Use the 4A or V button of the cross key to move the cursor to the desired registration number {01 to 08), and then press the [SAMPLE] (Edit) button. A screen used to select the display conditions for the selected registration number is displayed. Use the & or V button of the cross key to move the cursor to a desired item and then press the [SELVES] button. Mes « Forth sating procedure and details of the rems, refer to page E-32 “Condition Setting”.
i Registering Conditions {Cod} Naming a Condition You can name a condition for easier management. [Setting Procedure] | From the condone screen, press the [MENU] tweet button. eR Beria The Menu screen is displayed. Co lac] Bask 1] 2 Make sure that “Edit Name” is selected, and IRE EE EE then press the [SELVES] button. San Ee The
Setting the Default Color Difference Tolerance (Tolerance (Dell) With the you can preset-and save tolerances which font depend on the tiger chlordane as de fault values. Deming measurement, just selecting the tolerance No. allows automatic judgment using the target colors and tolerances.
i Setting the Default Color Difference Tolerance (Tolerance (Def); 3 Use the 4A or V button of the cross key to move the cursor to the desired registration number {01 to 08). 4 Press the [SAMPLE] (Edit) button. A screen used to set tolerates for the selected registration number is displayed. Mere If registration number (1 {initial setting} is selected, or iff you select ano ber with which tolerances have already hen registered, a serene used to change the current tolerance sifting is displayed.
Setting the Default Color Difference Tolerance {Tolerance (Def) 1 Press the [SAMPLE] (Edit) button and change the setting. « When you select an item which is correctly checked md press the [SAMPLE] (Edit) button, the check mark is CMC cleared. When yon press the [SAMPLE] (Edit) button | eave again, the cursor moves to the setting value. Use the A or 7 button of the cross key fo change the value.
i Setting the Default Color Difference Tolerance (Tolerance (Def); Selecting Color Difference Tolerances You can set color difference tolerances to individual target colors when they are measured. You can also select one of the predefined tolerances {default tolerances) and use it for judgment Mary A default tolerance sifting can be registered with each registration number from 01 to 08.
Setting the Default Color Difference Tolerance {Tolerance (Def) 1 Deleting the Default Color Difference Tolerance Setting Delete the setting of the default tolerance of the selected registration number. [Setting Procedure] start the procedure from the screen. 1 Use the A or V button of the cross key to move the cursor to the registration number for which you want to delete the setting, and then press the [SAMPLE] (Edit) button.
i Setting the Default Color Difference Tolerance (Tolerance (Def); Naming the Color Difference Tolerance Setting [Setting Procedure] start the procedure from the screen. 1 E-64 Use the A or V7 button of the cross key to move the cursor to the registration number for which you want to edit the name, and then press the [SAMPLE] {Edit} button. A screen used to sel tolerances for the selected registration number Is displayed. Press the [MENU] button.
Setting the Default Color Difference Tolerance {Tolerance (Def) 1 Use the
i Other Settings Other Settings Setting the Display Language The display language can be changed from the factory-set language. Available languages are: English, Japanese, German. French, Spanish, Italian, and Chinese, (Mary The language is factory-set fo “English”. Naz) When the backup battery of the instrument has gone dead or the instrument & initialized (refer to page E72), the display kenning is reset fo English regardless af the set language.
Press the [SELVES] button, The =Calibration> screen is displayed in the selected language. # The figure shows an example when German (Den tech} is selected. Setting the Date and Time Other Settings 1 ELIOT nl TO TE 237020 QeBOBO7O A Begum) The has a built-in clock to record the date and time of measurement. Since the date and time have been set at the factory, you do not need to change therm under normal conditions. If necessary, you ean change the date and time settings.
