M157-HLD(V)40-001 HDcctv Digital Video Dome Camera O PERATI O N M ANUAL VANDAL DOME PLASTIC DOME Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. EQUIPMENT AND ACCESSORIES 4. CAMERA COMPONENT DESCRIPTIONS • Plastic Dome / Vandal Dome Type 5. INSTALLATION • Plastic Dome / Vandal Dome Type 6. DIMENSIONS • Plastic Dome / Vandal Dome Type 7. SPECIFICATION 8. OSD FUNCTION DESCRIPTION CAUTIO N These servicing instructions are for use by qualified service personnel only.
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
3. EQUIPMENT AND ACCESSORIES Plastic Dome Type Mount Guide (Plastic Dome Type) Vandal Dome Type Mount Guide (Vandal Dome Type) Manual Screws(3ea) / L-Wrench Service Video Output Test Cable / Fixed Tape CAUTION • When you connect Service Video Output Cable WDR function does not work. • Service Video Output looks the angle of view narrower than HD-SDI Output.
4.
4.
5. INSTALLATION (Plastic Dome) 1. Attach the FLAT DOME on the ceiling with using the screws provided, considering the camera angle required for the surveillance function. 2. Adjust the LENS ANGLE to the desired location by hand. TAPPING SCREW (4 x 20L) - 3EA 3. Connect the VIDEO OUT CABLE and check the video image. Change the SETTINGS accordingly using the OSD controller.
5. INSTALLATION (Vandal Dome) 1. Attach the FLAT DOME on the ceiling with using the screws provided, considering the camera angle required for the surveillance function. 2. Adjust the LENS ANGLE to the desired ocation by hand. 3. Please remove the protective film when installing. TAPPING SCREW (4 x 20L)-3EA * Protective film 4. Connect the VIDEO OUT CABLE and check the video image. Change the SETTINGS accordingly using the OSD controller.
5. INSTALLATION • MONITOR CONNECTION - DC12V/AC24V DC12V/AC24V (TERMINAL BLOCK) DC12V POWER SUPPLY or AC24V POWER SUPPLY VIDEO IN BNC FEMALE MONITOR CAMERA - DC12V DC12V ADAPTER DC12V (DC JACK) MONITOR VIDEO IN BNC FEMALE CAMERA When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.
6.
7. SPECIFICATION PLASTIC DOME Image Sensor VANDAL DOME 1/3” 2.1 Mega Pixel SONY CMOS Effective Pixels 1984 (H) x 1105 (V) Unit cell size 2.8um (H) x 2.8um (V) Video output mode SDI: 1080P 30fps(25fps) / 720P 60fps(50fps) TV Out: CVBS NTSC/PAL Minimum Illumination 0.1 Lux S/N Ratio 50dB Auto / Manual selectable 1/30(25),1/60(50),1/120(100),1/250,1/700, 1/1K,1/1.6K,1/2.
8. OSD FUNCTION DESCRIPTION 1. EXPOSURE - BRIGHTNESS: Enable user to control the image brightness (0~20steps). - SHUTTER MODE: Enable user to set up the Shutter Mode. -> AUTO, MANUAL EXPOSURE - SHUTTER SPEED: Enable user to set up the Shutter Speed. -> 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K, > BRIGHRNESS SHUTTER MODE 1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K. SHUTTER SPEED *() is for power-frequency 50Hz. DSS AGC MAX - DSS(Digital Slow Shutter): INITIAL Enable user to set up the DSS Level.
8. OSD FUNCTION DESCRIPTION 4. DAY&NIGHT : Conversion of output image COLOR / BW depending on exterior environment. - D&N MODE 1. COLOR: Enable user to fit the output image in color. 2. B/W: Enable user to fit the output image in B/W.
8. OSD FUNCTION DESCRIPTION 6. SPECIAL : Setting up the CAM TITLE, LANGUAGE, PRIVACY, MOTION, DISPLAY, SYSTEM. SPECIAL > CAM TITLE LANGUAGE PRIVACY MOTION DISPLAY SYSTEM INITIAL RETURN - CAM TITLE : Enable user to choose any word in screen. (Maximum 10 letter is available) 1. A letter Choice from the screen using Menu key. 2. Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION. 3.
8. OSD FUNCTION DESCRIPTION - MOTION: Motion detection function. 1. RESOLUTION: Enable user to set up resolution 2. SENSITIVITY: Enable user to set up sensitivity. 3. WINDOW USE: Enable user to select to motion area. 4. WINDOW TONE: Enable user to area window tone. 5. X-POSITION: Window Horizontal start position. 6. Y-POSITION : Window Vertical start position. 7. X-SIZE: Window Horizontal width. 8. Y-SIZE: Window Vertical height. 9. INITIAL: Enable user to initialize setting of MOTION DETECT.