INSTALLATION GUIDE Esta™ Single Handle Lavatory Faucet KBF-1211 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List A B C D G E F A. Faucet Body B. Aerator C. Aerator Key D. Metal Washer E. Lock Nut F. Spanner Key G.
Diagram and Parts List-Lift Rod Drain n m a bh i j k l c o d e f g a. Waste Stopper b. Drain Flange c. Rubber Washer d. Concave Washer e. Metal Washer f. Mounting Nut g. Tail Pipe h. Top Hat Washer i. Drain Off Pole j. Washer k. Retaining Nut l. Clip m. Extender Rod n. Thumb Screw o.
Faucet Dimension 6 1/4" [159.2mm] 2 1/8" 3 7/8" 6 7/8" [98.0mm] 1 7/8" [47.8mm] 3/8” compression Installer Tip: 5 4 3/4" [120.3mm] M18.5X1.0-6g [63.3mm] 2 1/2" [175.0mm] [54.
Drain Dimension Ø2 1/8” [43.3-68.3mm] 1 3/4”-2 3/4” 8 3/4” [223.8mm] [Ø54.0mm] 1 1/4-18UNEF-2A 5 5/8” [141.6mm] Ø1 1/4” [Ø32.
Step 1: Remove lock nut Shut off the water supply. Remove the lock nut (E) from the faucet (A). A E Step 2: Installing the faucet Place faucet (A) through the hole in sink. Secure the faucet (A) to the sink using the metal washer (D) and lock nut (E) provided. Tighten lock nut (E) with spanner key (F) provided. Ensure the metal washer (D) and hoses are no interference.
Step 3: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug. Turn on angles stops and check for leaks (DO NOT TURN FAUCET ON) Step 4A: Installing the drain a Remove waste stopper (a) and drain flange (b) from tailpipe (g). Remove concave washer (d), metal washer (e) and monting nut (f) from drain flange (b).
Step 4B: Installing the drain b c Insert drain flange (b) through drain hole with rubber washer (c) attached. From underneath, place concave (d) and metal washer (e) on drain flange. Secure with mounting nut (f). Thread tailpipe (g) onto drain (b) and hand tighten. d e f g Step 4C: Installing the drain Insert waste stopper (a) into drain flange. Remove extender rod (m) and clip (I) from drain off pole (i). Reomve nut (k). Insert drain off pole (i) into drain pole opening of tailpipe (g). See insert 1.
Step 4D: Installing the drain Insert lift rod (o) through spout and connect with extender rod (m). Tighten thumb screw (n). Step 4E: Installing the drain Attach drain off pole (i) to extender rod (m) with clip (I).
Step 4F: Installing the drain Loosen thumb screw (n) on extender rod (m). Push down on lift rod (o) until stopper is in open position. Retighten thumb screw (n). Step 5: Flush faucet B C 11 After installing faucet, remove aerator (B) with included aerator key (C). Turn water on for 30 seconds to remove any debris. Reassemble aerator (B).
Replacement Parts Replacement Parts List Finish / Color 1 2 3 1. Cover Button 12 4 2. Set Screw KP27002 KP27001 3. Handle SFS, MB, GM, BG, SFSB* KP27150 4. Cap SFS, MB, GM, BG, SFSB* KP27151 5 6 GR, BL* Part # 5. Bonnet Nut KP27152 6. Screw KP27153 7. Cartridge KP27069 8. Aerator KP27051 8 9. Aerator Key KP27052 9 10. Metal Washer & Nut KP27225 11. Spanner Key KP27144 12. Hex Wrench KP27020 7 13 10 13. Lift Rod 14. Drain Assemble 15.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: PROBLEM CAUSE Leakage under the handle Bonnet nut (5) has come loose 10 Hexagon Nut 9 11 Aerator drips or has inconsistent water flow pattern 12 Water will not shut off completely ACTION Remove the cover button (1). Loosen set screw (2) with hex wrench (12). Remove the handle (3). Unscrew cap (4) (by hand only).
Codes/Standards Applicable: NSF/ANSI 372 LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1 1.2GPM 4.5L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (”Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered foe the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