i Other Settings 4 E-68 If you want to change the date format, move the cursor to “Format” and then press the [SELVES] button. The screen is displayed. [Mere Whiz step is unnecessary if you do not change the date format. Go to step 6 on the next page. Use the A or 7 button of the cross key to move the cursor to the desired format and then press the [SELVES] button. Fhe screen returns to the
Other Settings 1 Press the [SAMPLE] {Edit} button. The cursor moves to the position where the setting can be changed. o Use the A or W button of the cross key to change the varies. Nae Every fme you change the value of a block, you need te press the VESSEL] (OK) nation to confirm the change.
i Other Settings Setting the Power Save Mode The features a power save function which turns off the screen display and stops the power supply ta the flash circuit after no operation was made far a specified period of time. The period before the activation of the power save function can be set to 0 (OFF) or within the range from 1 to 60 minutes. Nga The power sue function is factory-set to OFF. [Setting Procedure] 1 Hold down the [MENU] button and press the maa Ten 7 button of the cross key.
Use the 4 or 7 button of the cross key to change the time before the power save mode is activated by specifying the number of minutes. Wars Holding down ihe 2 or 7 button of the cross key changes the value continuously. « When you finish changing the smelting, press the [TARGET] (Back) button to returnee to the «Settings green of the Option money. Settings 20: Disable the power save mode.
i Other Settings Initialization Reset the settings of the instrument to the initial status. Nas « Da sat initialize the instrument unless necessary. © The ensured dud, target color diet, tolerances set fo each target color and defoliant tolerance settings will be protected and not be deleted by initialization. © After rite initialization, the dispirit kenning is reset fo English. Change the Language §f necessary.
Measurement Ng = Prior ta stat af measurement, be sear fa perform white calibration. For details, refer to page B-29 “ White Calibration”. ~ To display color difference, i is necessary ta set target colors before ensnarement. © Far entreaty measurement, make sure fo keep measurement conditions {ambient temperature tee) constant. [Setting Procedure] 1 Press the [SAMPLE] button. The «Sample» screen is displayed.
Displaying the Measurement Results At the end of measurement, the measurement results will be displayed on the LED according theft specified measurement conditions. Typical measurement result screens are shown below. More You can switch the measurement result screens with the «J or [> button of the cross key. For details of the screen switching, refer to page E-78 “Switching the Display Contents of the Measurement Resulis™, Measured Data BB The figure below shows sample screen where “Abs.
| (— the Measurement Results Pass/Fail Judgment The following screens are displayed when “Judge” has been selected for “Dis. Type” of the current display conditions. + When he result was “Pass” The background is shown in green. (Rangoon | TES Sam eo « When the result was “Fad” The background iz shown in red. coat MAISIE Sample List [Tars eh Color Difference Graph The following screen ix displayed when “Graph Dif” has been selected for" Dis. Type” of the current display conditions.
Displaying the Measurement Results 1 « Color difference graph Ey 2 oe BCH 10° /D65 Temple List [Target AL* axis {color difference graph} Aa * axis {color difference graph) Ab axis {color difference graph) Measuring point Se ales for the axes Specified box tolerances Position of target color a B® DLCOO0S Spectral Reluctance Graph The following screen is displayed when “Graph Spec.” has been selected for “Dis. Type” of the current display conditions.
Displaying the Measurement Results 1 Table legend > © The screen is displayed. © The screen is displayed, but the result will be displayed; other measurement result will not be displayed. X The screen is displayed, but the item will not be displayed. Shadowed : The screen is not displayed.
| (— the Measurement Results Display order of the measurement result screens {when all the items are selected for “Dis. Type.
