list, select one profile and choose the modify function. 3. Modify the settings below for your network. Profile Name Identifies the configuration wireless network profile. This name must be unique. Profile names are not case sensitive. Client Name Use this profile for Identifies the client machine.
4.2 Modifying Security Settings 1. Use the remote control that came with your Printer to access the network configuration settings page. 2. Select a security option of this wireless network. This product provides security options below. Contact your wireless network administrator for choosing a correct option. WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None WPA/WPA2 WPA/WPA2 Passphrase 802.1x Enables the use of Wi-Fi Protected Access (WPA).
None No security (not recommended). Allow Association to Mixed Cells Check this check box if the access point with which the client adapter is to associate has WEP set to Optional and WEP is enabled on the client adapter. Otherwise, the client is unable to establish a connection with the access point. Check this check box and enter the number of seconds (up to 300) after which the authentication process times out when trying to find the domain controller.
5. Product Specifications Product Name:WLAN (11b/g/n 1x1) USB module Brand Name:KYOCERA Model Name:DHUA-K77-8 Item Frequency Content 2400~2483.5 MHz range Channel spacing 5MHz Modulation technology DSSS : CCK,DQPSK,DBPSK OFDM :BPSK,QPSK,16QAM,64QAM 802.11b: 11/5.5/2/1Mbps 802.11g: 54/48/36/24/18/12/9/6Mbps Data Rate 802.11n: MCS0~MCS7(65Mbps) Host interface USB 2.0 Operation voltage 5V Antenna Type PCB printed ANT Antenna gain Antenna peak gain 2.