Installation Guide

ManualsBrandsKOHLER ManualsShower Doors702207-L-NX

Miter Box

32 Teeth Per Inch Blade

Masking Tape

100% Silicone Sealant

1/16"

3/16", 5/16"

5/6" Masonry Bit for Tile

1046213-01** [57" (1448 mm)]

1046213-02** [69" (1753 mm)]

1046213-03** [73-11/16" (1872 mm)]

Wall Jamb

1051142-A

Screw #8-32 x 3/8"

1077763-A

Bolt

1050047

Roller

1050048-A

Blind Nut

1053530

Insert

1044591-02** [48" (1219 mm)]

1048237-02** [48" (1219 mm)]

1048237-01-BDS [60" (1524 mm), K-702217-L-SHP only]

1048237-01** [60" (1524 mm)]

Bottom Track

1044729**

Center Guide

1048208-C

Screw #8-18 x 1-1/2"

1056868-A

Screw

1057704-02**

[20" (508 mm)]

1057704-01**

[24" (610 mm)]

Towel Bar

1086620**-* (K-702205)

1086622**-* (K-702207)

1086621**-* (K-702209)

1092738**-* (K-702217)

Inside Panel

1093027

Spacer (8 ea.)

Wall Jamb*

1050050

Bushing

1044183-01**

Hanger

1054347-01** (K-702205)

1054347-02** (K-702207)

1054347-03** (K-702209)

1054347-04** (K-702217)

Top Track

1044182** Hanger Bracket Kit

1031943**

Screw Cover

1131842**

Bumper

1077762

Anchor

Series Number Label

1053276**-* (K-702205)

1053277**-* (K-702207)

1053278**-* (K-702209)

1092737**-* (K-702217)

Outside Panel

1046794 Hardware Skin Pack

Length =

A - 1-1/8" (29 mm)

1-1/8" (29 mm)

Groove

x2x2x2

#8-18 x 1-1/2"

Screw

Cover

Screw Cover

Leg

"B" Mark

Cut Line

1/32" (1 mm)

Top Track

Contoured (Rounded)

End

Square End

Correct Incorrect

Measure distance “A.” Subtract 1-1/8” (29 mm)

from “A” and cut the bottom track.

Position the bottom track on the center of the

ledge. If needed, file the ends to match the

corners.

Center the bottom track on the ledge with the

leg to the outside. Tape the bottom track in place

and mark the position.

IMPORTANT! The bottom track and wall

jambs must sit flat against the shower ledge

and the walls. If needed, use the contoured ends

of the wall jambs for rounded shower corners.

Position the wall jambs between the bottom

track and shower wall. Plumb both wall jambs.

Mark the screw holes.

Remove the wall jambs. Drill 5/16” holes into

the walls and insert the anchors.

Apply silicone sealant in the groove on the

underside of the bottom track. Secure the bottom

track to the ledge along the marked location.

Reposition both wall jambs. Secure the wall

jambs with screws. Attach a bumper at the top

and bottom locations.

Check the bumpers for the correct horizontal

alignment with the wall jambs.

Measure distance “B” above the wall jambs.

Subtract 1/32” (1 mm) or the width of a saw

blade from “B.” Mark and cut the top track.

Sliding Shower and Bath Doors

Sliding Bath Doors

Sliding Shower Doors

11241256-2-B

1241256-2-B

Installation and Care Instructions

Required Tools Parts Identiﬁ cation

2 3 4

7 86 9

K-702205, K-702207, K-702209, K-702217

USA/Canada: 1-800-4KOHLER

México: 001-800-456-4537

kohler.com

WARNING: Risk of serious injury. Damage prior to installation can

result in glass shattering. Inspect the glass and all parts for damage

before installation.

WARNING: Risk of serious injury. Improper installation can result

in glass shattering. Follow all installation instructions.

WARNING: Risk of serious injury. Do not cut tempered glass.

Tempered glass will shatter if cut.

WARNING: Risk of serious injury. Shower door and side panels

can shatter. Regularly inspect the glass and all parts for damage,

missing, or loose parts.

