User Manual

ManualsBrandsKoden Electronics ManualsElectronicsMarine Radar RA42C

5.3 Basic Operations

xxx = keys to press

5.3.1 Powering On and Off

POWER

Press "POWER"key to power on.

2 minutes timer and "RADAR OFF" are displayed.

Keep pressing "POWER" key to power off.

Press the "BRIL" key.

BRILL

Control bar is indicated on the screen.

brilliance

Up/Down

Select brilliance.

Control knob

Adjust brilliance with knob

key backlight

Up/Down

Select key backlight.

Control knob

Adjust key backlight with

knob

ENT Press "ENT"key to return.

Radar turns into "ST'BY"mode when 2 minutes timer is finished and

"ST'BY" is displayed.

5.3.2 Transmitting

POWER

Press "POWER" key to

operate, radar picture

appears on the screen.

Another press "POWER" key,

radar turns to stand-by

mode.

Keep pressing "POWER" key more than 3 seconds, radar

turns to power off.

RANG UP

Pressing "RANGE UP" key produces a long-distance range,

RANGE DOWN

"RANGE DOWN" key a short-distance range.

.75

.25

BRILLIANCE 50

1:58

RADAR OFF

KEY BACK LIGHT 4

D‚V‚T

D‚Q‚T

‚g‚t

SCREEN

POWER

START

CHANGE

RANGE

Summary of content (5 pages)

PAGE 1
5.3 Basic Operations xxx = keys to press 5.3.1 Powering On and Off POWER ON POWER Press "POWER"key to power on. 2 minutes timer and "RADAR OFF" are displayed. Keep pressing "POWER" key to power off. SCREEN BRILL Press the "BRIL" key. Control bar is indicated on the screen. .75 .25 HU brilliance Select brilliance. Up/Down key backlight 1:58 OFF Adjust brilliance with RADAR knob. + Select key backlight.
PAGE 2
5.3.3 Adjusting brilliance of screen and key-backlight xxx = keys to press (1) Press the "BRILL" key. (Bar and figure indicating brightness, and figure indicating backlight appears on the screen.) (2) Select brilliance or key-backlight with the up-down cursor. (3) Adjust each item with the control knob. (4) When the adjustment is finished, press either the "BRILL" key or the "ENT" key to exit from the adjustment screen. (Pressing some other key after adjustment will lead to the function of the pressed key.
PAGE 3
controls return to manual state. Use when find navigation way in much echo such as port area, narrow channel, small islands area. The control condition is similar to slightly down GAIN. AT2 Use at open sea to suppress the sea clutter. The control condition is similar to high GAIN. HBR Use at in a bay area, inlet, or a harbor. The control condition becomes manual STC by using the value established HARBOR of ADJUST menu. Note) Refer to "Setting STC circuit(STC)" in section 5.5.4.5.4(6).
PAGE 4
(1) When the "STC" key is pressed, the STC display on the left side of the screen will be reversed as S 35 and the adjustable state will be entered. (2) When the control knob is turned, the figure will be shifted within a range of 0 and 99, and the STC can be manually adjusted. When the "AUTO" key is pressed, all (GAIN, STC and FTC) will enter an AUTO state. (3) After the adjustment is finished, press the "STC" key to exit from the adjustment state.
PAGE 5
.3.9 Man Over Board (MOB) Pressing the MOB key will send the own ship's position data to the external equipment through NMEA port with "WPL" format. There is no change on the screen. To check the MOB position data, select "MOB" from the "WINDOW" menu in the "SETUP". The position of MOB and current position will be displayed on the screen. If press the "MOB" key while watching the MOB screen, MOB data will be cleared and return to previous screen.