Measured Data Operation The following operations are available for the measured data. « Print: Print the measured data. = Delete: Delete the measured data. « Edit Name: Mae the measured data. + List: Specify the columns displayed for each sample data No. in the Hist. « Auto Target: Automatically select a target color with the smallest color difference for measurement. » Delete All: Delete all the measured data.
i Measured Data Operation Print Print the measured data. You need to establish a connection between the instrument and a Bluetooth printer in advance. iam If proper connection is not established, you cannot select “Print” on fhe scree [Operating Procedure] stat the procedure from the
Measured Data — 2 Use the <] button of the cross key to move the cursor to “OK” and press the [SELVES] button, Data will be deleted. Mere When date is deleted, the subsequent sample data Nos, will be signed, reducing them by one. Palate OK tw delete Sam «000272 re « When the deletion is complete, the screen returns to the «Menu screen. * When you price the cursor on “Cancel” and press the [BASELESS] button, the deletion ix canceled and the screen returns to the Mennen screen.
i Measured Data Operation Setting the List (List) ‘When the «Samples screen is displayed, pressing the [SELVES] button switches the screen between the list. display and detail display. Specify the columns displayed for each sample data No. in the list. [Setting Procedure] start the procedure from the
Measured Data — [Setting Procedure] start the procedure from the
i Measured Data Operation 2 E-86 Use the <] button of the cross key to move the cursor to “OK” and press the [SELVES] button, and the data is deleted. * When the deletion is complete, the screen re toms to the Mennen screen. « When you puce the cursor on “Cancel” and press the [BASELESS] button, the deletion is canceled and the screen returns to the
Average Measurement When taking measurements or setting target colors; more accounted-data can be obtained if the averaging defamation is used. With the CM-700d/6 00d, the following two averaging functions are available, « Manual Averaging : When the color of the specimen is nat uniform, measurements are performed at different positions on the specimen and then the average of the measured spectral reluctance data is calculated. This gives the avenge data of the entire specimen.
Make sure that & {Ready to measure} is displayed or Ready lamp is green, and then press the measuring button. The umber of completed measurements and the measured value will be displayed during measurement. (Mer To cancel the measurement, press the [TARGET] (Cancel) button. If canceled, the measurement will not be saved. Place the specimen measuring port at the next Average Measurement 1 TEAR Bl had . Marius i Ave. , 24 3 BOY BOE [ERE Su] Qos TEABAG position and repeat the steps from 110 3.
i Average Measurement Auto Averaging Measurement is repeated the specified number of times at the same position on the specimen and then the average of the measured spectral reluctance data is calculated. This will improve the intimacy of the measured data. The measurement procedure is ag shows below. Nazi Before starting ato averaging, you must complete the vitiates for auto averaging. Bor details, refer to page E48 “Auto Averaging (Auto Ave.) [Setting Procedure] 1 Press the [SAMPLE] button.
Pass/Fail Judgment for Color Difference You canst tolerances for the-color difference of the measured data from the upsetting color data to make pass/fail judgment. The uses box tolerances for judgment. The tolerances can also be set for “Cod the
i Pass/Fail Judgment for Color Difference E-92 Press the [MENU] button, The «Menu serene is displayed. Use the A or 7 button of the cross key to move the cursor to “Tolerance” and then press the [SELVES] button. The tolerances screen is displayed. To display the other tolerance sating items, press the A or 7 button of the cross key. Make sure that the values are sot properly, and then press the [SELVES] button. The «Target» screen is displayed. Press the [SAMPLE] button. The «Samples screen is displayed.
Pass Fail Indictment for Color Difference 1 7 Place the specimen measuring port on the specimen, and press the measuring button. The specimen is measured and the judgment results are displayed according to the display type specified for the display conditions. + When the display (ype is “Absolute” or “Abs. & Dif” The values winch failed the judgment are highlighted in red.
Connecting to an External Device The CM fixatives both USB and Bluetooth capability. You cay establish data Conn cation ar print data by connecting the instrument to a PC with the supplied USB cable IF-A17, or by connecting it to aPC or a printer via Bluetooth. NG When the instrument is exposed 10 strong external static electricity during communication with an external device, the communication may be interrupted.
