Installation Guide

ManualsBrandsKOHLER ManualsBathRevival 3-3/4 in. Pedestal Sink Basin in White

115988-2-AA (B)

1998 Kohler Co.



REVIVAL



PEDESTAL LAVATORIES

All information in these instructions are based on the latest

product information available at the time of publication.

Kohler Co. reserves the right to make changes in product

characteristics, packaging, or availability at any time without

notice.

BEFORE YOU BEGIN

These instructions are for installing the lavatory to wood

frame construction. For other installations, supply suitable

bracing and fastening devices of sufficient size and strength.

Make sure you refer to the proper roughing-in drawing when

installing the lavatory.

IMPORTANT: Make sure that the wall and floor are square

and plumb to ensure proper installation.

REQUIRED MATERIALS/TOOLS

 Level

 Drill with 1/4” bit

 9/16” wrench

 Framing square

 Vise grip pliers

 Channel lock pliers

 Tape measure

ORDERING INFORMATION

K-2011 Pedestal lavatory w/transitional pedestal

K-2013 Pedestal lavatory w/traditional pedestal

TABLE OF CONTENTS

K-2011 Refer to Fig. #1 for Roughing-in;

proceed to Page 4 for installation.

K-2013 Refer to Fig. #2 for Roughing-in;

proceed to Page 4 for installation.

Summary of content (8 pages)

PAGE 1
REVIVAL PEDESTAL LAVATORIES All information in these instructions are based on the latest product information available at the time of publication. Kohler Co. reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. BEFORE YOU BEGIN These instructions are for installing the lavatory to wood frame construction. For other installations, supply suitable bracing and fastening devices of sufficient size and strength.
PAGE 2
ROUGHING-IN DIMENSIONS K-2011 K-2011-8 14-1/2” 4” FINISHED WALL 2-1/4” 2-7/8” 8-1/4” 11-3/16” 17-7/8” FINISHED WALL 1/2” D. MOUNTING HOLE IN PEDESTAL 23-7/8” K-2011-4 4” 8-1/2” 2-1/4” (T) 4-1/2” (S) 7-5/8” 1/2” D. ANCHOR HOLES IN LAVATORY 3/8” HOT 1-1/4” OUTLET (S) 5-3/8” 34” K-2011-1 2-1/4” 3/8” COLD 4” Fig.
PAGE 3
ROUGHING-IN DIMENSIONS K-2013 K-2013-8 14-1/2” 4” FINISHED WALL 2-1/4” 2-7/8” 8-1/4” 17-7/8” FINISHED WALL 1/2” D. MOUNTING HOLE IN PEDESTAL 23-7/8” K-2013-4 4” 8-1/2” 2-1/4” (T) 4-1/2” (S) 7-5/8” 1/2” D. ANCHOR HOLES IN LAVATORY 3/8” HOT 1-1/4” OUTLET (S) 4-3/8” K-2013-1 34” 2-1/4” 3/8” COLD 4” Fig.
PAGE 4
INSTALLATION K-2011, K-2013: Rough-in the supplies and drain piping according to the roughing-in dimensions illustrated, see Pages 2 and 3. NOTE: Control stop handle when in full open position must not extend more than 4” from finished wall. Install sufficient backing behind the finished wall for anchoring devices. For K-2011: locate the pedestal mounting hole 11-3/16” from the finished wall and on the centerline of the lavatory. NOTE: Do not drill floor anchor hole for pedestal at this time.
PAGE 5
Before installing the lavatory, attach the faucet and drain fittings. RECOMMENDATION: Attach valve bodies before spout. Make sure that the 1-1/4” tailpiece is installed to the drain body. Attach U portion of P-trap to tailpiece. Refer to faucet and drain manufacturer’s instructions. NOTE: Do not fully tighten the slip-joint connection. Set the pedestal mounting hole over the floor-mounted hanger bolt.
PAGE 6
IMPORTANT CONSUMER INFORMATION C. LIMITED ONE-YEAR WARRANTY A. CARE AND CLEANING Kohler plumbing fixtures and fittings are warranted free of manufacturing defects. Kohler Co. will, at its election repair, replace, or make appropriate adjustment where Kohler Co. inspection discloses any such defects occurring in normal usage within one year after installation. Kohler Co. is not responsible for installation costs. To obtain warranty service, contact Kohler Co.
PAGE 7
115988-2-AA (B) 7 Kohler Co.
PAGE 8
115988-2-AA (B) 8 Kohler Co.