OPERATION MANY; CONTENTS Page Introduction Safety Precautions Package Before Use User Contort Adjustment Adjust The Picture Power Management System Image Adjustment Video Memory Modes A Note About The Video Memory Modes DOC {Display Data Channel} Specifications Federal Communications Commission Before Calling For Service Power Management PR EE IL 2282s
[rr Congratulations! You are naw the owner of our Color Monitor. To ensure proper operation, please carefully read this manual. After you've read this manual, keep it in a safe place for future reference. The model ls a inches viewable) intelligent microprocessor based monitor compatible with most analog RGE (Red, (Green, Bug) display standards, including (BM PC P32 Apple’, Macintosh, Centris®, Quadra® and Macintosh if family.
CER Cr 1S Disconnect the monitor from the main supply ¥ the monitor is not 1 be used for an extended period of time. Do not attempt to remove the back cover, 8s you will be exposed fo a shock hazard. The back cover should oily be removed by qualified service personal. Da not place objects on top of the monitor cabinet, which could fall into vents or which could cover them and prevent proper cooling of the monitors electronics.
Install the tit / swivel base = Place the monitor upside-down with the screen facing you. + Hold the base upside-down. + insertions hooks on the amiable into slots of monitor, Side the base award the front of the monitor(direction 13, oti the hooks licks into he locked position. + Push base toward direction 2 enlistee, moving base clockwise ar nail-clockwise until aligning the holes of the base and turntable, screw down.
Signal Cable Description: Front Panel Control Knob: DESCRIPTION. REC BLA POWER INDICATOR POWER SWITCH BRIGHTNESS: Tum knob to increase or decrease brightness CONTRAST: Tur knob to increases or desecrates contrast The huller knob {OSD function selection and adjustment) is located at the base of the monitor. User could make 2 good appearance of the monitor to suit personal preference by this knob.
Select the OSD menu 1.The OSD main menu {refer ta the following figure) is display on the screen when you press shuttle knob and tum shuttle knob. Rotation } Current Yoda Ode Dnt Trapezoid oral le Special; Def, | H Focus Aug. © Hl Locus Ks on AY Side Pin Bal. [A Cou Corner | Spin Corner A Moire Control = 2.Tum shuttle knob until the Jun of your defected fs highlighted, then press.
H-Size [a H-Position V-Size The bar graph shows you the current level of the selected “H-Size” control. Use the shuttle knob to increase or decrease the level to fit the screen or your desired size, draftees finished the adjustments you can go back to menu by pressing shuttle knob again. 5.The OSD window will automatically shut off afire about 5 seconds. 1 H-Size Turn shuttle knob to enlarge or reduce horizontal size.
21.Spin Comer Somme balance control. 22 Mike Control Moire Central Eee For the power saving feature to operate, the monitor must be used with either 8 PG having power saving circuitry or a PC running screen blanking software. The monitor has fee power-saving states, and the power saving operation Is indicated by the power indicator or: the front panel. When the power indicator is green, operation is normal.
§ Bose Modes 9-26 are empty and can accept new dived data 1 the monitor detects ohe of the above signals from your computer's video card, it will recall that mode and any stored image adjustments you may have made before If the monitor detects a new video made that had not been present before of is not one of the above listed factory presets, i will store 5 new mode automatically It ong of the blank empty) memory modes (in this examples, mode whence you now adjusted the controls to your preference, the imag
¥ you have used motifs 2B with 20 new video modes, and the monitor encounters S01 data wil replace the mode 10, with above method, when this monitor encounters new mode, it can update from made © to mode 28 sequentially and continuously.
¥ you have used motifs 2B with 20 new video modes, and the monitor encounters S01 data wil replace the mode 10, with above method, when this monitor encounters new mode, it can update from made © to mode 28 sequentially and continuously.
1. General Information SIZE Y-POSITION ROTATION ico: @ Notice: Design and specifications ars subject to change without active, and dot represent a commitment on the part of cur COMPARE.
Federal Communications Commission (FCC) This equipment hes been tasted and found to comply with the limits for & Class B digital device, pursuit to Part 15 of the FCC rules. Tress limits are designed to provide reasonable protection against harmful interference in a residential installation.