Connecting to an External Device 1 [Operating Procedure] In general, a USE cable can be conmected/disconnected while the instrument is muted ON, however, yon need to turn OFF the instrument in the procedure below. 1 Turn OFF the instrument (Slide the Power switch to 2 Open the connector protection cover and connect the B connector of the USB cable to the USB connection terminal, 3 Connect the A connector of the USB cable to the USB port of the PC. + Fully insert the connector and ensure secure connection.
i ‘tormenting to an External Device Mao Fa nse the Bluetooth capability of ihe instrument fo connect a PC, you need to prepare both the instrument and the PC to establish Bluetooth communication. For details, refer to the instruction manual of the Bluetooth adapter. Preparation of the Instrument Set the Bluetooth capability of the instrument to ON. [Operating Procedure] 1 Hold down the [MENU] button and press the V button of the cross key. ‘The
Connecting to an External Device 1 Preparation of the PC Attach the Bluetooth adapter to the PC to enable Bluetooth communication. Ism The following describes a basic procedure. For @tails, refer to the instruction monaural of the Bluetooth adapter. [Operating Procedure] 1 Install the utility software supplied with the Bluetooth adapter on the PC. Attach the Bluetooth adapter to the USE port of the PC, and ensure that the PC properly recognize the adapter.
i ‘tormenting to an External Device 4 From the PC, search for Bluetooth devices and select {where is the serial number of the instrument)” from the listed devices. 5 Execute the “Bluetooth to serial ERO ee no eds ne connection”. When the connection is Com mu i cs established, the LCD display of the instrument shows “Communicating”. Connecting a Printer By connecting the instrument and a printer with Bluetooth capability, vou can print measurement results and other data from the printer.
Connecting to an External Device 1 Preparation of the Instrument Set the Bluetooth capability of the instrument to ON. Ins You cannot registers Bluetooth printer or set Auto Print until the Bluetooth comparability of the instrument is set to ON. [Operating Procedure] 1 Hold down the [MENU] button and press the 7 TE Th hee button of the cross key. I he Orion fo Meas. Lind. The «Option screen is displayed.
i Connecting to an External Device Establishing the Convection between the Instrument and Printer Set the instrument ax a host and establish a connection between the instrument and Bluetooth printer via Bluetooth communication. Naw Confirm the fallowing before starting the prove dare bestow. v The printer is turned ON and its Itinerary hus been filly charged. « The instrument is formed ON (Fhe Power switch 3 set to “V.
Confirm that “Search” is highlighted and then press the [SELVES] button. Available Bluetooth devices are searched for and the result is listed on the LCD screen. = From the list, find the Bluetooth address of the printer you checked during the procedure of page E-98 “Preparation of the Printer’.
i ‘tormenting to an External Device Printing Measured Data Print the meas wed data with the printer. Nas « You need fo establish the connection between the instrument and printer in advance. « The Bluetooth printer can print text data only. Note that pow cannot print graphs even when you selected spectral graph or color difference graph for the display pe for the instrument. [Operating Procedure] start the procedure from the screen where the measured data is displayed. 1 E-102 Press the [MENU] button.
Auto Print Connecting to an External Device 1 Print measurement results aromatically from the printer every time measurement 1s performed. Nas « You need fo establish the connection between the instrument and printer in advance. « The Bluetooth printer can print text data only. Note that pow cannot print graphs even when you selected spectral graph or color difference graph for the display pe for the instrument. [Printing procedure] 1 Hold down the [MENU] button and press the WV button of the cross key.
i Connecting to an External Device « Print Example 1 Display type is Graph Pee {spectral graph) « Print Example 2 Display type is Graph Diff (color difference graph). E-104 SAMPLE oral EN hare 1 A SEE Heir 13.58 © aa Aline Te Hae 9.80 © 1052 Se] B48 $i i] 4,486 8.55 Hong 485 8.44 Gen 8.12 Hygiene 4.47 0 me An Aen ga Sens 18.15 © 19.50 el] 3049 © EKED Er A340 © abd 536m 54.85 © ha she SRE BRE Senna S935 ad Seam S982 0 Bd S10 SR.27 © Be Hone e838 | Bal Sean BRAT ERE Ldn B20 85.
