User Manual

ManualsBrandsKuryakyn ManualsAccessoriesMTX Road Thunder Weather Resistant Motorcycle Sound Bar Plus: 300 Watt Handlebar Mounted Audio Speakers with Bluetooth, USB Power Charger, Satin Black

PAGE 1

302720

DPF-MRK-003 REV B 8/10/18

ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720

866 277 9598 | INFO@KURYAKYN.COM

454 COUNTY ROAD VV SOMERSET, WI 54025

KURYAKYN.COM

INSTALLATION INSTRUCTIONS

THANK YOU FOR CHOOSING KURYAKYN!

Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR MODERATE POTENTIAL INJURY.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN MAY NEGATIVELY AFFECT PRODUCT PERFORMANCE AND FUNCTIONALITY OR

DAMAGE THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING ATTACHED.

YOU WILL ALSO NEED:

Metric Hex, Allen wrenches, pliers

THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END USER RECEIVES THIS COPY AND IS AWARE

OF ITS IMPORTANCE FOR FUTURE USE.

WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED AT THE POINT WHERE IT IS

CONNECTED TO THE VEHICLE’S BATTERY. FAILURE TO DO SO CAN RESULT IN DAMAGE TO THE VEHICLE IF A SHORT CIRCUIT DEVELOPS

BETWEEN THE VEHICLE CONNECTION POINT AND THE PRODUCT.

ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:

1 Road Thunder Sound Bar Plus with

Wire Harness

1 Hardware Kit, containing:

2 M6-1.0 X 35MM Button Head Hex Screws

2 Sound Bar Mounting Clamps 2 M6-1.0 Lock Nut w/Washers

2 7/8” Clamps 2 M6-1.0 X 11MM Cap Screw Hex Drive

2 1” Clamps 2 M6 Split Washers

2 1-1/8” Clamps 2 M4-0.7 X 10MM Set Screws

2 1-1/4” Clamps 1 2MM Allen Wrench

1 USB Rubber Plug Seal 1 10 Amp Mini Fuse

1 Transparent Film 1 T-Tap Quick Connect Female

4 Cable Ties

1” CLAMP

1-1/8” CLAMP

1-1/4” CLAMP

7/8” CLAMP

2MM ALLEN WRENCH

TRASNPARENT FILM

CABLE TIES

SOUND BAR

MOUNTING CLAMPS

ROAD THUNDER

SOUND BAR PLUS

WIRE HARNESS

10 AMP

FUSE

M6-1 X

35MM BHHS

USB RUBBER

PLUG SEAL

M6-1 X

11MM CSHD

SPLIT

WASHERS

SET

SCREWS

T-TAP QUICK

CONNECTS

M6-1

LOCK NUT

CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S

AUTHORITY TO OPERATE THE EQUIPMENT.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720 THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
PAGE 2
INSTALLATION INSTRUCTIONS ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720 -CONTINUED- INTRODUCTION Thank you for purchasing this Kuryakyn Road Thunder Sound Bar Plus by MTX that is designed to work with most Bluetooth enabled devices including iPhone® and Android® smartphones and tablets. This easy to install and use, all in one unit is capable of transforming your Bluetooth enabled mobile device into the center of your vehicle’s audio system.
PAGE 3
INSTALLATION INSTRUCTIONS ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720 -CONTINUED- INSTALLATION SCENARIO 2 - INSTALL SOUND BAR, THEN MOUNTS CLAMPS TO HANDLEBAR. • Choose the correct size strap clamp for the handlebars. Note: Placing the transparent film between the strap clamp and handlebar will reduce the possibility of scratching the handlebars during installation. • Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them.
PAGE 4
INSTALLATION INSTRUCTIONS ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720 -CONTINUED- ELECTRICAL OPERATION Tap the Power button to turn the unit on. (Power, Ground, and Ignition wire need STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 to be connected to a 12V power source.) Tap the Power button to switch modes between Bluetooth and AUX. Hold the Power button for 2 seconds to turn the unit Off. The integrated fuse and ring terminals allow for easy wire connection to a 12V power source.
PAGE 5
INSTALLATION INSTRUCTIONS ROAD THUNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720 -CONTINUED- STEP 2 STEP 3 The Road Thunder Sound Bar Plus can be used with a second Road Thunder Sound Bar Plus unit. For the best audio performance, the second unit connected via Auxiliary should have the volume set to the max. The blue wire on the wire harness can be used as a remote turn on for the second audio device. CONTROLLING THE VOLUME The LED indicator light will blink in both Bluetooth and AUX modes at max volume.