WARNING: Risk of serious injury. Always wear safety glasses

while cutting and drilling.

IMPORTANT! Do not touch the edges of the tempered glass with tools or

any other hard objects. Do not set the unframed tempered glass directly on

the floor or any hard surface.

IMPORTANT! Leave this manual for the end user.

Read these instructions before installing or using this product.

IMPORTANT! Do not cut the top track the same length as the bottom track.

NOTICE: The warranty does not apply to a product that has been modified

or altered in a manner other than as expressly permitted in the Installation

and Care Guide.

Walls must be within 3/8” (10 mm) of plumb.

Cover the drain with tape to avoid loss of small parts.

Follow the silicone sealant manufacturer’s instructions for application and

curing time.

To watch this installation video online, visit www.kohler.com.

For care and cleaning and other information; visit

http://www.kohler.com/clean.

Critical Information!

Read Before Installation!

Read and follow all instructions.

*Need help? Contact the KOHLER Customer Care Center

at 1-800-4KOHLER (1-800-456-4537).

For service parts information, care and cleaning, and

other information, visit www.kohler.com/serviceparts.

**Finish/color code must be speciﬁ ed when ordering.

Retain this document for future servicing.

Record model number from box for reference.

Model Number:______________

Summary of content (6 pages)

PAGE 1
Installation and Care Instructions Sliding Shower and Bath Doors K-702205, K-702207, K-702209, K-702217 1241256-2-B Required Tools Parts Identification 1044182** Hanger Bracket Kit *Need help? Contact the KOHLER Customer Care Center at 1-800-4KOHLER (1-800-456-4537). For service parts information, care and cleaning, and other information, visit www.kohler.com/serviceparts. **Finish/color code must be specified when ordering. Retain this document for future servicing.
PAGE 2
11 Position the top track over the wall jambs. Either side of the top track may face out. 12 Lift the inside panel onto the inside track. The label faces the outside of the shower. 13 Lift the outside panel onto the outside track. The label faces the outside of the shower. 14 If either panel needs adjustment, remove the door and position the rollers in new holes to raise or lower the glass. 15 Measure and mark the center of the bottom track.
PAGE 3
Instructions d'installation et d'entretien Portes coulissantes de douche et de baignoire K-702205, K-702207, K-702209, K-702217 1241256-2-B Outils requis Identification des pièces *Besoin d'aide? Appeler le centre de services à la clientèle de KOHLER au 1-800-4KOHLER (1-800-456-4537). Pour tout renseignement sur les pièces de rechange, l'entretien, le nettoyage, et autre, visiter le site www.kohler.com/serviceparts. **Les codes de finition et/ou de couleur doivent être fournis au moment de la commande.
PAGE 4
11 Positionner le rail supérieur sur les montants de mur. N'importe lequel des côtés du rail supérieur peut être tourné vers l'extérieur. 12 Soulever le panneau intérieur pour le poser sur le rail intérieur. L'étiquette est placée vers l'extérieur de la douche. 13 Soulever le panneau extérieur pour le poser sur le rail extérieur. L'étiquette est placée vers l'extérieur de la douche.
PAGE 5
Instrucciones de instalación y cuidado Puertas corredizas de bañera y de ducha K-702205, K-702207, K-702209, K-702217 1241256-2-B Herramientas requeridas Identificación de piezas 1044182** Kit de soporte de suspensión *¿Necesita ayuda? Comuníquese con el Centro de Atención al Cliente de KOHLER al 1-800-4KOHLER (1-800-456-4537). Para obtener información acerca de piezas de repuesto, cuidado y limpieza, y otro tipo de información, visite www.kohler.com/serviceparts.
PAGE 6
11 Coloque el carril superior sobre las jambas murales. Cualquier lado del carril superior puede quedar hacia fuera. 12 Levante el panel interior sobre el carril interior. La etiqueta debe quedar hacia el exterior de la ducha. 13 Levante el panel exterior al carril exterior. La etiqueta debe quedar hacia el exterior de la ducha. 14 Si alguno de los paneles requiere ajuste, retire la puerta y coloque las ruedas en orificios nuevos para subir o bajar el vidrio.