Instruction Manual
Conection of Receiver With Electrical Powered Car ●Motor ●Battery ●Transmitter (EX-10EURUS) ●Servo ●ESC (Speed Controller) ●Receiver(KR-409S) (CH1:Steering Servo CH2: ESC) With Gas Powered Car ●Battery for Receiver ●RF Module(RF-902S or RF-902SM) Attention! 4 ●Servo ●Receiver (KR-409S) (CH1:Steering Servo CH2:Throttle Servo) Please see the correspondence product table when using it excluding the equipment included in the set.
SAFETY PRECAUTIONS For the safe Usage of this Unit With the nature of radio controlled models, misoperation will result in danger. In order to avoid these circumstances and to use this unit safely, please read the contents thoroughly. Danger! Failure to observe the matter discussed in such an item poses a serious threat of death or severe injury.
Danger! Prohibited matters Danger! Enfoecement matters ●Do not allow any plastic parts to come in contact with fuel and exhaust. Doing so causes risk of damage. ●Be sure to confirm that the model memory is matched to the models currently running. Not doing so may cause the model to run out of control. ●When you make functional changes, be sure to stop the engine or disconnect the motor lead wire. Danger! Prohibited matters ●Do not touch the engine, motor, ESC where heat is generated.
NAME OF PARTS Transmitter(Front View) Hook ET1Lever LM2 LED indicator2 LM1 LED indicator1 LM3 LED indicator3 (-)Minus key (+)Plus Steering Wheel key JOG DIAL ET3 Lever 12x4 LCD Display ENTER Enter Key Power indicator BACK Key ET2Lever POWER Switch BT2 Throttle trigger ET4 Lever ET5 Lever BT1 Push Switch [Factory Setting] ET1:Steering Trim ET2:Throttle Trim ET3:Throttle Brake ET4:Steering ET5:CH3 control BT1:Not Assigned BT2:Not Assigned Battery Box(inside) �Adjustment of Steering Tension
Transmitter(backside view) RF Module CHARGING (Refer P.11) (Refer P.10) Phone Terminal (Refer P.8) D.S.C.(Direct Servo Control) Terninal.(Refer P.8) MultiAccessPort (Refer P.8) D.S.C.Terminal Because the DSC function is installed in this unit, the setting can be confirmed without putting out the electric wave. A D.S.C. cable (optional) is necessary to use this function. Receivers that will work with this function should be a KO Propo genuine product which is compatible with DSC. 1.
Setting of Wheel and trigger Adjusting the steering angle [Procedure] Hexagon socket head screw [Wheel inside] Hexagon socket wrench (2 mm) 1. Remove the sponge from the steering wheel. 2. Insert the hexagonal socket wrench (2 mm) into the two holes of steering Steering wheel wheel and tighten the hexagon socket head screws. 3. Attach the sponge to the steering wheel. 4. Referring to page 45, set "#ADJVOL" (adjust variable resistor).
PREPARATION FOR USING THIS UNIT How To Insert Batteries 1. Pressing in the direction of the arrow of(1). while pushing the part in the arrow of (2). Transmitter(bottom) Battery Cover 2. (1)The direction is matched to the display of the plus or minus of the dry battery box, and eight AA size batteries are put. (2)The direction of the terminal of the dry battery box and the terminal of the transmitter is matched and it pushes it into the interior. Contact (3)The battery cover is closed.
Changing the RF Module and Crystals Remove the RF module and replace them as required. When removing the RF module, push the right and left claws. Please exchange modules to change frequency band (2.4GHz,27MHz,40MHz). Coution! Turn off the power of this unit when Changing the RF Module and Crystals Coution! Please remove the rubber cap of the main body antenna, install, and use the antenna (optional) when you use 27MHz and 40MHz.
● Fixing receiver to carbon chassis When fixing the receiver to the chassis or on the mechanism deck, use more than 2 layers of doublesided tape to avoid direct contact with chassis. Chassis and mechanism deck (especially carbon material) can also conduct noise. Making space between receiver with them is recommend to ensure protection against noise. EE ISIS NNOO �Note receiver LED position when installing.
Unit preparation 1. 2. 3. 4. 5. Install receiver, servo, ESC (when using with electric car) and connect cables. Install receiver noting anti-noise measures. Read instructions included with servo and speed controller before connection and usage. IInstall batteries (R6/AA/UM3 size batteries x 8) to transmitter, then install running battery to electric R/C car. For gas R/C car, install Note polarity and install fresh batteries. Depleted batteries may deteriorate radio power and receiver batteries.
Failsafe setting Failsafe automatically returns throttle (2ch) in desired position (full brake/neutral) if the model may run out of control. full brake Switch transmitter on. Throttle trigger (full brake/neutral) Switch receiver on and check servo movement. Operate throttle trigger in brake/neutral position (transmitter memorizes the position) Hold set button of receiver more than 3 seconds. neutral Release after LED turns off.
SPECIFICATIONS Transmitter: KT-409H Operation method:Wheel + trigger method Number of channels:4 channels Transmission frequency range:Any frequency range is available by replacing the RF module Neutral pulse:1.5mSec Power supply:8xAA size dry cells or 8-cells battery pack Current consumption:Less than 80mA (high frequency range is not included) RF module:RF−902S or RF-902SM Modulation:DSSS Transmission frequency:2.
