PA2X6BT & PA3X6BT Owner’s Manual Congratulations on the purchase of your Kustom Tower Speaker! These models draw on decades of electronic design and manufacturing experience at Kustom. This model was built from the ground up to offer useful features, high signal-to-noise ratio, and reliable performance. Inside this manual, you’ll find valuable information about your product’s controls and specifications. Being familiar with its features will help you effectively use your Kustom product.
IMPORTANT SAFETY INSTRUCTIONS Danger Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. 1. 2. 3. The U.S. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: 4. DURATION PER DAY (HOURS) 8 6 SOUND LEVEL (dB) 90 93 6. 7.
IMPORTANT SAFETY INSTRUCTIONS FRENCH 1. Danger L‘exposition a des niveaux eleves de bruit peut provoquer une perte permanente de l’audition, Chaque organisme humain reagit differemment quant a la perte de l’audition, mais quasiment tout le monde subit une diminution de I’acuite auditive lors d’une exposition suffisamment longue au bruit intense.
4 4 3 3 5 5 2 6 7 11 1 8 9 14 BLUETOOTH PAIRING INSTRUCTIONS: To connect your Bluetooth device to the .XVWRP %OXHWRRWK UHFHLYHU IRU WKH ¿UVW time, navigate to the Bluetooth settings menu on you Bluetooth enabled device. Ensure that Bluetooth is enabled and your Kustom product is powered on. Perform a scan for available devices. Select and pair to the Kustom product in the list of available devices. Enter 0000 for the passcode if prompted. Once paired, a connection can be established.
CONTROLS & FUNCTIONS OVERVIEW 1. MIC INPUTS: Connect dynamic and condenser microphones here. These inputs are designed for low-impedance mics and equipment that has a mic-level, balanced output. 15-volt phantom power is supplied to all MIC Inputs. 2. LINE INPUTS: These ¼-inch inputs may be used to connect high-impedance microphones, keyboards, drum modules and other audio devices. 3. LOW: Adjusts bass frequencies (@100Hz) per channel. Turn clockwise to boost, counter-clockwise to cut. 4.
PA2X6BT SpeciĮcaƟŽns Peak Output Power 200W 4 ohm load CH1 and CH2 Mic XLR Balanced, Line Level 1/4" Un-balanced Accepted Inputs Ch3 1/8" Line Level or Bluetooth Device -56dB Residual Noise, all level controls 0% (mimimum) Hum & Noise -48dB Nominal System Noise, all level controls at 50% System Gain/Speaker Output +70dB Mic to Speaker Output (CH 1 & CH2) (Measurement made at 1kHz) +56dB Line to Speaker Output (CH1 & CH2) +42dB Aux In to Speaker Output Channel EQ (high, low) 4kHz and above, 800Hz and below
3 2 1 AUX MIC LINE MIC LINE Bluetooth Receiver Phantom Power 15V Phantom Power 15V GAIN GAIN low low low high high high Aux Input Disables Bluetooth volume volume volume CHANNELS OUT IN SYNC MASTER LINKING BUS MASTER SUB LP Filter Conditioning Hi Pass Filter (HPF) HORN POWER AMP + _ + _ + _ SUBWOOFER OUT Inserting 1/4" mono (tip/sleeve) SHIELDED instrument cable into subwoofer out jack activates HPF.
PA3X6BT 17 18 4 4 3 3 5 5 2 6 7 11 1 10 8 9 SYNC 14 12 12 Model: PA3X6BT 15 16 13 BLUETOOTH PAIRING INSTRUCTIONS: To connect your Bluetooth device to the .XVWRP %OXHWRRWK UHFHLYHU IRU WKH ¿UVW time, navigate to the Bluetooth settings menu on you Bluetooth enabled device. Ensure that Bluetooth is enabled and your Kustom product is powered on. Perform a scan for available devices. Select and pair to the Kustom product in the list of available devices.
CONTROLS & FUNCTIONS OVERVIEW 1. MIC INPUTS: Connect dynamic and condenser microphones here. These inputs are designed for low-impedance mics and equipment that has a mic-level, balanced output. 15-volt phantom power is supplied to all MIC Inputs. 2. LINE INPUTS: These ¼-inch inputs may be used to connect high-impedance microphones, keyboards, drum modules, and other audio devices. 3. LOW: Adjusts bass frequencies (@100Hz) per channel. Turn clockwise to boost, counter-clockwise to cut. 4.
PA3X6BT SpeciĮcaƟŽns Peak Output Power 300W 4 ohm load CH1 and CH2 Mic XLR Balanced, Line Level 1/4" Un-balanced Accepted Inputs Ch3 1/8" Line Level or Bluetooth Device -46dB Residual Noise, all level controls 0% (mimimum) Hum & Noise -37dB Nominal System Noise, all level controls at 50% System Gain/Speaker Output +49dB Mic to Speaker Output (CH 1 & CH2) (Measurement made at 1kHz) +35dB Line to Speaker Output (CH1 & CH2) +25dB Aux In to Speaker Output Channel EQ (high, low) 4kHz and above, 800Hz and below
3 2 1 AUX MIC LINE MIC LINE Bluetooth Receiver Phantom Power 15V Phantom Power 15V GAIN Effect Select GAIN high Aux Input Disables Bluetooth high volume Effect Level 2 volume low low volume Effect Level 1 high Digital Effects low CHANNELS BALANCED MONITOR OUT OUT IN SYNC LINKING BUS MONITOR LEVEL MASTER MASTER SUB LP Filter Conditioning Hi Pass Filter (HPF) POWER AMP1 3kHz 3kHz 3kHz Crossover + _ + _ + _ + _ 8 ohm 8 ohm 8 ohm 8 ohm SUBWOOFER OUT Inserting 1/
EC Declaration of Conformity We: Kustom Musical Amplification INC. 3015 Kustom Drive Hebron, Ky 41048 Tel: 1-859-817-7100 Fax: 1-859-817-7150 Declare that the product Product name: Kustom Product model number: PA2X6BT/ PA3X6BT to which this declaration relates is in conformity with the following standards; EN55032: 2012 Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and associated equipment.
3$ ; %7 3$ ; %7 OWNER’S MANUAL www.kustom.