http://www.kmwgigatera.
『Safety Precautions Installation』 This symbol is intended to remind the user the presence of actions and operation that may cause danger. Please read instructions carefully and follow the instructions to avoid any danger. This symbol is intended to represent precautions that the user should follow to prevent danger. WARNING Serious injury might result if the following precautions are not followed.
Street Light (HR) Installation & Operation User Guide R Product Overview The information in this document is subject to change without notice 1) Scope Overview This manual describes how to compose, install, and operate LED streetlamps. 2) LED Streetlight Apparatus A streetlight is a light that is installed on the side of least four-lane roads to improve traffic safety of vehicles and civilians as well as traffic efficiency.
Street Light (HR) Installation & Operation User Guide R Precautions before Installation The information in this document is subject to change without notice Precautions before Installation This installation manual is based on the assumption an Electronic Auto Switch is installed to each product. A product with an Electronic Auto Switch may look different from what it looks like in the brochure. Although, the other parts than the Electronic Auto Switch will be installed in the same manner.
Street Light (HR) Installation & Operation User Guide R Package 1 (Standard Type) The information in this document is subject to change without notice ① HR ② Converter Detail Description No Item Purpose ① HR LED Streetlight ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) Copyright ©1991 ~ 2012 KMW, INC. All Rights Reserved Document Revision V0.61 2013.01.
Street Light (HR) Installation & Operation User Guide R Package 2 (Brightness Sending Type) The information in this document is subject to change without notice ① HR ② Converter ③ Illumination Sensor Intensity Detail Description No Item Purpose ① HR LED Streetlight ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) ③ Illumination Sensor In- Surrounding Brightness Based Automatic Power On/Off Function (Photo tensity Sensor) Copyright ©1991 ~ 2012 KMW, INC.
Street Light (HR) Installation & Operation User Guide R Package 3 (Built-In DCM Type) The information in this document is subject to change without notice ① HR ② Converter ③ DCM Detail Description No Item Purpose ① HR LED Streetlight ② Converter Lamp and Brightness Sensor Power Supply Device (SMPS) ③ DCM Data Control Module (*LCS Controller is not included.
Street Light (HR) Installation & Operation User Guide R Package 4 (Package Type) The information in this document is subject to change without notice ① HR ② Converter ③ Illumination Sensor Intensity ④ DCM Detail Description No Item Purpose ① HR LED Streetlight ② Converter LED Streetlight ③ DCM LED Streetlight ④ Illumination Sensor InLED Streetlight tensity Dimming Control Once installed, the DCM module will be synchronized with the LCS system (for illumination control) to enable the di
Open the Product Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 01 Put the product box on an even and flat surface and cut the box along the suture line with a cutter. Please make sure the cutter blade doesn't enter deep enough to scratch the product surface. Also, be careful not to hurt yourself. STEP. 02 Once the box is open, you will see a package fully covering the product.
Brightness Sensor Socket Direction Control (Option) Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 04 As the sun rises from the east and sets to the west, you must direct the Brightness Sensor Receptacle to the north for normal operation of the product. To begin with, use a driver to loosen both bolts like the following figure: If you don't use the Electronic Auto Switch, skip the above step and jump to Step 10. STEP.
Illumination Sensor Intensity Installation (Option) Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 07 The brightness sensor has a directional nature as seen in the following figure: Among the three connection parts, one is designed to be long and wide and the others short and narrow. Please remember that forced installation against the direction nature may damage the lamp connection part.
Open the Converter Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 10 Open the SMPS part from the main body for AC power cable wiring. To begin with, use your thumb to push the latch locker upward and pull the lower part like the following figure: When you zoom in the image, the part that was hidden for easier description purpose will appear STEP.
AC Power Cable Wiring Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 13 Open the SMPS part and hang it on the hook before you start wiring. STEP. 14 Insert the AC power cable behind the arm like the following figure: HR Model basically does not supply the AC power cable. If necessary, it shall be purchased by the user. STEP.
Light Installation Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 16 Keep the lamp and the light pole so arranged that the AC power cable is not stuck between them before you bond them together. STEP. 17 Attach the lamp to the light pole like the following figure: STEP. 18 Once the lamp is installed, use fixing bolts to fix it to the light pole.
AC cable Connection Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 19 Be sure to bond the AC power cable with the SMPS cable. At first, use the twister to connect the two cores of the white cable (N) with each other. Each cable comes from the core after it is connected to the AC power cable and the lamp body. Be sure to use only the cable in the same color for power cable connection.
Lamp Angle Control Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 22 Once the AC power cable is connected, arrange the internal wiring well and close the SMPS cover like the following figure: STEP. 23 This product is structured to control the lighting surface by 5° in vertical direction. Please remember the default of the product is set to 0° when it is shipped out from the factory.
Lamp Angle Control Street Light (HR) Installation & Operation User Guide R The information in this document is subject to change without notice STEP. 25 Remove the fixing bolts in front to lower the lamp by 5°. Push the lamp downward whiling aligning its first and third bolt holes with the corresponding light pole holes and bolt parts together for fixing like the following figure: Put the bolts through the points where both holes are aligned and tighten them firmly. STEP.
RF & Microwave Products The Global Leading RF & LED Provider For America 1521 E. Orangethorpe Ave., Ste. A Fullerton, CA 92831 U.S.A +1.714.515.1100 sales@kmwgigatera.com For Non-America 183-6, Yeongcheon-ro, Dongtan-myeon, Hwaseong-si, Gyeonggi-do, Korea +82.31.370.8720 chriskim@kmw.co.