Instruction Manual

Installing the Receiver Unit
Pairing operation of the transmitter
This product is for use only with the Kyosho MINI-Z EVO series.
*Be careful not to pinch the
antenna when installing
the receiver cover.
Align receiver unit with
connector on circuit board
side.
Receiver Cover
Receiver Unit
Align left and right
sides and click in.
LED Indicator
LED Indicator
Pairing Button
Pairing Stick
Prepare the pairing stick and
locate the LED indicator and
pairing button.
Use the pairing stick to
Press and hold the pairing button.
Preparing the receiver
PairingoperationoftheChassis
In the case of EX-NEXT
Set the RF mode to [MINIZ] and set the pairing mode.
*It cannot be used in radio wave modes other than [MINIZ].
In the case of MC-8
Enter the pairing mode in the same way as pairing with the MR-8.
Chassis(Switch)
When the LED indicator
lights up, release the
pairing button.
LEDIndicatorwillshowthefollowing.
LightisON:Pairinghasbeensuccessful.
Lightisflashing:Pairinghasnotbecompleted.
Switchthetransmitterandchassispower
offanddopairingagain.
Chassis (Switch)
Turn off the transmitter. The next time you turn it on, the
settings will take effect.
*In rare cases, pairing data may be lost, but this is not a
malfunction. Please set up the pairing again.
Pairing
*Please use EX-NEXT with Ver. 2.00.00 or later.
New pairing method
*Pairing is possible even when the MINI-Z
is turned on.
Press the BACK button on the EX-NEXT, turn off the power to
the MC-8, and turn on the power as usual to operate the MINI-Z.
Press the pairing button to turn on the LED indicator, and then
release the button to turn off the LED.
When the vehicle is turned on, the LED indicator will be in a
flashing state.
Set the EX-NEXT or MC-8 to pairing mode.
*Please refer to the transmitter's manual for the pairing procedure.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
response for compliance could void the user’s authority to operate the
equipment.
MINI-Z EVO Receiver Unit EX-NEXT
Ver.1.00
Instruction Manual
Thank you for purchasing this product. Before using the product, please also check this instruction manual and the instruction manual of
your transmitter. Due to product improvements, the contents of this manual are subject to change without notice. Please note.
For your safety
Please note the handling and use of this product.
Our company cannot owe responsibility from the nature of the radio control models
And the customer assumes all responsibilities that result from this product being used.
Warning
Attention
●Please avoid storage in a place of high temperatures and high humidity because it may cause the breakdown,damage and deformation of the product. ●Please note when using with an engine model,
place where exhaust and the waste oil will not come into contact with the product. *In case of submerging in oil or water, please send it out for repair. ●This product's performance is designed for use in
the shown specified usage which is based on this instruction manual and the instruction manual of the transmitter which is used. When the instructions are not understood, please contact our service
department for advise. ●After verifying the safety of use, think of all the accidents possible and please enjoy with responsibility.
This display shows the possibility or a substantially damaging accident can cause injury.
●This product is manufactured for surface use radio controls. *Discontinue use for all other purposes. Discontinue use in the
event of a thunder storm. *There is danger of a lightening bolt striking the antenna of the transmitter. ●Discontinue use when
consuming alcohol or medication that may hinder concentration or judgment. *Unexpected accidents are caused with a
judgment mistake. ●When rain and puddles are present, please discontinue use. *There are times when water enters into the
equipment and control will be lost. ●Only use the batteries specified in the instruction manual of the transmitter.
●To turn the system on, start by turning on the transmitter then the receiver. To turn off the system, turn off the receiver first, then the transmitter in this sequence. ●Please be sure to use only our products
for the transmitter and servos. *Concerning the damage and the like, which is generated when combining products that are not our company's genuine products we do not owe responsibility. ●Altering
the transmission module is inhibited by law and is subjected to penal code violations. Resolution remodeling of all products may result in the cause of a short and other accidents. In addition, if this
product is altered we will refuse repair service. ●Please do not use this product inside an airplane, hospital, near any automatic control equipment, medical electrical machinery and apparatus such as fire
alarms. In addition with respect to the law, if this product effects other radio equipment and electronic equipment, use must be discontinued at once.
The contents of this display shows a possibility of death or where a
serious injury may occur.
FCC statement
●About Repairs
When breakdown repair it is requested, please report the breakdown status in as much detail as possible. By noting the problem, repairs are performed quicker.
●When you believe you have a breakdown.・Please refer to your manual once more and please inspect. ・When you do not understand something, please inquire our service
department. ●When inquiring to our service department about a breakdown, please include in as much detail as possible of the contents mentioned below about your
problem. #Name of products (battery, car, transmitter & motor) used. #When breaking down, usage condition and description of breakdown condition. #Your address, name
and telephone number. When a repair is being requested, please be sure to send the memo which includes the above-mentioned contents in as much detail as possible.
KONDO KAGAKU Co., Ltd.
4-17-7 Higashi-Nippori, Arakawa-ku, Tokyo Japan
Phone : [phone]
https://www.kopropo.co.jp