I N S TA L L AT I O N MA N UA L Aquila Single Lever Basin Faucet FUS-13901 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
7/8” (22mm) 19.7º 10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) 1 3/8” (35mm) ∅ 1 3/4” (∅ 45mm) Prior to Installation: ∅ 1 15/16” (∅ 50mm) • Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-7750703 for a replacement • Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
FUS-13901 Diagram and Parts List A. Faucet Body B. Base Metal Ring J I1 I2 I3 C. Base O-Ring D. Rubber O-Washer A B F. Mounting Screws G. Mounting Nuts C H. Hot & Cold Waterlines D E E. Metal U-Washer H I. Aerator Assembly I 1. Aerator Washer F I 2. Aerator G I 3. Aerator Cover J.
Lift Rod Drain Diagram and Parts List a. Waste Stopper b. Drain c. Rubber Washer 1 d. Concave Washer e. Plastic Washer 2 f. Mounting Nut 3 g. Tailpipe Washer 16 h. Tailpipe 4 i. Top Hat Washer 5 15 6 j. Drain Off Pole k. Washer l. Retaining Nut 7 8 9 10 1112 14 13 m. Extender Rod n. Clip o. Thumb Screw p.
Lift Rod Drain Dimensions 5
Step 1: Install mounting hardware and waterlines A B F G C H Step 2: Install faucet A B F FH H D E G Remove faucet, mounting hardware, and waterlines from the box. Remove mounting nuts (G) from mounting screws (F). Place faucet body (A) on a soft cloth, spout facing up. Secure hot & cold waterlines (H) at the base of the faucet (HANDTIGHTEN ONLY) A. Hot Side: Left B. Cold Side: Right Thread mounting screws (F) into faucet base, flat head up, and tighten with a Phillips head screwdriver until snug.
Step 3: Secure faucet A B B F H Install rubber O-washer (D) and metal U-washer (E), over waterlines (H) and mounting screws (F), from underneath the countertop or sink. Attach mounting nuts (G) to mounting screws (F) and tighten with adjustableHwrench or 10mm wrench until snug DF H E G Step 4: Connect waterlines to main valve H 7 Thread hot & cold waterlines (H) onto angle stops and tighten with adjustable wrench until snug.
Step 5: Install Drain • Remove waste stopper (a) from drain (b). Remove tail pipe (h), mounting nut (f ), plastic washer (e), and concave washer (d) from drain (b).b Remove retaining nut (l) and washer (k) from tailpipe c (h) d a b c d e f g i k g e l Installerf tip: Leave top hat washer (g) in tailpipe (h) h h • Install drain (b), with rubber washer (c) attached, into the drain hole.
a Step 5: Install Drainb c d e f g k i • drain (b). Make sure slot at end of waste stopper (a)dis facing the e f rear of the sink l h a b c Insert waste stopper (a) into b b c • Insert lift pole rod (p) through the hole in the back of the faucet body (a). Loosen thumb screw (o) band attach extender rodg (m) to lift pole h rod (p).
a Step 5: Install Drain b p o l j • Place one end of clip (n) on I 1 drain off pole (j). Insert drain off I2 pole (j) through desired hole ofI 3 extender rod (m). Place other end of clip (n) on drain off pole (j) n m Installer Tip: You may adjust the extender rod (m) to a desired height Step 6: Flush Faucet Remove aerator assembly (I). I1 I2 I3 Loosen aerator cover (I 3) with adjustable wrench. Remove aerator (I 2) and aerator washer (I 1). Turn water on for 1 minute to remove any debris.
Replacement Part List - FUS-13901 2 3 4 5 6 18 7 8 9 1 10 11 12 13 16 17 14 15 1. Metal Handle 2. Set Screw 3. Cover Button 4. Cartridge Cover 5. Locking Nut 6. Cartridge 7. Aerator Washer 8. Aerator 9. Aerator Cover 10. Base Metal Ring 11. Base O-ring 12. Rubber O-Washer 13. Metal U-Washer 14. Mounting Screws 15. Mounting Nuts 16. Cold Waterline 17. Hot Waterline 18. Hex Wrench Download the Kraus Care & Maintenance Guide at: http://www.kraususa.
Replacement Part List - Lift Rod Drain 10 1. Waste Stopper Hexagon Nut 9 11 2. Drain 1 12 3. Rubber Washer 13 4. Concave Washer 5. Plastic Washer 2 3 6. Mounting Nut 16 7. Tailpipe Hot Washer Cold Water Water 4 8. Tailpipe 5 9. Top Hat Washer 15 6 10. Drain Off Pole 11. Washer 7 12. Retaining Nut 8 9 10 1112 Close 25˚ 90˚ 14 13 13. Extender Rod 14. Clip 15. Thumb Screw 16.
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 13 CAUSE ACTION Leakage under the handle Locking nut (5) has come loose Remove cover button (3). Loosen set screw (2) with hex wrench (18). Remove metal handle (1). Unscrew cartridge cover (4) (by hand only).
Codes/Standards Applicable: NSF/ANSI 372 GREEN LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1M 1.2GPM 4.5L/min maximum TM Water Efficiency HELP LINE Our customer service hours are Monday – Friday, 9am – 8pm EST. Be sure to visit our website at www.kraususa.com If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.
R E G I S T E R Y O U R P R O D U C T T O D AY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit http://www.kraususa.com/registration We’re always looking for ways to improve. Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.