Connecting to an External Device 1 « Print Example 3 Display type is Judge. SALE al PARE The Name 1 scl 2.7085 2.40 Lx 774 1.30 ae RIB HA Del DBR. BLE de EER RB dae gel REY mis BAL 652 dep B13 B43 Hl g.8 8.81 SCE £ JUGS 2 {a HEE TRE aH BE eG PROBE LC PLAT doe B68 cha dae BEL CBE doe 8,55 3.56 ren 8.13 8.40 nl #81 8,81 as TER feat Wells « Print Example 4 Display type is Abs. & Diff. (absolute value & color IRE difference) Assessment (color assessment).
Displaying the Instrument Information Display the model titanic, version, and ministerial of the stringent. [Operating Procedure] 1 Hold down the [MENU] button and press the V button of the cross key. The
Error Messages The following messages may appear-while yon are using the instrument: 1 such shagginess app; talks the necessary actions shown in the table below. If the trouble does nat go away in spite of taking action, contact a MONICA MINOLTA SENSING-authorized service facility. Nai Messages flat may be displayed on he LCI are given dn the table below.
Embark Messages 1 ex seines Symptom Possible Caucus 1h ERGOT Charging for flashing of xenon lamp When batteries are used, replace them ERROR cannot be completed. with new ones. If this message is still IN CHARGING + Battery exhausted + Breakdown of charging circuit displayed after battery replacement, contact a MONICA MINOLTA SENSING-authorized service facility.
Troubleshooting If an abnormality hassock cured with the instrument, tale necessary actions ag given the table below. If the instrument still does not work proper, tum the power OFF, and then tum it ON again. If the symptom remedying, contact a MONICA MINOLTA SENSING-authorized service facility. heck Poll Action clomp LCD is blank. Are batteries inserted? Is the AC adapter connected? Insert the batteries. Connect the AC adapter.
Principles of Measurement Intercommunicating System This instrument utilizes the di: geometry nonconforming to CIE No. 15, MAST E1164, DIN 5033 Tell 7.180 7724/1. and JIS 28722-1982 (diffused illumination, $-degree viewing angle) standards, and offers measurement with autocratic SCI (secular component included) and SCE (secular component excluded) switching. The flow of measurement is shown below.
Principles of Measurement 1 [Rumination Area and Measurement Area The allows selection from two measurement areas. SAV (#3 mm) and MAV {48 mm), according to the specimen and applications. A Target Mask (illumination area} suitable for the selected measurement area must be attached to the instrument. EN With the CM-600d, only MAY ( § mem) is available, Target Mask {illumination area} The does not have » function to nationalistically detect whether the currently-attached Target Mask is for SAV or MAY.
i Principles of Measurement Initial Settings ** Initialization of the instrument will reset the settings to the initial values shown in the table below. The measured data, target color data and tolerances set for each target color are protected and not cleared by the initialization. * The zero calibration data will be reset to the factory-set data. 1f you performed zero calibration due to a change in the measurement environment, you will need to perform zero calibration again after the initialization.
5 « Specifications Add Mend CM ald did, de:8° {diffused illumination, S-degree viewing angle), SCI (secular component included SCE (secular component Telemetry excluded) delectable (with symptomatic-switching function) {Conforms to CIE No.
i Specifications Ohs er cation Spectral valves/graph, colorblindness values, color difference values/ Displayed data graph, FAITHLESS result, endocrinology, color assessment A, F10, F11, F12 {Simultaneous evaluation Ruminant with two ruminants possible} Observer 2°, 10° Hunter Lab, Yxy, XYZ, Mun sell, and color difference Color spaces in these spaces {except for Mun sell} MIL WI (MAST YI (MAST Cliometric data 11925), 150 Brightness.