Instructions / Assembly

kovaproducts.com Rev. 0.1 | 2020.02
FCC Notice
CAUTION: Changes or modications not expressly approved could void your authority
to use this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Changes or modications not expressly approved could void your authority to use this
equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
• Relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Pre-Installation
Tools Required (not included)
Gloves Safety goggles
Packing List
Part Description Qty.
A LED Downlight 1
B Installation sheet 1
C Ceiling Cutout Template 1
Product and Cutout Dimensions
D1
D2
3000K
L
3500K
M
4000K H
Size D1 D2 H
Min.
Cutout
Max.
Cutout
6 in. 8-7/16 in. 5-7/8 in. 4-7/16 in. ø6-1/8 in. ø7-3/16 in.
8 in. 10-1/16 in. 7-3/8 in. 4-3/4 in. ø7-9/16 in. ø8-11/16 in.
WARNING: Ensure the power is turned off.
Choosing Your CCT and Wattage
This xture allows you to select between three power and light temperature settings to
match a wide range of applications. The color tunable switch allows for CCT selections of
3000K, 3500K, or 4000K.
Color Tunable Switch
Color Tunable Switch
Power Tunable Switch
Power Tunable SwitchPower Tunable Switch
K0000019482 K0000019483
9W 13W 19W 16.5W 23W 29W
3000K
3000K
L
3500K
3500K
M
4000K
4000K
H
Retrot Installation
1. Choose your CCT and power
settings as described in the
“Choosing Your CCT and
Wattage” section.
2. If the existing lamp and trim are
present, remove from the ceiling or
move it out of the way as it will not
be needed during installation.
3. Measure the ceiling opening
to make sure the edge of the
downlight will cover the entire hole
and still sit rmly in the ceiling
before proceeding.
4. Attach the carabiner safety clip
on the downlight to the existing
xture housing.
5. Remove the junction box faceplate.
Disconnect all wires to the ballast
and remove the ballast from the
J-Box. Remove the appropriate
round knock out.
6. Insert the downlight conduit into
the J-box and wire to the power
source (black to hot, white to
neutral, violet to 0-10V dimming
positive, gray to 0-10V dimming
negative). Reattach the J-box cover
when done.
7. Squeeze the two spring clips on the downlight so they are in an upright position
and insert the downlight into the housing.
8. Once the downlight is inserted into the ceiling opening, release the spring clips.
Continue pushing the downlight into the housing until securely xed and ush
with the ceiling.
9. Restore power at the source. The installation is complete.
New Construction Installation
1. Choose your CCT and power
settings as described in the
“Choosing Your CCT and
Wattage” section.
2. If a new hole is needed, use a
hole cutter, and set the diameter
within the minimum and maximum
cutout ranges indicated in the table
to the left.
3. Attach the carabiner safety clip
on the downlight to a suitable
mounting point in the ceiling.
4. Insert the downlight conduit into
the J-box and wire to the power
source (black to hot, white to
neutral, violet to 0-10V dimming
positive, gray to 0-10V dimming
negative). Reattach the J-box cover
when done.
5. Squeeze the two spring clips on the downlight so they are in an upright position
and insert the downlight into the opening.
6. Once the downlight is inserted into the ceiling opening, release the spring clips.
Continue pushing the downlight into the ceiling opening until securely xed and
ush with the ceiling.
7. Restore power at the source. The installation is complete.
Product and Warranty Information
For product and warranty information please visit kovaproducts.com.
Safety Information
WARNING: To prevent electrical shock, turn power off at the fuse box before
installation.
WARNING: To prevent wiring damage or abrasion, do not expose wiring to edges of
sheet metal or other sharp objects.
WARNING: THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE
WHERE THE SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY AUTHORITIES HAVING JURISDICTION.
WARNING: Risk of re or electric shock. Installation of this retrot assembly requires
a person familiar with the construction and operation of the luminaire’s
electrical system and the hazard involved. If not qualied, do not attempt
installation. Contact a qualied electrician.
WARNING: Risk of re or electric shock. Do not alter, relocate, or remove wiring,
lampholders, power supply, or any other electrical component.
WARNING: Risk of re or electric shock. Install this kit only in the luminaires that have
the construction features and dimensions specied and where the input
rating of the retrot kit does not exceed the input rating of the luminaire.
WARNING: LED retrot luminaire conversion for use only with products described and
installed in accordance with the instructions provided with this retrot kit.
WARNING: Not for emergency lighting. TYPE IC INHERENTLY PROTECTED .
WARNING: Installation should be performed by a qualied electrician in accordance
with the National Electrical code and relevant local codes. Do not make
or alter any open holes in an enclosure of wiring or electrical components
during kit installation.
CAUTION: Wear gloves and safety glasses at all times when removing xture from
carton, installing, servicing, or performing maintenance.
CAUTION: Avoid direct eye exposure to the light source while it is on.
CAUTION: The recessed luminaire is intended for mounting only in a covered ceiling
where only the LED side of the luminaire will be exposed to damp or dry
locations. NOT FOR TOTALLY ENCLOSED LUMINAIRES.FCC Notice
INSTALL INSTRUCTIONS
Product
Dimmable Commercial Downlight
KPN Model Numbers
K0000019482 / K0000019483
6 in. Downlight Module / 8 in. Downlight Module