PW100BT Owner’s Manual Congratulations on the purchase of your PW100BT. Your PW100BT Model draws on decades of amp design and manufacturing experience at Powerwerks. This model was built from the ground up to offer world-class tone, useful features and reliable performance. Inside this manual, you’ll find valuable information about your product’s controls and specifications. Being familiar with its features will help you effectively use your system.
IMPORTANT SAFETY INSTRUCTIONS Danger Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S.
IMPORTANT SAFETY INSTRUCTIONS FRENCH 1. Danger L‘exposition a des niveaux eleves de bruit peut provoquer une perte permanente de l’audition, Chaque organisme humain reagit differemment quant a la perte de l’audition, mais quasiment tout le monde subit une diminution de I’acuite auditive lors d’une exposition suffisamment longue au bruit intense.
6 5 5 4 4 2 3 7 1 9 8 10 11 12 13 14 BLUETOOTH PAIRING INSTRUCTIONS: To connect your Bluetooth device to the Powerwerks Bluetooth receiver for the first time, navigate to the Bluetooth settings menu on you Bluetooth enabled device. Ensure that Bluetooth is enabled and your Powerwerks product is powered on. Perform a scan for available devices. Select and pair to the Powerwerks product in the list of available devices. Enter 0000 for the passcode if prompted.
CONTROLS & FUNCTIONS OVERVIEW INPUT SECTION: This is where you may plug in microphones, instruments, keyboards, drum machines and other audio devices, adjust the volume, bass and treble. 1. MIC Inputs: These XLR inputs are designed for low-impedance microphones or equipment that has a mic-level, balanced output (often called a Direct Out). Note: These inputs receive 15-volt phantom power. This is used to provide power to condenser microphones.
PW100BT Specifications Output Power 1% Accepted Inputs Frequency Response Hum & Noise System Gain (Measurements made at 1kHz) Channel EQ (high, low) POWERLINK (IN and OUT) Subwoofer Out Phantom Power Power Requirements Speakers Horn Power Capacity Frequency Response Nominal Impedance Bluetooth Module Features Dimensions & Weight 100W CH 1 and 2 CH3 4 Ohm load Mic XLR Balanced, Line level 1/4" Un-balanced 1/8” Line Level or Bluetooth Device Actual response is tailored to speaker cabinet for 20HZ-20kHz accu
3 2 1 AUX MIC LINE MIC LINE Bluetooth Receiver Phantom Power 15V Phantom Power 15V GAIN GAIN low low low high high high Aux Input Disables Bluetooth volume volume volume CHANNELS OUT IN POWERLINK MASTER LINKING BUS MASTER SUB LP Filter Conditioning Hi Pass Filter (HPF) HORN POWER AMP + _ + _ _ + _ + + _ LO SUBWOOFER OUT Inserting 1/4" mono (tip/sleeve) SHIELDED instrument cable into subwoofer out jack activates HPF.
This warranty is for Powerwerks products only. Any service claims resulting from other brands used in conjunction with Powerwerks products will not be allowed or honored. This warranty will be void if: A. The unit has been altered or modified. B. The serial number has been removed or defaced. C. The unit has been operated improperly. This warranty is subject to the following conditions and exclusions: Defects caused by wear and tear, misuse or neglect are not covered by this warranty.
EC Declaration of Conformity We: Kustom Musical Amplification INC. 3015 Kustom Drive Hebron, Ky 41048 Tel: 1-859-817-7164 Fax: 1-859-817-7199 Declare that the product Product name: Powerwerks Product model number: PW100BT to which this declaration relates is in conformity with the following standards; EN55013: 2001/+A1: 2003+A2: 2006 Limits and methods of measurement of radio disturbance characteristics of broadcast receivers and associated equipment.
PW100BT Personal PA OWNER’S MANUAL www.powerwerks.