Installation Guide

Miter Box
32 Teeth Per Inch Blade
Masking Tape
100% Silicone Sealant
1/16"
3/16", 5/16"
5/6" Masonry Bit for Tile
1046213-01** [57" (1448 mm)]
1046213-02** [69" (1753 mm)]
1046213-03** [73-11/16" (1872 mm)]
Wall Jamb
1051142-A
Screw #8-32 x 3/8"
1077763-A
Bolt
1050047
Roller
1050048-A
Blind Nut
1053530
Insert
1044591-02** [48" (1219 mm)]
1048237-02** [48" (1219 mm)]
1048237-01-BDS [60" (1524 mm), K-702217-L-SHP only]
1048237-01** [60" (1524 mm)]
Bottom Track
1044729**
Center Guide
1048208-C
Screw #8-18 x 1-1/2"
1056868-A
Screw
1057704-02**
[20" (508 mm)]
1057704-01**
[24" (610 mm)]
Towel Bar
1086620**-* (K-702205)
1086622**-* (K-702207)
1086621**-* (K-702209)
1092738**-* (K-702217)
Inside Panel
1093027
Spacer (8 ea.)
Wall Jamb*
1050050
Bushing
1044183-01**
Hanger
1054347-01** (K-702205)
1054347-02** (K-702207)
1054347-03** (K-702209)
1054347-04** (K-702217)
Top Track
1044182** Hanger Bracket Kit
1031943**
Screw Cover
1131842**
Bumper
1077762
Anchor
Series Number Label
1053276**-* (K-702205)
1053277**-* (K-702207)
1053278**-* (K-702209)
1092737**-* (K-702217)
Outside Panel
1046794 Hardware Skin Pack
Length =
A - 1-1/8" (29 mm)
A A A
1-1/8" (29 mm)
Groove
1
2
3
x2
x2x2x2
x2
#8-18 x 1-1/2"
Screw
Cover
Screw Cover
Leg
B
"B" Mark
Cut Line
1/32" (1 mm)
B
Top Track
Contoured (Rounded)
End
Square End
Reversible
Measure distance “A.” Subtract 1-1/8” (29 mm)
from “A” and cut the bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Center the bottom track on the ledge with the
leg to the outside. Tape the bottom track in place
and mark the position.
Important! The bottom track and wall jambs
must sit flat against the shower ledge and the
walls. If needed, use the contoured ends of the
wall jambs for rounded shower corners.
Position the wall jambs between the bottom
track and shower wall. Plumb both wall jambs.
Mark the screw holes.
Remove the wall jambs. Drill 5/16” holes into
the walls and insert the anchors.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
Reposition both wall jambs. Secure the wall
jambs with screws. Attach a bumper at the top
and bottom locations.
Measure distance “B” above the wall jambs.
Subtract 1/32” (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.
Position the top track over the wall jambs. Either
side of the top track may face out.
Sliding Shower and Bath Doors
Walls must be within 3/8” (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions for application and
curing time.
For care and cleaning and other information; visit
http://www.kohler.com/clean
Sliding Shower DoorsSliding Bath Doors
11241256-2-A
1241256-2-A
Installation and Care Instructions
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Required Tools Parts Identifi cation
2 3 4
7 86 9
5
10
K-702205, K-702207, K-702209, K-702217
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
NOTICE: Do not touch the edges of the tempered glass with tools or any
other hard objects. Do not set the unframed tempered glass directly on the
floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
USA/Canada: 1-800-4KOHLER
México: 001-800-456-4537
kohler.com
1