Installation Guide

ManualsBrandsKovacs ManualsChandeliersScale 6 Light 40" Wide LED Linear Chandelier

INSTALLATION INSTRUCTIONS

For item#P1466-695-L (Rev. 01/10/2020)

READ AND SAVE THESE INSTRUCTIONS

WARNI NG! S HUT POWER O FF AT F US E OR CI RCUI T BRE AK ER.

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

Fig. 1

Fig. 2

PREPARING FOR INSTALLATION (Fig. 1)

1. Shut off power at the fuse box or circuit breaker box and

remove the old fixture including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a

clean area. Take care not to misplace any small parts

necessary for installation.

3. Screw long metal rod (J) onto the threaded nipple (I) on top of

fixture.

4. Determine the desired hanging height and thread rods (F1,

F2 and F3) to the threaded nipple of the long metal rod (J).

Then screw loop (H1) onto rod (F1). Pass the wires carefully

through each rod as you assemble.

5. Attach the quick link (G) to loop (H1) and loop (H2) on the

canopy (E). Carefully feed the wire through loop (H1), quick

link (G) and loop (H2).

6. Position the mounting plate (C) on the ceiling and mark

location of the two mounting holes. Drill the appropriate size

holes on the ceiling and insert the plastic anchors (A).

7. Attach the mounting plate (C) to the junction box using

mounting screws (B) (Size: #8-32N*L0.5”). The side of the

mounting plate marked “GND” must face out.

8. Secure the mounting plate (C) by inserting the wood screws

(D) through the holes on the mounting plate into the plastic

anchors (A).

9. The support cable is provided to support the weight of the

fixture while wiring. Align the fixture to mounting plate (C) and

attach hook (P) on the end of support cable (N) into a slot

located on mounting plate (C). Carefully allow the support

cable (N) to support the weight of the fixture while wiring.

CONNECTING THE WIRES (Fig. 2)

10. Connect the electrical wires as shown in figure 2, making

sure that all wire connectors are secured. If your outlet has a

ground wire (green or bare copper), connect the fixture’s

ground wire to it. Otherwise, connect the fixture’s ground wire

directly to the mounting plate (C) using the green screw

provided.

11. Tuck the wire connectors neatly into the ceiling junction box

and then raise the canopy to the ceiling.

COMPLETING THE INSTALLATION (Fig. 1)

12. Place canopy (E) over the mounting plate (C) and secure it

with screws (F).

13. Place the glass shade (K) over metal cup (L) and secure with

three tabs (Q).

14. Secure the metal plate (M) onto the LED module by using the

screw (O).

Your installation is now complete. Return power to the outlet

box and test the fixture.

Note: Illustration (Fig. 1) on this manual is for installation

purposes only. It may or may not be identical to the fixture

purchased.

LA-3191E

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Set#A-021-320119

- Mounting Plate

- Ground screw

- Mounting Screw*2

Rod#W30-1-695*2(F1)

W30-1-695*4(F2)

W30-H-695*2(F3)

IMPORTANT: FIXTURE SHOULD BE INSTALLED

BY A QUALIFIED ELECTRICIAN TO ENSURE

PROPER WIRING AND INSTALLATION.

Dimmable with ELV and/or

LED compatible wall dimmer

switches.