User Manual

ManualsBrandsKondo Kagaku ManualsElectronicsRadio control transmitter

Table Of Contents

EX-2-manual-En-0530.pdf

① Bring distance of EX-2 and MiniZ close to about

10cm.

10cm

② Switch on MiniZ while pushing the setup button

of Mini-Z.

Pushing setup botton

Switch on

LED

③ After the Mini-Z's LED has lit up, release the

setup button. Then ｃ heck that the Mini-Z's LED

lights up again (indicating pairing completion)

① Switch o󱐯 MiniZ.

② Switch o󱐯 the EX-2 main power, then switch on

EX-2 again.

③ Bring distance of EX-2 and MiniZ close to about

30cm. Switch on the Mini-Z and check that the

receiver LED is lit. If the LED ashes, the Mini-Z

is not getting the EX-2 signal and the pairing

procedure should be repeated.

Preparing the Mini-Z

Preparations for Operation

● Pairing (For MHS Mini-Z)

ET2

↓

Case without the Xpansion unit

※ Refer to p.26 pairing Operation in the case of

using the Xpansion unit.

In order for the Mini-Z to operate, it must store the

transmitter's unique ID in its memory in a process

called “pairing.” Mini-Z must go through the pairing

process with the transmitter before being used for

the rst time.

※ Please adjust the Modulation mode

before pairing.(p.10) A receiver does

not work normally in di󱐯erent mode.

If the mode is changed（General or France), please

conduct pairing procedures with the Mini-Z you are

using again.

Preparing the Transmitter

① While pushing the ET2 lever up, power on.

② When the ET2 lever is released, the LED turns of

EX-2 LED lights up again (indicating transmitter

is transmitting the pairing signal.)

<France mode pairing ＞

FRANCE mode pairing is possible when the ET2

lever is released after LED turns o󱐯. Please use

this feature if the situation is needed.

Power ON

↓

Summary of content (15 pages)

