Owner's Manual

OWNER'S MANUAL
PLEASE READ THIS OWNER'S MANUAL CAREFULLY
BEFORE USE. KEEP FOR YOUR REFERENCE.
Belt Clipt
(Back view)
Neck Strap hole
Function description
1. Batteries: Use 3 AA size batteries.""
2. Belt clip: The belt clip is attached for easy use.
3. LCD display: Displays current channel selection and
other radio status symbols.
4. button:Power/Scan
Press and hold the button to turn your unit on/off.
5. button:MENU/LOCK
Press the button to Channel and function
selector.
Press and hold the button to Lock/unlock the channel.
7. button:CALL/MON
Press button to CALL
Press and hold button to Monitor.
BATTERY INSTALLATION:
- Remove the belt clip by pulling the tab and sliding it up.
- Pull the battery door lock tab down to release the battery
cover. Insert 3 AA batteries.""
- Replace battery cover . Snap the lock tab and belt clip
back into place.
- To use the radio, you must install 3 AA size batteries.""
-Turn the volume up to an audible level.
- Set both units to the same channel.
- Press button to CALL
The other unit will make a 2 second call tone. They can
then respond to your call by either:
- pressing the PTT button and speaking into the radio, or
- Press button double times to CALL, which
activates a 2 second call tone on your radio.
Calling another radio
- Press the button until the current channel
Number flash on the LCD display.
- Press the button to move to a higher channel.
- Press the button to move to a lower channel.
-Press the PTT button to choose the desired
to normal mode, or press the button to next menu.
The walkie-talkies has multi-channels. To change channels:
Low battery indicator
When the batteries need to be changed, the battery level
icon will flash. To ensure uninterrupted communication,
Recharge or replace the batteries as soon as possible.
.
Component Guide Function description
Getting started Operation Operation
Operation
2 WAY RADIO UP TO 5MILES RANGE Manual
.
Setting the Subchannels
To avoid disturbing signals nearby ,the walkie-talkie has 121 subchannels
-Press the buttton until the channel number flash on the display
- press the button until the subchannels in the
corner of the display begins to flash
- press the or buttons to switch between the 121 subchannel.
- Press and PTT button to confirm the subchannel.
-To deactivate a subchannel,press the Menu button and press
the or buttons until of is shown in the display.
- press the PTT button to confirm,
upper right
“”
or press the button to next menu
.
Setting The VOX function
The vox function reacts to voice and sound
Do not use the function if you are in surroundings with storng
winds or a lot of noise .
-Press the buttton until the channel number flash on the display
-Press the two times.The VOX function will be shown in the display
-Press the or button to adjust senditivity to sound
(3=most sensitive to sound).
-To deactivate the VOX function,Press the the or button,until
of is shown in the display
-Press the PTT button to confirm,The walkie talkie
now retums to normal function
“”
Setting the call ring melody
The walkie talkie has 10 different ring tones
-Press the button three times until the numbers
begin to flash in the upper right corner of the display.
-
Press the PTT button to confirm
-Press the buttton until the channel number flash on the display
Press the or button select your call ring melody. .
-
to
To deactivate call,and press the or buttons until of
is shown in the display.
“”
.
Setting the Channels
Setting the button tone
-
Press the buttton until the channel number flash on the display
-Press the button four times until the numbers
-Press the or button to select on or of .
-Press and hold PTT button to confirm
“” “”
Setting the PTT tone
-Press the buttton until the channel number flash on the display
-Press the button five times until the numbers
-Press the or button to select on or of
-Press and hold PTT button to confirm
“” “”
Turning the unit ON
Press and hold the button. The unit will beep and the
LCD display will display the current channel.
Press and hold the button,The unit will beep and the
LCD display will turn blank.
-Press the button to increase the speaker volume.
-Press the button to decrease the speaker volume.
-The speaker volume level is indicated by the number .
-When the walkie-talkie is switched on and not being used for
speech or paping,it is always in the receiving mode .
-Pressing the PTT buttons automatically overrides and turns
off the receiving mod
.
Turning the unit OFF
Adjusting the speaker volume
Receiving Communications
OWNER'S MANUAL
(GT-60)
Monitor
Lock
Menu
Lamp
Scan
Lamp
Channel number.
subchannel (1-121)-
- vox function activated (sound sensor)
Press the button to search for channels.
6. UP DOWN button:
Press the button to adjust the volume level and to
change channels
8. button:LAMP
Press and hold button to until sending light.
Press and hold button to until off light.
Press PTT button to transmit.
9. button:PTT
11.
Charge Jack :The device can support the Micro USB
charging (5V, 1A). It is compatible with most of 5V
smartphone charger on the market.
Figure 1
Figure 2
Figure 3
Channel and return
,
or press the button to next menu
.
Momentary monitor:
- This feature turns off the automatic squelch feature, either
momentarily or continuously. It helps in receiving signals
to its maximum range, but may pick up static signals, too.
- Press and hold button until a beep sound is heard
- Release the button to restore the automatic squelch.
CHANNEL LOCK:
- This feature locks the channel so that the channel cannot
be changed accidentally.
- To lock the channel, press and hold buttons until a beep
sound is heard.The lock symbol will appear on the display.
Buit-in flashlight
As an added feature,your has a built-in flashlight that
can be used in sending light signals or for your lighting needs.
walkie talkie
-press and hold LAMP buttons until sending light
-press and hold LAMP buttons until off light
PTT
Display of the current battery level.
Transmitting icon, displayed when transmitting a signal.
Display of current volume.
Displayed during the Channel Scan mode.
Keyboard is locked.
- To unlock the channel, press and hold buttons until a beep sound
is heard. The lock symbol will disappear.
Charging the radio
To charge required using 3 AA NI-MH rechargeable ,
Insert the adapter's microUSB plug to DC IN 5V USB jack
Charge the batteries for 12 hours and remove the radio after charging.
10.SPK/MIC Socket: It is compatible with 2.5MM external
earphone/microphone. It is excluded in package. It need
to purchase separately.
3