PAGE 1
● Pairing (For MHS Mini-Z) Case without the Xpansion unit 2. Preparing the Mini-Z ※ Refer to p.26 pairing Operation in the case of using the Xpansion unit. ① Bring distance of EX-2 and MiniZ close to about 10cm. In order for the Mini-Z to operate, it must store the transmitter's unique ID in its memory in a process called“pairing.”Mini-Z must go through the pairing process with the transmitter before being used for the first time. 10cm ※ Please adjust the Modulation mode before pairing.(p.
PAGE 2
● Fail-Safe Setting Fail-safe is when the receiver loses the radio signal of the transmitter and the function keeps channel 2 (throttle) in an optional position. The configuration is usually full brake or neutral. Please be sure to set the fail-safe. If you change the position of the fail-safe operation, please set again. We recommend to set it again even if you modify the car engine brake linkage. This function works for only 2nd channel. 4 3 2 1 B Turn on the transmitter.
PAGE 3
■ Procedures Prior to Operation 1.Switching On After ensuring that it is safe to do so, switch on the transmitter followed by the receiver or Mini-Z. 2.Model Confirmation Confirm the model which will be used. 3.Checking Movements With the model's wheels lifted off the ground, operate transmitter to check for proper movement. While driving, use steering and throttle trims to make fine adjustments. Drive in a figure 8 pattern to check steering balance. Figure 8 Pattern Stand Trim 4.
PAGE 4
● Trim and Sub Trim Operation The sub trim is a convenient feature but it could also complicate the setting process if used incorrectly. Use the sub trim in the correct manner while also referring to the sub trim operation instructions on p.44 and p.49. 《Purpose of the Sub Trim》 When a servo is to be mounted onto a model, it is usually connected to the receiver temporarily to enable the transmitter to check its neutral position before it is installed.
PAGE 5
■ operating procedure ● STEERING ※ Other than the operation explanation of the steering wheel,the following function explanation is in the case of not using the Xpansion unit. Refer to p.43 operation in the case of using the Xpansion unit. ② Press and hold the ET1 lever to right, wait Left about 1 second. ET1 → Neutral MAX. ■ Steering wheel Turn steering in right and left, the servo (steering) connected to 1CH of the receiver works. Neutral Neutral Left MAX. Right MAX. Left MAX. Right MAX.
PAGE 6
● THROTTLE ※ Other than the operation explanation of the trigger movement, the following function explanation in case of not using the Xpansion unit. Refer to p.48 operation in the case of using the Xpansion unit. ■ Throttle travel ■ Throttle trigger ● Travel F(Forward) ① Hold throttle trigger full throttle. ② Push ET2 lever by 1 click, adjust the range of throttle movment angle. Quantity of the movement increases and decreases when operating the ET2 lever up or down respectively.
PAGE 7
● 3CH operation ● 4CH operation Operating the ET3 lever, controls the 3ch servo. When the button of BT1 is operated, it is possible to operate the signal of 4CH. ※ The funtion explaination is in the case when not using the Xpansion unit. Refer to p.33 operation in the case of assembled Xpansion unit. ※ The funtion explaination is in the case when not using the Xpansion unit. Refer to p.33 operation in the case of assembled Xpansion unit.
PAGE 8
■ Display and Control Method for attaching the Xpansion unit ● Basic Operations to Change Settings Operation Controlling of the setting adjustments is done via the L(<) key, R(>)key, ENTER(ENT) key, and BACK key. ENT Key: Selecting item to be modified; Confirming a change after a setting change. L（ < ）Key: Used to move cursor between menu choices and to change a setting value. Lowering a value (for L/R cases: raising toward L); Return to a previous menu item.
PAGE 9
● Installation of expansion unit ※ Not included with No.10555 EX-2 BASIC set. ▼ B：when mounting sideways Xpansion unit can be mounted facing the front or the side. The factory setting is mounted to the front. ① Attach the monitor base at a right angle to Xpansion Unit. ※ Different Factory setting. Attention to the marker. Be careful to not misuse the M2.6-6BH and TP2.68BH screws. P M2.6-6BH x2 Xpansioun unit can be mounted in two different directions using the monitor base and bracket..
PAGE 10
● Startup Screen and Initial Screen When the transmitter is switched on, the startup screen will display, followed by the initial screen. ※ Pressing the ENTER key during the startup screen will allow you to proceed to the initial screen. 【 Startup Screen 】 ① Version Information : Displays the version of the program that is installed in the Master Unit's CPU. This product's performance may be upgraded via paid or free upgrades. Check the KO Propo website for information regarding such upgrades.
PAGE 11
● How to change the Modulation mode ● VR information setting Adjust the steering and throttle resistance information. ※ Please perform the VR information configuration to calibrate your system. ○ When using EX-2 for the first time. ○ When changing a steering unit for a different product or when putting it back together. ○ When changing a grip unit for a different product or when putting it back together. ○ When using and confusion has occurred in the positional information. EX-2 has two Modulation modes.
PAGE 12
● Pairing (For general receiver) Case of using the Xpansion unit 3. Preparations for Operation ※ Refer to p.13 pairing Operation when not using the Xpansion unit. ① Switch off the receiver. ② Switch off the EX-2 main power, then switch on EX-2 again. In order for the receiver to operate, it must store the transmitter's unique ID in its memory in a process called“pairing.
PAGE 13
● Pairing (For MiniZ MHS) Case of using the Xpansion unit ※ Refer to p.13 pairing Operation when not using the Xpansion unit. 2. Preparing the Mini-Z ① Bring distance of EX-2 and MiniZ close to about 10cm. In order for the receiver to operate, it must store the transmitter's unique ID in its memory in a process called“pairing.”Even if a single transmitter is used to control multiple receivers, each receiver must go through the pairing process with the transmitter before being used for the first time.
PAGE 14
■ TOP MENU FUNCTION STEERING This an index which displays the 6 different function menus. This an index which displays the 6 different function menus. Model Menu (MODEL) Steering Travel Operations such as selecting or copying a model. Modify the overall amount of steering movement. Timer Menu (TIMER) Steering Trim Operating timer-related functions. Modify the neutral position of the steering angle.
PAGE 15
THROTTLE This an index which displays the 10 different function menus.(Separeted 2 pages.) Throttle Travel MENU1 Modify the maximum throttle movement. Jump menu to throttle menu1. Throttle Trim Brake Override Modify the neutral position of the throttle. Modify the maximum amount of braking and steering travel assigned to a switch. Throttle Turn Speed Throttle Reverse Modify the speed of the throttle's movement. Modify the throttle direction.